(Table 1) Conditions of vertical near-bottom profiling and the main parameters of the benthic boundary layer in several regions of the Black Sea shelf

Measurements of 14 vertical profiles of currents and hydrological parameters in the near-bottom layer with depth resolution of 0.1 m were carried out in several regions of the Black Sea shelf, at five points over the continental slope, and in three deep water regions. The upper boundary of the benthic boundary layer (BBL) was reliably determined at a point at distance from 5-7 to 35-40 m from the bottom where the gradients of density and current velocity changed. Experimental data obtained were used to determine the coefficient of bottom friction, friction velocity, coefficients of vertical diffusion of momentum and density, and vertical fluxes of temperature and salinity in the BBL.

(Table 1) Results from XRD analysis as well as sediment type and selected results from ring shear experiments

The location of the seaward tip of a subduction thrust controls material transfer at convergent plate margins, and hence global mass balances. At approximately half of those margins, the material of the subducting plate is completely underthrust so that no accretion or even subduction erosion takes place. Along the remaining margins, material is scraped off the subducting plate and added to the upper plate by frontal accretion. We here examine the physical properties of subducting sediments off Costa Rica and Nankai, type examples for an erosional and an accretionary margin, to investigate which parameters control the level where the frontal thrust cuts into the incoming sediment pile. A series of rotary-shear experiments to measure the frictional strength of the various lithologies entering the two subduction zones were carried out. Results include the following findings: (1) At Costa Rica, clay-rich strata at the top of the incoming succession have the lowest strength (µres = 0.19) while underlying calcareous ooze, chalk and diatomite are strong (up to µres = 0.43; µpeak = 0.56). Hence the entire sediment package is underthrust. (2) Off Japan, clay-rich deposits within the lower Shikoku Basin inventory are weakest (µres = 0.13-0.19) and favour the frontal proto-thrust to migrate into one particular horizon between sandy, competent turbidites below and ash-bearing mud above. (3) Taking in situ data and earlier geotechnical testing into account, it is suggested that mineralogical composition rather than pore-pressure defines the position of the frontal thrust, which locates in the weakest, clay mineral-rich (up to 85 wt.%) materials. (4) Smectite, the dominant clay mineral phase at either margin, shows rate strengthening and stable sliding in the frontal 50 km of the subduction thrust (0.0001-0.1 mm/s, 0.5-25 MPa effective normal stress). (5) Progressive illitization of smectite cannot explain seismogenesis, because illite-rich samples also show velocity strengthening at the conditions tested.

(Table 1) Sediment temperature and thermal conductivity at DSDP Leg 86 Holes

Using a new temperature recording instrument recently developed at the Woods Hole Oceanographic Institution, downhole temperature measurements were made at five sites during Deep Sea Drilling Project Leg 86. The instrument, which can be installed in the shoe of the hydraulic piston corer, allows measurements of sediment temperature to be made simultaneously with the collection of sediment cores. A numerical procedure was applied to correct the temperature disturbance caused by the corer's friction with the sediment. Detailed temperature profiles constructed from the data were combined with the measurement of thermal conductivity to calculate heat flow. Heat flow values were generally low at all sites of Leg 86, consistent with the age of the lithosphere (>100 m.y.) in the Northwestern Pacific Basin.

First-year and second-year snow properties on sea ice in the Weddell Sea during POLARSTERN cruise ANT-XXII/2 (ISPOL) during the drift

Observations of snow properties, superimposed ice, and atmospheric heat fluxes have been performed on first-year and second-year sea ice in the western Weddell Sea, Antarctica. Snow in this region is particular as it does usually survive summer ablation. Measurements were performed during Ice Station Polarstern (ISPOL), a 5-week drift station of the German icebreaker RV Polarstern. Net heat flux to the snowpack was 8 W/m**2, causing only 0.1 to 0.2 m of thinning of both snow cover types, thinner first-year and thicker second-year snow. Snow thinning was dominated by compaction and evaporation, whereas melt was of minor importance and occurred only internally at or close to the surface. Characteristic differences between snow on first-year and second-year ice were found in snow thickness, temperature, and stratigraphy. Snow on second-year ice was thicker, colder, denser, and more layered than on first-year ice. Metamorphism and ablation, and thus mass balance, were similar between both regimes, because they depend more on surface heat fluxes and less on underground properties. Ice freeboard was mostly negative, but flooding occurred mainly on first-year ice. Snow and ice interface temperature did not reach the melting point during the observation period. Nevertheless, formation of discontinuous superimposed ice was observed. Color tracer experiments suggest considerable meltwater percolation within the snow, despite below-melting temperatures of lower layers. Strong meridional gradients of snow and sea-ice properties were found in this region. They suggest similar gradients in atmospheric and oceanographic conditions and implicate their importance for melt processes and the location of the summer ice edge.

(Table 1) Experimental details and results

Factor-of-safety analyses of submarine slope failure depend critically on the shear strength of the slope material, which is often evaluated with residual strength values and for normally consolidated sediments. Here, we report on direct measurements of both shear strength and cohesion for a quartz-clay mixture over a wide range of overconsolidation ratios (OCRs). For normally consolidated sediment at low stresses, cohesion is the dominant source of shear strength compared to friction. Significant increases in peak shear strength occur for OCR > 4, and the primary source of this strength increase is due to increased cohesion, rather than friction. The proportion of added shear strength due to cohesion depends log-linearly on the OCR. We show that at shallow depths where OCR values can be high, overconsolidated clays can be stronger than pure or nearly pure quartz sediments, which are cohesionless under near-surface conditions. Our data also suggest that areas which have experienced significant unroofing due to previous mass movements are less likely to experience subsequent failure at shallow depths due to increased peak strength, and if failure occurs it is expected to be deeper where the OCR is lower. In seismically active areas, this is one potential explanation for the general observation of lower slope failure recurrence compared to rates expected from triggering due to local earthquakes.