(Table 1) Compressional and shear wave velocities and elastic constants of DSDP Hole 83-504B basalts

Compressional and shear wave velocities at confining pressures to 6 kb, densities, and porosities were measured for 32 samples obtained from 836 to 1350 m below seafloor (BSF) in Hole 504B, the section drilled on Leg 83 of the Deep Sea Drilling Project. These data in combination with similar measurements on 28 basalt samples from the section from 274.5 to 836 m, drilled on Legs 69 and 70, provide a comprehensive set of physical property data for over 1000 m of oceanic crust. The velocities, densities, and porosities measured in the laboratory exhibit greater variability in the upper portion of the hole. In general, compressional and shear wave velocities and densities increase with depth, reaching average values at 1 kbar of Vp = 6.45 km/s, Ks = 3.45 km/s and p = 2.94 g/cm3 within the sheeted dike section. Porosities decrease with depth to values generally less than 1% near the bottom of the hole

Physical properties, velocity and attenuation characteristics, and mineralogy of gabbros from ODP Hole 176-735B

Laboratory compressional wave (Vp) and shear wave (Vs) velocities were measured as a function of confining pressure for the gabbros from Hole 735B and compared to results from Leg 118. The upper 500 m of the hole has a Vp mean value of 6895 m/s measured at 200 MPa, and at 500 meters below seafloor (mbsf), Vp measurements show a mean value of 7036 m/s. Vs mean values in the same intervals are 3840 m/s and 3857 m/s, respectively. The mean Vp and Vs values obtained from log data in the upper 600 m are 6520 and 3518 m/s, respectively. These results show a general increase in velocity with depth and the velocity gradients estimate an upper mantle depth of 3.32 km. This value agrees with previous work based on dredged samples and inversion of rare element concentrations in basalts dredged from the conjugate site to the north of the Atlantis Bank. Laboratory measurements show Vp anisotropy ranging between 0.4% and 8.8%, with the majority of the samples having values less than 3.8%. Measurements of velocity anisotropy seem to be associated with zones of high crystal-plastic deformation with predominant preferred mineral orientations of plagioclase, amphiboles, and pyroxenes. These findings are consistent with results on gabbros from the Hess Deep area and suggest that plastic deformation may play an important role in the seismic properties of the lower oceanic crust. In contrast to ophiolite studies, many of the olivine gabbros show a small degree of anisotropy. Log derived Vs anisotropy shows an average of 5.8% for the upper 600 m of Hole 735B and tends to decrease with depth where the overburden pressure and the age of the crustal section suggests closure of cracks and infilling of fractures by alteration minerals. Overall the results indicate that the average shear wave splitting in Hole 735B might be influenced by preferred structural orientations and the average value of shear wave splitting may not be a maximum because structural dips are <90°. The maximum fast-wave orientation values could be influenced by structural features striking slightly oblique to this orientation or by near-field stress concentrations. However, flexural wave dispersion analyses have not been performed to confirm this hypothesis or to indicate to what extent the near-field stresses may be influencing shear wave propagation. Acoustic impedance contrasts calculated from laboratory and logging data were used to generate synthetic seismograms that aid in the interpretation of reflection profiles. Several prominent reflections produced by these calculations suggest that Fe-Ti oxides and shear zones may contribute to the reflective nature of the lower oceanic crust. Laboratory velocity attenuation (Q) measurements from below 500 m have a mean value of 35.1, which is consistent with previous vertical seismic profile (VSP) and laboratory measurements on the upper 500 m.

Seismic velocities at elevated pressures of igneous rocks at DSDP Holes 60-454 and 60-458

The Deep Sea Drilling Project, in addition to providing valuable information on the history and processes of development of the ocean, has significantly contributed to our knowledge of the chemical and physical nature of the upper oceanic crust. Among the important physical properties of the crust are its seismic velocity and structure, the interpretation of which requires laboratory studies of seismic velocities in oceanic rocks.

(Table 1) Physical properties of sediments at DSDP Holes 79-545 and 79-547A

Laboratory measurements of the acoustic and physical properties of deep-sea sediments and rocks are important for the interpretation of seismic reflection and refraction data and estimation of in situ physical property values. Furthermore, the results of such measurements can be used to design geoacoustic models of the upper oceanic crust that can relate the physical properties of deep-sea sediments to lithology, depth of burial, and diagenetic effects (Hamilton, 1980; Milholland et al., 1980). The purpose of this paper is to report the results of laboratory measurements of wet-bulk density, compressionalwave velocity, and velocity anisotropy on sediments cored during DSDP Leg 79. The sample suite consists of 11 calcareous claystones and clay-rich chalks recovered between 370 to 720 m sub-bottom at Holes 545 and 547A.

(Table 1) Summary of acoustic properties at DSDP Holes 60-453 and 60-459B

Laboratory measurements of physical properties are important because the results may be applied to the interpretation of seismic and other types of geophysical data, and because they can be used to estimate the in situ physical properties of different lithologies present beneath the sea floor. In this chapter, wet-bulk densities and compressional-wave velocities, measured at elevated confining pressures, are reported for a suite of seven sediment samples recovered on DSDP Leg 60. Of the seven samples studied, two are mudstones, two are vitric tuffs, and three are chalks. All but one of the samples are from Hole 459B, near the eastern limit of the Mariana fore-arc region. In five cases, velocities were measured parallel and perpendicular to bedding to test for velocity anisotropy.