Air photography Samoylov Island

For the qualitative description of surface properties like vegetation cover or land-water-ratio of Samoylov Island as well as for the evaluation of fetch homogeneity considerations of the eddy covariance measurements and for the up-scaling of chamber flux measurements, a detailed surface classification of the island at the sub-polygonal scale is necessary. However, up to know only grey-scale Corona satellite images from the 1960s with a resolution of 2 x 2 m and recent multi-spectral LandSat images with a resolution of 30 x 30 m were available for this region. Both are not useable for the desired classification because of missing spectral information and inadequate resolution, respectively. During the Lena 2003 expedition, a survey of the island by air photography was carried out in order to obtain images for surface classification. The photographs were taken from a helicopter on 10.07.2002, using a Canon EOS100 reflex camera, a Soligor 19-23 mm lens and colour slide film. The height from which the photographs were taken was approximately 600 meters. Due to limited flight time, not all the area of the island could be photographed and some regions could only be photographed with a slanted view. As a result, the images are of a varying quality and resolution. In Potsdam, after processing the films were scanned using a Nikon LS-2000 scanner at maximal resolution setting. This resulted in a ground resolution of the scanned images of approximately 0.3x0.3 m. The images were subsequently geo-referenced using the ENVI software and a referenced Corona image dating from 18.07.1964 (Spott, 2003). Geo-referencing was only possible for the Holocene river terrace areas; the floodplain regions in the western part of the island could not be referenced due to the lack of ground reference points. In Figure 3.7-1, the aerial view of Samoylov Island composed of the geo-referenced images is shown. Further work is necessary for the classification and interpretation of the images. If possible, air photography surveys will be carried out during future expeditions in order to determine changes in surface pattern and composition.

Seabed photographs taken along OFOS profiles during POLARSTERN cruise PS96 (ANT-XXXI/2 FROSN)

Within the context of the overall ecological working programme Dynamics of Antarctic Marine Shelf Ecosystems (DynAMo) of the PS96 (ANT-XXXI/2) cruise of RV "Polarstern" to the Weddell Sea (Dec 2015 to Feb 2016), seabed imaging surveys were carried out along drift profiles by means of the Ocean Floor Observation System (OFOS) of the Alfred Wegener Institute, Helmholtz Centre for Polar and Marine Research (AWI) Bremerhaven. The setup and mode of deployment of the OFOS was similar to that described by Bergmann and Klages (2012, doi:10.1016/j.marpolbul.2012.09.018). OFOS is a surface-powered gear equipped with two downward-looking cameras installed side-by-side: one high-resolution, wide-angle still camera (CANON® EOS 5D Mark III; lens: Canon EF 24 f/1.4L II, f stop: 13, exposure time: 1/125 sec; in-air view angles: 74° (horizontal), 53° (vertical), 84° (diagonal); image size: 5760 x 3840 px = 21 MPix; front of pressure resistant camera housing consisting of plexiglass dome port) and one high-definition color video camera (SONY® FCB-H11). The system was vertically lowered over the stern of the ship with a broadband fibre-optic cable, until it hovers approximately 1.5 m above the seabed. It was then towed after the slowly sailing ship at a speed of approximately 0.5 kn (0.25 m/s). The ship's Global Acoustic Positioning System (GAPS), combining Ultra Short Base Line (USBL), Inertial Navigation System (INS) and satellite-based Global Positioning System (GPS) technologies, was used to gain highly precise underwater position data of the OFOS. During the profile, OFOS was kept hanging at the preferred height above the seafloor by means of the live video feed and occasional minor cable-length adjustments with the winch to compensate small-scale bathymetric variations in seabed morphology. Information on water depth and height above the seafloor were continuously recorded by means of OFOS-mounted sensors (GAPS transponder, Tritech altimeter). Three lasers, which are placed beside the still camera, emit parallel beams and project red light points, arranged as an equilateral triangle with a side length of 50 cm, in each photo, thus providing a scale that can be used to calculate the seabed area depicted in each image and/or measure the size of organisms or seabed features visible in the image. In addition, the seabed area depicted was estimated using altimeter-derived height above seafloor and optical characteristics of the OFOS still camera. In automatic mode, a seabed photo, depicting an area of approximately 3.45 m**2 (= 2.3 m x 1.5 m; with variations depending on the actual height above ground), was taken every 30 seconds to obtain series of "TIMER" stills distributed at regular distances along the profiles that vary in length depending on duration of the cast. At a ship speed of 0.5 kn, the average distance between seabed images was approximately 5 m. Additional "HOTKEY" photos were taken from interesting objects (organisms, seabed features, such as putative iceberg scours) when they appeared in the live video feed (which was also recorded, in addition to the stills, for documentation and possible later analysis). If any image from this collection is used, please cite the reference as given above.