Basalt density, basement age, and intrusive/extrusive relations from DSDP Legs 2 through 7, 9, and 14

Densities of layer 2 basalt recovered during the Deep Sea Drilling Project have been found to decrease steadily with age, a finding ascribed to progressive submarine weathering in the context of sea-floor spreading. The least-squares solution for 52 density measurements gives a rate of decrease in density of (Delta p)/(Delta t) = -0.0046 g per ccm m.y. = -16 percent per 100 m.y., which is in excellent agreement with earlier estimates based on observed chemical depletion rates of dredged oceanic basalt. Weathering of sea-floor basalt, should it penetrate to any considerable depth in layer 2, will decrease layer 2 seismic refraction velocities, act as a source of geothermal heat, and substantially influence the chemistry of sea water and the overlying column of sediment.

(Table 1) Age and depth of reflectors of the 3.5-kHz and airgun seismic record and their corresponding depth of ash layers, carbonate peaks, and transition zones from DSDP Hole 83-504B

DSDP cores from areas of low (Site 505) and high heat flow (Site 504 B) near the Costa Rica Rift, together with seismic profiles from the Panama Basin, have been studied to determine the relationship between: (1) carbonate content and physical and acoustic properties; and (2) carbonate content, carbonate diagenesis and acoustic stratigraphy. Except for ash and chert layers, bulk density correlates strongly and linearly with carbonate content. Velocity is uniform downcore and only small variations at a small scale are measured. Thus an abrupt change in carbonate content will cause abrupt changes in acoustic impedance and should cause reflectors that can be detected acoustically. A comparison of seismic profiler reflection records with physical properties, carbonate content and reflection coefficients indicates that the main reflectors can be identified with ash layers, diagenetic boundaries, and carbonate content variations. Diagenesis of carbonate sediments is present at Site 504B in a 260 m-thick ooze-chalk-limestone/chert sequence. These diagenetic sequences occur in areas of higher heat flow (200 mW/m**2). Seismic profiler records can be used to map the extent and depth of these diagenetic boundaries.

Velocities and elastic moduli of basalts from Pacific DSDP sites

Compressional (Vp) and shear (Vs) wave velocities have been measured to 10 kb in 32 cores of basalt from 14 Pacific sites of the Deep Sea Drilling Project. Both Vp and V s show wide ranges (3.70 to 6.38 km/sec for Vp and 1.77 to 3.40 km/sec for V s at 0.5 kb) which are linearly related to density and sea floor age, confirming earlier findings by Christensen and Salisbury of decreasing velocity with progressive submarine weathering based on studies of basalts from five sites in the Atlantic. Combined Pacific and Atlantic data give rates of decreasing velocity of -1.89 and -1.35 km/sec per 100 my for Vp and Vs respectively. New analyses of oceanic seismic refraction data indicate a decrease in layer 2 velocities with age similar to that observed in the laboratory, suggesting that weathering penetrates to several hundred meters in many regions and is largely responsible for the extreme range and variability of layer 2 refraction velocities.

(Table 5) Quaternary paleoproductivity of organic carbon in oceans based on DSDP cores

By analogy with the present-day ocean, primary productivity of paleoceans can be reconstructed using calculations based on content of organic carbon in sediments and their accumulation rates. Results of calculations based on published data show that primary productivity of organic carbon, mass of phosphorus involved in the process, and content of phosphorus in ocean waters were relatively stable during Cenozoic and Late Mesozoic. Prior to precipitation on the seafloor together with biogenic detritus, dissolved phosphorus could repeatedly be involved in the biogeochemical cycle. Therefore, only less than 0.1% of phosphorus is retained in bottom sediments. Bulk phosphorus accumulation rate in ocean sediments is partly consistent with calculated primary productivity. Some epochs of phosphate accumulation also coincide with maxima of primary productivity and minima of the fossilization coefficient of organic carbon. The latter fact can testify to episodes of acceleration of organic matter mineralization and release of phosphorus from sediments leading to increase in the phosphorus reserve in paleoceans and phosphate accumulation in some places.

Concentrations and accumulation rates of chemical elements and sediment components in sediments of central equatorial Pacific, DSDP data

Accumulation rates of Mg, Al, Si, Mn, Fe, Ni, Cu, Zn, opal, and calcium carbonate have been calculated from their concentrations in samples from equatorial Deep Sea Drilling Project sites. Maps of element accumulation rates and of Q-mode factors derived from raw data indicate that the flux of trace metals to equatorial Pacific sediments has varied markedly through time and space in response to changes in the relative and absolute influence of several depositional influences: biogenic, detrital, authigenic, and hydrothermal sedimentation. Biologically derived material dominates the sediment of the equatorial Pacific. The distributions of Cu and Zn are most influenced by surface-water biological activity, but Ni, Al, Fe, and Mn are also incorporated into biological material. All of these elements have equatorial accumulation maxima similar to those of opal and calcium carbonate at times during the past 50 m.y. Detritus distributed by trade winds and equatorial surface circulation contributes Al, non-biogenic Si, Fe, and Mg to the region. Detrital sediment is most important in areas with a small supply of biogenic debris and low bulk-accumulation rates. Al accumulation generally increases toward the north and east, indicating its continental source and distribution by the northeast trade winds. Maxima in biological productivity during middle Eocene and latest Miocene to early Pliocene time and concomitant well-developed surface circulation contributed toward temporal maxima in the accumulation rates of Cu, Zn, Ni, and Al in sediments of those ages. Authigenic material is also important only where bulk-sediment accumulation rates are low. Ni, Cu, Zn, and sometimes Mn are associated with this sediment. Fe is almost entirely of hydrothermal origin. Mn is primarily hydrothermal, but some is probably scavenged from sea water by amorphous iron hydroxide floes along with other elements concentrated in hydrothermal sediments, Ni, Cu, and Zn. During the past 50 m.y. all of these elements accumulated over the East Pacific Rise at rates nearly an order of magnitude higher than those at non-rise-crest sites. In addition, factor analysis indicates that some of this material is carried substantial distances to the west of the rise crest. Accumulation rates of Fe in basal metalliferous sediments indicate that the hydrothermal activity that supplied amorphous Fe oxides to the East Pacific Rise areas was most intense during middle Eocene and late Miocene to early Pliocene time.