Lead 210 and silicate profiles from sediments of the equatorial Pacific and South Atlantic

Particle mixing rates have been determined for 5 South Atlantic/Antarctic and 3 equatorial Pacific deep-sea cores using excess 210Pb and 32Si measurements. Radionuclide profiles from these siliceous, calcareous, and clay-rich sediments have been evaluated using a steady state vertical advection diffusion model. In Antarctic siliceous sediments210Pb mixing coefficients (0.04-0.16 cm**2/y) are in reasonable agreement with the 32Si mixing coefficient (0.2 or 0.4 cm**2/y, depending on 32Si half-life). In an equatorial Pacific sediment core, however, the 210Pb mixing coefficient (0.22 cm**2/y) is 3-7 times greater than the 32Si mixing coefficient (0.03 or 0.07 cm**2/y). The difference in 210Pb and 32Si mixing rates in the Pacific sediments results from: (1) non-steady state mixing and differences in characteristic time and depth scales of the two radionuclides, (2) preferential mixing of fine-grained clay particles containing most of the 210Pb activity relative to coarser particles (large radiolaria) containing the 32Si activity, or (3) the supply of 222Rn from the bottom of manganese nodules which increases the measured excess 210Pb activity (relative to 226Ra) at depth and artificially increases the 210Pb mixing coefficient. Based on 32Si data and pore water silica profiles, dissolution of biogenic silica in the sediment column appears to have a minor effect on the 32Si profile in the mixed layer. Deep-sea particle mixing rates reported in this study and the literature do not correlate with sediment type, sediment accumulation rate, or surface productivity. Based on differences in mixing rate among three Antarctic cores collected within 50 km of each other, local variability in the intensity of deep-sea mixing appears to be as important as regional differences in sediment properties.

Chemical and isotopic compositions of volcanics from ODP Hole 210-1276

Site 1276, Leg 210 of the Ocean Drilling Program, was located on the Newfoundland margin in a seismically-defined ~128 Ma "transitional" crust just west of the presumed oceanic crust, and the M3 magnetic anomaly. The goal of drilling on this non-volcanic margin was to study the rifting, nature of basement, and post-rift sedimentation in the Newfoundland-Iberia rift. Drilling of this 1739 m hole was terminated 90-160 m above basement, in the lower of a doublet of alkaline diabase sills. We have carried out geochemical studies of the sill complex, in the hopes that they will provide proxy information regarding the nature of the underlying basement. Excellent 40Ar/39Ar plateau ages were obtained for the two sills: upper sill ~105.3 Ma; lower sill ~97.8 Ma. Thus the sills are substantially younger than the presumed age of the seafloor at site 1276 (~128 Ma), and were intruded beneath substantial sediment overburden (250 m for the upper, older sill, and 575 m for the lower younger sill). While some of the geochemistry of the sills has been compromised by alteration, the "immobile" trace elements show these sills to be hawaiites, differentiated from an enriched alkaline or basanitic parentage. Sr, Nd and Pb isotopes are suggestive of an enriched hotspot/plume mantle source, with a possible "added" component of continental material. These sills unequivocally were not derived from typical MORB (asthenospheric) upper mantle.

Paleogene calcareous nannofossil biostratigraphy of DSDP Hole 21-210

The major objectives of Leg 133 were (1) to define the evolution of the carbonate platforms on the northeastern Australian margin, including their relationship to adjoining basins; and (2) to understand the effects of climate and sea level on their development in space and time (Davies, McKenzie, Palmer-Julson, et al., 1991, doi:10.2973/odp.proc.ir.133.1991). Sixteen sites were drilled, and more than 5.5 km of Neogene core was recovered during Leg 133. However, recovery of Paleogene sediments was unexpectedly poor (a total of a few meters), and the sediments were poorly dated because of strong diagenesis. On the other hand, Site 210 drilled in this region during Leg 21 yielded an expanded Paleogene section, which contains abundant calcareous microfossils. Biostratigraphic information for this section given in Burns, Andrews, et al. (1973, doi:10.2973/dsdp.proc.21.1973) was based primarily on shipboard results. Detailed calcareous nannofossil and planktonic foraminifer biostratigraphies have not been published. Here we provide a detailed documentation of the calcareous nannofossil distribution in the section, biostratigraphically date the section using the modern nannofossil zonation of Okada and Bukry (1980. doi:10.1016/0377-8398(80)90016-X), and construct an age-depth curve based on current knowledge of nannofossil magnetobiochronology. This should provide a useful Paleogene biostratigraphic reference in the northeastern Australian sea, as Site 210 has apparently yielded the most complete Paleogene record in the region. The detailed biostratigraphy should provide a better age constraint for the regional Eocene-Oligocene hiatus recognized previously (e.g., Jenkins and Srinivasan, 1986, doi:10.2973/dsdp.proc.90.113.1986) and should be useful for future studies on various aspects of Paleogene history of the northeastern Australian sea.

(Table T1) Fluid inclusions in siltstone and sandstone grains from ODP Hole 210-1276A

Twenty samples of siltstones and sandstones were taken from Ocean Drilling Program Site 1276 during Leg 210 for fluid inclusion studies. With the exception of one sample of vein calcite, all inclusions were in quartz grains. The results of fluid-inclusion petrology and microthermometry indicate the presence of three fluid inclusion types (Types 1, 2, and 3). Type 1 fluid inclusions are two-phase (liquid + vapor) aqueous inclusions, and Type 2 inclusions are monophase fluid inclusions (liquid or vapor). These are common in all samples and are formed either as primary isolated inclusions or as secondary inclusions as trails along annealed fractures in the grain. Type 3 fluid inclusions are three-phase (liquid + vapor + solid) inclusions. Type 3 inclusions are rare and are observed as isolated inclusions or in a cluster with other types (i.e., Types 1 and 2). The predominant population throughout the different units sampled is two-phase (liquid + vapor) aqueous fluid inclusions (i.e., Type 1). The temperature of homogenization (TH) bivariate plots for Type 1 inclusions shows dominance throughout the hole of low- to medium-salinity fluids with minimum trapping temperatures between 150° and 400°C.