(Table 1) Petrological description and consolidation properties of ODP Site 186-1150 and Hole 186-1151A

In order to determine the shear parameters of the forearc sedimentary strata drilled during Ocean Drilling Program Leg 186, West Pacific Seismic Network, Japan Trench, eight whole-round samples were selected from different depths in the drilled sections of Sites 1150 and 1151. Whereas Site 1150 lays above the seismically active part of the subduction zone, Site 1151 is situated in an aseismic zone. The aim of the triaxial tests was, apart from determination of the static stress strain behavior of the sediments, to test the hypothesis that the static stress strain parameter could differ for each sites. In order to simulate undrained deformation conditions according to the high clay mineral content of the strata, consolidated undrained shear tests were performed in a triaxial testing setup. Measurements of water content, grain density, organic content, and microtextural investigations under the scanning electron microscope (SEM) accompanied the compression experiments. After the saturation and consolidation stages were completed, failure occurred in the compression stage of the experiments at peak strengths of 280-7278 kPa. The stiffness moduli calculated for each sample from differential stress vs. strain curves show a linear relationship with depth and range between 181 and 5827 kPa. Under the SEM, the artificial fault planes of the tested specimen only show partial alignment of clay minerals because of the high content of microfossils.

(Table 3) Foraminiferal 87Sr/86Sr ratios and ages of ODP Hole 162-986D sediments

Site 986 was drilled to 965 meters below seafloor (mbsf) on the western Svalbard margin to record the onset of glaciations and to date and document the glacial evolution in the Svalbard-Barents Sea region during the Pliocene-Pleistocene. In this paper, results of sedimentological analyses are discussed in light of seismic stratigraphy and new age determinations. The latter were difficult to obtain in the glacial deposits, and datums are sparse. Through combined paleomagnetic data, biostratigraphy, and Sr isotopes, however, an overall chronology for the main evolutionary steps is suggested. The cored sequence at Site 986 is younger than 2.6 Ma, and the lower 60 m of the section contains no evidence of a major glacial influence. An initial glaciation is interpreted to have occurred at ~2.3 Ma, resulting in increased sand deposition from debris flows at Site 986 and forming a prominent seismic reflector, R7. However, glaciers probably did not reach the shelf break until ~1.6-1.7 Ma (Reflector R6), after which the depositional environment was dominated by diamictic debris flows. A gradual change in source area from the Barents Sea to Svalbard is recorded primarily by changes in carbonate and smectite content, ~355 mbsf (Reflector R5), at an interpolated age of 1.4-1.5 Ma. During the last ~1 m.y., Site 986 has undergone more distal deposition as the main depocenters have shifted laterally. This has resulted in less frequent debris flows and more turbidites and hemipelagic deposits, with a slight fining upward of the cored sediments.

(Table 2) Physical properties at DSDP Holes 44-391 and 76-534

Laboratory measurements on sediment samples and density well logs run at DSDP Site 534 in the Blake-Bahama Basin were used to establish an in situ velocity and density structure. Synthetic seismograms were generated for comparison to reprocessed seismic reflection data in the vicinity of the Site. Uncertainties in the relative positions of the hole and seismic reflection data, velocity corrections, and the composition of the unrecovered section were evaluated. In light of the errors and compressed section, no unique correlation of the seismic reflection data to the drill hole is completely defensible either in this chapter or elsewhere. The preferred correlation resulting from this exercise is as follows, with the Site 534 report correlation shown in parentheses where different. Horizon beta', 887 m; Horizon beta, 950 m (975 m); Horizon C , 1202 m (1250 m); Horizon C, 1268 m (1340 m); Horizon D', 1342 m (1432 m); Horizon D, 1550 m (1552 m). The major differences in these correlations arise from the use of slightly different velocities and hole location relative to the seismic profiles. The Site 534 report results rely on hole placement on a basement flank, whereas in this chapter we locate it within a basement depression still within the uncertainty of the navigation. The Site 534 report also uses drilling rates, CDP velocity analyses, sonobuoy data, and previous similar drilling correlation methods used at Site 391, along with other geologic considerations in arriving at differing results. Although the correlation method used in this investigation is more objective and the hole location uncertainties better defined, in order to have confidence in any results we will require drilling in areas where reflections are either more widely spaced or where we have better vertical velocity control in the hole.

Particel size distribution and microstructures of sediments from ODP Leg 205 sites (Table 1)

Ocean Drilling Program Legs 170 and 205 offshore Costa Rica provide structural observations which support a new model for the geometry and deformation response to the seismic cycle of the frontal sedimentary prism and decollement. The model is based on drillcore, thin section, and electron microscope observations. The decollement damage zone is a few tens of meters in width, it develops mainly within the frontal prism. A clear cm-thick fault core is observed 1.6 km from the trench. The lower boundary of the fault core is coincident with the lithological boundary between the frontal prism and the hemipelagic and pelagic sediment of the Cocos plate. Breccia clast distributions in the upper portion of the decollement damage zone were studied through fractal analysis. This analysis shows that the fractal dimension changes with brecciated fragment size, implying that deformation was not accommodated by self-similar fracturing. A higher fractal dimensionality correlates with smaller particle size, which indicates that different or additional grain-size reduction processes operated during shearing. The co-existence of two distinct fracturing processes is also confirmed by microscopic analysis in which extension fracturing in the upper part of the damage zone farthest from the fault core is frequent, while both extension and shear fracturing occur approaching the fault core. The coexistence of extensional and shear fracturing seems to be best explained by fluid pressure variations in response to variations of the compressional regime during the seismic cycle. During the co-seismic event, sub-horizontal compression and fluid pressure increase, triggering shear fracturing and fluid expulsion. Fractures migrate upward with fluids, contributing to the asymmetric shape of the decollement, while slip propagates. In the inter-seismic interval the frontal prismrelaxes and fluid pressure drops. The frontal prismgoes into diffuse extension during the intervalwhen plate convergence is accommodated by creep along the ductile fault core. The fault core is typically a barrier to deformation, which is explained by its weak, but impermeable, nature. The localized development of a damage zone beneath the fault core is characterized by shear fracturing that appears as the result of local strengthening of the detachment.

(Table 1) Age and depth of reflectors of the 3.5-kHz and airgun seismic record and their corresponding depth of ash layers, carbonate peaks, and transition zones from DSDP Hole 83-504B

DSDP cores from areas of low (Site 505) and high heat flow (Site 504 B) near the Costa Rica Rift, together with seismic profiles from the Panama Basin, have been studied to determine the relationship between: (1) carbonate content and physical and acoustic properties; and (2) carbonate content, carbonate diagenesis and acoustic stratigraphy. Except for ash and chert layers, bulk density correlates strongly and linearly with carbonate content. Velocity is uniform downcore and only small variations at a small scale are measured. Thus an abrupt change in carbonate content will cause abrupt changes in acoustic impedance and should cause reflectors that can be detected acoustically. A comparison of seismic profiler reflection records with physical properties, carbonate content and reflection coefficients indicates that the main reflectors can be identified with ash layers, diagenetic boundaries, and carbonate content variations. Diagenesis of carbonate sediments is present at Site 504B in a 260 m-thick ooze-chalk-limestone/chert sequence. These diagenetic sequences occur in areas of higher heat flow (200 mW/m**2). Seismic profiler records can be used to map the extent and depth of these diagenetic boundaries.