(Table 3) Textural and bulk mineralogy of Pliocene and Pleistocene sediments from ODP Hole 161-976B

The Pliocene and Pleistocene deposits recovered at Site 976 from the northwestern Alboran Sea at the Málaga base-of-slope include five main sedimentary facies: hemipelagic, turbidite, homogeneous gravity-flow, contourite, and debris-flow facies. The thickness and vertical distribution of these facies into lithostratigraphic Units I, II, and III show that the turbidites and hemipelagic facies are the dominant associations. The Pliocene and Pleistocene depositional history has been divided into three sedimentary stages: Stage I of early Pliocene age, in which hemipelagic and low-energy turbidites were the dominant processes; Stage II of early Pleistocene/late Pliocene age, in which the dominant processes were the turbidity currents interrupted by short episodes of other gravity flows (debris-flows and homogeneous gravity-flow facies) and bottom currents; and Stage III of Pleistocene age, in which both hemipelagic and low-energy gravity-flow processes occurred. The sedimentation during these three stages was controlled mainly by sea-level changes and also by the sediment supply that caused rapid terrigenous sedimentation variations from a proximal source represented by the Fuengirola Canyon.

Calcium carbonate, total and organic carbon and accumulation rate characteristics at DSDP Leg 78A Holes

Bulk sediment accumulation rates and carbonate and carbonate-free accumulation rates corrected for tectonic tilting have been calculated for Leg 78A sediments. These rates are uniformly low, ranging from 0.1 to 6.8 g/(cm**2 x 10**3 yr.), reflecting the pelagic-hemipelagic nature of all the sediments drilled in the northern Lesser Antilles forearc. Rates calculated for Sites 541 and 542 [0.6-6.8 g/(cm**2 x 10**3 yr.)], located on the lower slope of the accretionary prism, are significantly greater than the Neogene rates calculated for oceanic reference Site 543 [0.1-2.4 g/(cm**2 x 10**3)]. This difference could be the result of (1) tectonic thickening of accretionary prism sediments due to folding, small-scale faulting, and layer-parallel shortening; (2) deposition in shallower water farther above the CCD (carbonate compensation depth) resulting in preservation of a greater percentage of calcareous microfossils; or (3) a greater percentage of foraminiferal sediment gravity flows. Terrigenous turbidites are not documented in the Leg 78A area because of (1) great distance from South American sources; (2) damming effects of east-west trending tectonic elements; and (3) location on the Tiburon Rise (Site 543). This lack of terrigenous material, characteristic of intraoceanic convergent margins, suggests that published sedimentation models for active continental convergent margins with abundant terrigenous influxes are not applicable to intraoceanic convergent margin settings.

(Table 3) Foraminiferal 87Sr/86Sr ratios and ages of ODP Hole 162-986D sediments

Site 986 was drilled to 965 meters below seafloor (mbsf) on the western Svalbard margin to record the onset of glaciations and to date and document the glacial evolution in the Svalbard-Barents Sea region during the Pliocene-Pleistocene. In this paper, results of sedimentological analyses are discussed in light of seismic stratigraphy and new age determinations. The latter were difficult to obtain in the glacial deposits, and datums are sparse. Through combined paleomagnetic data, biostratigraphy, and Sr isotopes, however, an overall chronology for the main evolutionary steps is suggested. The cored sequence at Site 986 is younger than 2.6 Ma, and the lower 60 m of the section contains no evidence of a major glacial influence. An initial glaciation is interpreted to have occurred at ~2.3 Ma, resulting in increased sand deposition from debris flows at Site 986 and forming a prominent seismic reflector, R7. However, glaciers probably did not reach the shelf break until ~1.6-1.7 Ma (Reflector R6), after which the depositional environment was dominated by diamictic debris flows. A gradual change in source area from the Barents Sea to Svalbard is recorded primarily by changes in carbonate and smectite content, ~355 mbsf (Reflector R5), at an interpolated age of 1.4-1.5 Ma. During the last ~1 m.y., Site 986 has undergone more distal deposition as the main depocenters have shifted laterally. This has resulted in less frequent debris flows and more turbidites and hemipelagic deposits, with a slight fining upward of the cored sediments.

Organic geochemistry on sediment profiles from the Arctic Ocean

During the ARCTIC '91-Expedition with RV 'Polarstern', several Multicorer and Kastenlot-cores were recovered along a profile crossing the eastern part of the Arctic Ocean. The investigated cores consist mainly of clayey-silty sediments, and some units with a higher sand content. In this thesis, detailed sedimentological and organic-geochemical investigations were performed. In part, the near surface sediments were AMS-14C dated making it possible to Interpret the results of the organic-geochemical investigations in terms of climatic changes (isotopic stage 2 to the Holocene). The more or less absence of foraminifers within the long cores prevented the development of an oxygen isotope stratigraphy. Only the results of core PS2174-5 from the Amundsen-Basin could be discussed in terms of the climatic change that could be dated back to oxygen isotope stage 7. Detailed organic-geochemical investigations in the central Arctic Ocean are rare. Therefore, several different organic-geochemical methods were used to obtain a wide range of data for the Interpretation of the organic matter. The high organic carbon content of the surface sediments is derived from a high input of terrigenous organic matter. The terrigenous organic material is most likely entrained within the sea-ice On the Siberian shelves and released during ice-drift over the Arctic Ocean. Other factors such as iceberg-transport and turbidites are also responsible for the high input of terrigenous organic matter. Due to the more or less closed sea-ice Cover, the Arctic Ocean is known as a low productivity system. A model shows, that only 2 % of the organic matter in central Arctic Ocean sediments is of a marine origin. The influence of the West-Spitsbergen current increases the marine organic matter content to 16 %. Short chain n-alkanes (C17 and C19) can be used as a marker of marine productivity in the Arctic Ocean. Higher contents of short chain n-alkanes exist in surface sediments of the Lomonosov-Ridge and the Makarov-Basin, indicating a higher marine productivity caused by a reduced sea-ice Cover. The Beaufort-Gyre and Transpolar-Drift drift Patterns could be responsible for the lower sea-ice distribution in this region. The sediments of Stage 2 and Stage 3 in this region are also dominated by a higher content of short chain-nalkanes indicating a comparable ice-drift Pattern during that time. The content and composition of organic carbon in the sediments of core PS2174-5 reflect glaciallinterglacial changes. Interglacial stages 7 and 5e show a low organic carbon content (C 0,5 %) and, as indicated by high hydrogen-indices, low CIN-ratios, higher content of n-alkanes (C17 and C19) and a higher opal content, a higher marine productivity. In the Holocene, a high content of foraminifers, coccoliths, ostracodes, and sponge spicules indicate higher surface-water productivity. Nevertheless, the low hydrogenindices reveal a high content of terrigenous organic matter. Therefore, the Holocene seems to be different from interglacials 7 and 5e. During the glacial periods (stages 6, upper 5, and 4), TOC-values are significantly higher (0.7 to 1.3 %). In addition, low hydrogen-indices, high CIN-ratios, low short chain n-alkanes and opal contents provide evidence for a higher input of terrigenous organic matter and reduced marine productivity. The high lignin content in core sections with high TOC-contents, substantiates the high input of terrigenous organic matter. Changes in the content and composition of the organic carbon is believed to vary with the fluctuations in sea-level and sea-ice coverage.

Petrophysical measurement of ODP Leg 122 and 123 samples (Tables 1, 2)

The capillary-pressure characteristics of 22 samples of lithified post-Paleozoic Indian-Ocean carbonates were compared to published data from older carbonate rocks (lower Paleozoic Hunton Group of Texas and Oklahoma). The Indian-Ocean samples are considerably more porous than are the Paleozoic samples, yet all of the Indian-Ocean samples fit readily into a descriptive petrofacies scheme previously established for the Hunton Group. The Indian-Ocean samples may be assigned to four petrophysical facies (petrofacies) based on the shapes of their capillary-pressure curves, their pore-throat-size distributions, their estimated recovery efficiency values (for nonwetting fluids), and the visual characteristics of their pore systems, as observed with a scanning-electron microscope. Petrofacies assignments for the Indian-Ocean samples are as follows. Petrofacies I includes six samples collected from the coarse basal portions of event deposits (primarily turbidites). These samples have large throats, leptokurtic throat-size distributions, low- to moderate recovery efficiency values, concave cumulative-intrusion capillary-pressure curves, and high porosity values. Petrofacies II includes two sedimentologically dissimilar samples that have medium-size throats, platykurtic throat-size distributions, moderate- to-high recovery efficiency values, gently sloping cumulative-intrusion capillary-pressure curves, and high porosity values. Petrofacies III includes two polymictic sandstones and a skeletal packstone that have small throats, polymodal throat-size distributions, moderate recovery efficiency values, gently sloping cumulative-intrusion capillary-pressure curves, and high porosity values. Petrofacies IV includes 11 samples, mostly recrystallized neritic carbonates, that have small throats, leptokurtic throat-size distributions, high recovery efficiency values, convex cumulative-intrusion capillary-pressure curves, and low porosity values. Comparison of petrofacies assignment to core-, thin-section-, and smear-slide data, and to inferred depositional setting, suggests that pore systems in most samples from Holes 765C and 766A result from primary depositional features, whereas pore systems in samples from Hole 761C and one sample from Hole 765C have been strongly influenced by diagenetic processes. For Hole 761C, prediction of petrophysical parameters should be most successful if based on diagenetic facies patterns. By contrast, the distribution of favorable reservoir facies and of permeability barriers in less highly altered rocks collected from Holes 765C and 766A is related to depositional patterns. Recovery efficiency is inversely related to both porosity and median throat size for the present data set. This relationship is similar to that observed for carbonates of the lower Paleozoic Hunton Group and the Ordovician Ellenburger dolomite, but opposite of that observed for some other ancient carbonates. The coarse deposits of the massive basal units of turbidites are petrophysically distinct and form a coherent petrophysical group (Petrofacies I) with substantial reservoir potential. Two samples assigned to Petrofacies I have extremely large throats (median throat size at least 4 ?m, and at least six times that of any other sample) and therefore high permeability values. These two samples come from thin, coarse turbidites that lack or have poorly developed fine divisions and are interpreted to have been deposited on channeled suprafan lobes in a proximal mid-fan setting. The restriction of extremely high permeability values to a single depositional facies suggests that careful facies mapping of deep-sea fans in a deliberate search for such coarse turbidites could dramatically enhance the success of exploration for aquifers or hydrocarbon reservoirs. Such reservoirs should have substantial vertical heterogeneity. They should have high lateral permeability values but low vertical permeability values, and reservoir sections should include numerous thin units having widely differing petrophysical characteristics.

Ripple migration directions and grain fabric measurements on ODP Hole 210-1276A sediments

Albian turbidites and intercalated shales were cored from ~1145 to 1700 meters below seafloor at Site 1276 in the Newfoundland Basin. Strata at this level dip ~2.5° seaward (toward an azimuth of ~130°) based on seismic profiles. In contrast, beds dip an average of ~10° in the cores. This higher apparent dip is the sum of the ~2.5° seaward dip and a measured hole deviation of 7.43°, which must be essentially in the same seaward direction. Using the maximum dip direction in the cores as a reference direction, paleocurrents were measured from 11 current-ripple foresets and 11 vector means of grain fabric in planar-laminated sandstones. Five of the planar-laminated sandstone samples have a grain imbrication 8°, permitting specification of a unique flow direction rather than just the line-of-motion of the current. Both ripples and grain fabric point to unconfined flow toward the north-northeast. There is considerable spread in the data so that some paleoflow indicators point toward the northwest, whereas others point southeast. Nevertheless, the overall pattern of paleoflow suggests a source for the turbidity currents on the southeastern Grand Banks, likely from the long-emergent Avalon Uplift in that area. On average, turbidity currents apparently flowed axially in the young Albian rift, toward the north. This is opposite to what might be expected for a northward-propagating rift and a young ocean opening in a zipperlike fashion from south to north.

(Table 2) Aragonite, high and low magnesium calcite, major elements, bioclast and planktic foraminifera from ODP Hole 133-817A

Investigation of the Middle Miocene-Pleistocene succession in cores at ODP Site 817A (Leg 133), drilled on the slope south of the Queensland Plateau, identified the various material fluxes contributing to sedimentation and has determined thereby the paleogeographic events which occurred close to the studied area and influenced these fluxes. To determine proportions of platform origin and of plankton origin of carbonate mud, two reference sediments were collected: (1) back-reef carbonate mud from the Young Reef area (Great Barrier Reef); and (2) Late Miocene chalk from the Loyalty Basin, off New Caledonia. Through their biofacies and mineralogical and geochemical characters, these reference sediments were used to distinguish the proportions of platform and basin components in carbonate muds of 25 core samples from Hole 817A. Two "origin indexes" (i1 and i2) relate the proportion in platform and basin materials. The relative sedimentation rate is inferred from the high-frequency cycles determined by redox intervals in the cores. Bulk carbonate deposited in each core has been calculated in two ways with close results: (1) from calcimetric data available in the Leg 133 preliminary reports (Davies et al., 1991); and (2) from average magnetic susceptibility of cores, a value negatively correlated to the average carbonate content. Vertical changes in sedimentation rates, in carbonate content, in origin indexes and in "linear fluxes" document the evolution of sediment origins from platform carbonates, planktonic carbonates and insoluble material through time. These data are augmented with the variations in organic-matter content through the 817A succession. The observed changes and their interpretation are not modified by compaction, and are compatible with major paleogeographic events including drowning of the Queensland Plateau (Middle Miocene-Early Pliocene) and the renewal of shallow carbonate production, (1) during the Late Pliocene, and (2) from the Early Pleistocene. The birth and growth of the Great Barrier Reef is also recorded from 0.5 Ma by a strengthening of detrital carbonate deposition and possibly by a lack of clay minerals in the 4 upper cores, a response to trapping of terrigenous material behind this barrier. In addition, a maximum of biological silica production is displayed in the Middle Miocene. These changes constrain the time of events and the sequence-stratigraphy framework some components of which are transgression surface, maximum flooding surface and low-stand turbidites. Sedimentation rates and material fluxes show cycles lasting 1.75 Myr. Whatever their origin (climatic and/or eustatic) these cycles affected the planktonic production primarily. The changes also show that major carbonate variations in the deposits are due to a dilution effect by insoluble material (clay, biogenic silica and volcanic glasses) and that plankton productivity, controlling the major fraction of carbonate sedimentation, depends principally on terrigenous supplies, but also on deep-water upwelling. Accuracy of the method is reduced by redeposition, reworking, and probable occurrence of hiatuses.

Mineral and chemical composition of hydrothermally altered rocks and sediments from the Middle Valley, ODP Leg 139 data

The Middle Valley segment at the northern end of the Juan de Fuca Ridge is a deep extensional rift blanketed with 200-500 m of Pleistocene turbiditic sediment. Sites 857 and 858 were drilled during Ocean Drilling Program Leg 139 to determine whether these two sites were hydrologically linked end members of an active hydrothermal circulation system. Site 858 was placed in an area of active hydrothermal discharge with fluids up to 270°C venting through anhydrite-bearing mounds on top of altered sediment. The shallow basement of fine-grained basalt that underlies the vents at Site 858 is interpreted as a seamount that was subsequently buried by turbidites. Site 857 was placed 1.6 km south of the Site 858 vents in a zone of high heat flow and numerous seismically imaged ridge-parallel faults. Drilling at Site 857 encountered sediments that are increasingly altered with depth and that overlie a series of mafic sills at depths of 460-940 m below sea floor. Sill margins and adjacent baked sediment are highly altered to magnesian chlorite and crosscut with veins filled with quartz, chlorite, sulfides, epidote, and wairakite. The sill interiors vary from slightly altered, with unaltered plagioclase and clinopyroxene in a mesostasis replaced by chlorite, to local zones of intense alteration and brecciation. In these latter zones, the sill interiors are pervasively replaced by chlorite, epidote, quartz, pyrite, titanite, and rare actinolite. The most complete replacement is associated with brecciated horizons with low recovery and slickensides on fracture surfaces, which we interpret as intersections between faults and the sills. Geochemically, the alteration of the sill complex is reflected in significant whole-rock depletions in Ca, Sr, and Na with corresponding enrichments in Mg, Al, and most metals. The latter results from the formation of conspicuous sulfide poikiloblasts. In contrast, metamorphism of the Site 858 seamount includes incomplete albitization of plagioclase phenocrysts and replacement of sparse mafic phenocrysts. Much of the basement alteration at Site 858 is confined to crosscutting veins except for a highly altered and veined horizon at the contact between basaltic basement and the overlying sediment. The sill complex at Site 857 is more highly depleted in 18O (d18O = 2.4 per mil - 4.7 per mil) and more pervasively replaced by secondary minerals relative to the extrusives at Site 858 (d18O = 4.5 per mil - 5.5 per mil). There is no evidence of significant albitization of the plagioclase at Site 857, suggesting high Ca/Na in the pore fluids. Fluid-inclusion data from hydrothermal minerals in altered mafic rocks and veins at Sites 857 and 858 show a consistency of homogenization temperatures, varying from 245 to 270°C, which is within the range of temperatures observed for the fluids venting at Site 858. The consistency of the fluid inclusion temperatures, the lack of albitization within the Site 857 sills, and the apparently low water/rock ratio collectively suggest that the sill complex at Site 857 is in thermal equilibrium and being altered by a highly evolved Ca-rich fluid similar to the fluids now venting at Site 858. The alteration evident in these two deep crustal drillsites is a result of the ongoing hydrothermal circulation and is consistent with downhole logging results, instrumented borehole results, and hydrothermal fluid chemistry. The pervasive alteration of the laterally extensive sill-sediment complex at Site 857 determines the chemistry of the fluids that are venting at Site 858. The limited alteration of the Site 858 lavas suggests that this basement edifice acts as a penetrator or ventilator for the regional hydrothermal reservoir with much of the flow focussed at the highly altered and veined sediment-basalt contact.

(Table 1) Ooze/chalk cycles: frequency of occurrence at DSDP Leg 74 Sites

Shallow- to deep-water environments are represented by the sediments and rocks recovered from the Walvis Ridge- Angola Basin transect. These calcareous oozes, chalks, limestones, and volcaniclastic sedimentary rocks are used to define and correlate four lithostratigraphic units. The sediments were deposited in cycles which represent recurring tectonic or Oceanographic events and may be related to climatic fluctuations and orbital perturbations. Turbidites are the most common and easily identified sedimentary cycle. They are Late Cretaceous to Paleocene in age and are repeated in intervals ranging from thousands to tens of thousands of years. They are also found interbedded between basalt layers. Turbidites are easily distinguished from the other cycles present by their sedimentary structures, mineral composition, alteration products, and physical properties (GRAPE) data. Large-scale turbidites, debris, or slump breccias are found at or just above the Cretaceous/Tertiary boundary and indicate an event of considerable energy possibly related to intense tectonic activity. Diagenetic cycles, interpreted as small-scale dissolution cycles or sequences produced by biogenic activity, occur in early Paleocene chalks. The recurrence intervals average -20,000 y. but have a wide range of values. Variations in CaCO3 content, color, gradational boundaries, and trace fossil content characterize these sediments. These cycles reflect bottom-water conditions. Ooze-chalk cycles occur in upper Oligocene to upper Paleocene sediments and represent conditions that once existed at the sediment/water interface where they obtained their diagenetic potential. These oscillations are repeated over tens of thousands of years and may have no modern analogs. Color variations in sediments at the Cretaceous/Tertiary boundary indicate local fluctuations in oxygen content within the sediments or the water column. This situation lasted for several hundred thousand years and is not repeated elsewhere in the sequence. Large dissolution cycles are recorded in the sediments at Site 527 that are of middle Miocene and early Oligocene to middle Eocene age. During this time the seafloor at this site appears to have been located at or subsided to a depth occupied by a fluctuating CCD and lysocline.