Physical and geotechnical properties of Norwegian Sea sediments

Sediment composition and rate of deposition are the primary factors responsible for determining the spatial distribution of geotechnical properties on the Wring Plateau. Grain size and depth of burial have no significant influence. Vertical and lateral changes in geotechnical properties are associated with vertical and lateral composition changes in which biogenic silica is the most important variable. Anomalous trends of decreasing density and increasing porosity and water content with depth are associated with increasing silica content downsection. Void ratios, inferred in-situ permeability, and change in void ratio during consolidation testing are relatively high in siliceous sediments and tend to increase as the biogenic silica content increases. Portions of the section are overconsolidated, probably as a result of changes in sediment accumulation rates. However, the higher permeabilities of siliceous sediments may also be a factor influencing consolidation state.

Whole rock geochemistry and stable isotopes of rocks, fragments and foraminifers from two ODP Leg 166 holes

Total carbon and carbonate contents, quantitative carbonate mineralogy, trace metal concentrations, and stable isotope compositions were determined on a suite of samples from the Miocene sections at Sites 1006 and 1007. The Miocene section at Site 1007, located at the toe-of-slope, contains a relatively high proportion of bank-derived components and becomes fully lithified at a depth of ~300 meters below seafloor (mbsf). By contrast, Miocene sediments at Site 1006, situated in Neogene drift deposits in the Straits of Florida and composed primarily of pelagic carbonates, do not become fully lithified until a depth of ~675 mbsf. Diagenetic and compositional contrasts between Sites 1006 and 1007 are reflected in geochemical data derived from sediment samples from each site.

Low-molecular-weight hydrocarbon concentrations, organic carbon contents, and Rock-Eval pyrolysis hydrogen indices at DSDP Holes 75-530A and 75-532

A series of C2-C8 hydrocarbons (including saturated, aromatic, and olefinic compounds) from deep-frozen core samples taken during DSDP Leg 75 (Holes 530A and 532) were analyzed by a combined hydrogen-stripping/thermovaporization method. Concentrations representing both hydrocarbons dissolved in the pore water and adsorbed on the mineral surfaces vary in Hole 530A from about 10 to 15,000 ng/g of dry sediment weight depending on the lithology (organic-carbon-lean calcareous oozes versus "black shales"). Likewise, the organic-carbon-normalized C2-C8 hydrocarbon concentrations vary from 3,500 to 93,100 ng/g Corg, reflecting drastic differences in the hydrogen contents and hence the hydrocarbon potential of the kerogens. The highest concentrations measured of nearly 10**5 ng/g Corg are about two orders of magnitude below those usually encountered in Type-II kerogen-bearing source beds in the main phase of petroleum generation. Therefore, it was concluded that Hole 530A sediments, even at 1100 m depth, are in an early stage of evolution. The corresponding data from Hole 532 indicated lower amounts (3,000-9,000 ng/g Corg), which is in accordance with the shallow burial depth and immaturity of these Pliocene/late Miocene sediments. Significant changes in the light hydrocarbon composition with depth were attributed either to changes in kerogen type or to maturity related effects. Redistribution pheonomena, possibly the result of diffusion, were recognized only sporadically in Hole 530A, where several organic-carbon lean samples were enriched by migrated gaseous hydrocarbons. The core samples from Hole 530A were found to be severely contaminated by large quantities of acetone, which is routinely used as a solvent during sampling procedures on board Glomar Challenger.

Planktonic foraminiferal stratigraphy of sediments from ODP Leg 173 sites

Planktonic foraminifers recovered from five sites drilled off western Portugal during Ocean Drilling Program Leg 173 are documented. Hole 1065A yielded planktonic foraminifers from Miocene sediments in Sections 173-1065A-1R-1 through 6R-2. Hole 1067A penetrated middle Eocene sediments containing planktonic foraminifers in Section 173-1067A-1R-1 through Lower Eocene planktonic foraminiferal horizons to Section 12R-CC. Hole 1068A yielded planktonic foraminiferal assemblages from middle Eocene sediments at Section 173-1068A-1R-1 to Maastrichtian sediments at Section 173-1068A-15R-3, whereas Hole 1069A contained middle Eocene taxa in Section 173-1069A-1R-1 through Campanian/Maastrichtian forms in Section 173-1069A-15R-2. All of the planktonic foraminifers recovered from these sites are of poor to moderately good preservation and are variable in abundance. Hole 1070A yielded only six planktonic foraminifers, with the assemblages being dominated by benthic foraminifers and fish teeth. The co-occurrence of other microfossil groups, including benthic foraminifers, are only briefly discussed here. The lower Miocene biosiliceous facies recorded in Hole 1065A is considered to be coeval with a similar facies found in onshore sections farther to the east, in southern Spain.