Timing of Tertiary Extension in the Railroad Valley Pioche Transect, Nevada: Constraints from Ar-40/Ar-39 Ages of Volcanic Rocks

Time-space relations of extension and volcanism place critical constraints on models of Basin and Range extensional processes. This paper addresses such relations in a 130-km-wide transect in the eastern Great Basin, bounded on the east by the Ely Springs Range and on the west by the Grant and Quinn Canyon ranges. Stratigraphic and structural data, combined with 40Ar/39Ar isotopic ages of volcanic rocks, document a protracted but distinctly episodic extensional history. Field relations indicate four periods of faulting. Only one of these periods was synchronous with nearby volcanic activity, which implies that volcanism and faulting need not be associated closely in space and time. Based on published dates and the analyses reported here, the periods of extension were (1) prevolcanic (pre-32 Ma), (2) early synvolcanic (30 to 27 Ma), (3) immediately postvolcanic (about 16 to 14 Ma), and (4) Pliocene to Quaternary. The break between the second and third periods is distinct. The minimum gap between the first two periods is 2 Ma, but the separation may be much larger. Temporal separation of the last two periods is only suggested by the stratigraphic record and cannot be rigorously demonstrated with present data. The three younger periods of faulting apparently occurred across the entire transect. The oldest period is recognized only at the eastern end of the transect, but appears to correlate about 150 km northward along strike with extension in the Northern Snake Range-Kern Mountains area. Therefore the oldest period also is regional in extent, but affected a different area than that affected by younger periods. This relation suggests that distinct extensional structures and master detachment faults were active at different times. The correlation of deformation periods of a few million years duration across the Railroad Valley-Pioche transect suggests that the scale of active extensional domains in the Great Basin may be greater than 100 km across strike.

Effects of Strand Geometry on Selected Properties of Long-Stand Structural Composite Lumber Made from Northeastern Hardwoods

Structural composite lumber (SCL) products often possess significantly higher design values than the top grades of solid lumber, making it a popular choice for both residential and commercial applications. The enhanced mechanical properties of SCL are mainly due to defect randomization and densification of the wood fiber, both largely functions of the size, shape and composition (species) of the wood element. Traditionally, SCL manufacturers have used thin, rectangular elements produced from either moderate density softwoods or low density hardwoods. Higher density hardwood species have been avoided, as they require higher pressures to adequately densify and consolidate the wood furnish. These higher pressures can lead to increased manufacturing costs, damage to the wood fiber and/or a product that is too dense, making it heavy and unreceptive to common mechanical fastening techniques. In the northeastern United States high density, diffuse-porous hardwoods (such as maple, beech and birch) are abundant. Use of these species as primary furnish for a SCL product may allow for a competitive advantage in terms of resource cost against products that rely on veneer grade logs. Proximity to this abundant and relatively inexpensive resource may facilitate entry of SCL production facilities in the northeastern United States, where currently none exist. However, modifications to current strand sizes, geometries or production techniques will likely be required to allow for use of these species. A new SCL product concept has been invented allowing for use of these high density hardwoods. The product, referred to as long-strand structural composite lumber (LSSCL), uses strands of significantly larger cross sectional areas and volumes than existing SCL products. In spite of the large strand size, satisfactory consolidation is achieved without excessive densification of the wood fiber through use of a symmetrical strand geometric cross-section. LSSCL density is similar to that of existing SCL products, but is due mainly to the inherent density of the species, rather than through densification. An experiment was designed and conducted producing LSSCL from both large (7/16”) and small (1/4”) strands, of both square and triangular geometric cross sections. Testing results indicate that the large, triangular strands produce LSSCL beams with projected design values of: Modulus of elasticity (MOEapp) – 1,750,000 psi; Allowable bending stress (Fb) – 2750 psi; Allowable shear stress (Fv) – 260 psi. Several modifications are recommended which may lead to improvement of these values, likely allowing for competition against existing SCL products.