The Leaching of Electrodeposition of Iron

Electrolytic iron as deposited is brittle and therefore must be annealed. After annealing, the material is ductile and closely resembles copper in its behavior under work. It is claimed to be more resistant to corrosion than dead soft iron. It also has the advantage of corroding uniformly ( or­dinary soft iron develops pin holes which shorten its life considerably). The extreme purity of electrolytic iron namely makes it very suitable as a base metal for alloys. Its ductility opens up a field for use in the manufacture of cold rolled strip, seamless tubes, and wire.

The Effect of Impurities on the Electrodeposition of Zinc from Zinc Sulfate Solution Containing Antimony.

It has been proven by research and years of experience, that before electrolytic zinc is possible, the electrolyte, as zinc sulfate solution must be prepared as pure as is economical. In other words, the ideal electrolyte must only be a solution of one metal - zinc. Every other metal and carbon must be excluded if good recovery and a firm deposit is to be obtained.

The Electrodeposition of Manganese from Certain Aqueous Solutions

Careful examination of the literature available shows that the electrodeposition of manganese from various aqueous solutions has not been attempted to any great extent. The best method for the electrodeposition of pure manganese consists in the electrolysis of a solution con­taining manganous and ammonium sulphates.

The Electrodeposition of Manganese from Certain Aqueous Solutions.

Manganese has been successfully electrodeposited from aqueous solutions in past years by several work­ers in electrochemical and electrometallurgical fields. The present work was concerned, primarily, with investigation of electrodeposition from solutions which are commercially obtainable from the hydrometallurgical or pyrometallurgical treatment of the low grade mangan­ese deposits of this country.

The Electrodeposition of Chromium from Trivalent Salt Solutions

The enormous number of previous experiments and researches for the improvement of the commercial chromic acid bath, did not succeed even in the partial elimination of any one of the disadvantages of chromic acid bath. This led the author to believe that the poor performance is an inherent quality of the chromic acid bath, and is due to the fact that the deposition occurs from the higher state of oxidation.

The Electrodeposition of Iron-Manganese Alloys

Various electrolytes were experimented with in an attempt to deposit an iron-manganese alloy. An Alloy was obtained from a solution containing ferrous ammonium sulfate, manganous sulfate, and ammonium sulfate. Further experimentation was done in an effort to determine the optimum conditions of deposition and the highest manganese alloy which could be produced.

The Electrodeposition of Iron-Manganese Alloys

An electrodeposition of an iron-manganese alloy was made from the same conditions determined by previous re­search. Various addition agents were experimented with in an attempt to produce better conditions for electro-deposition. It was found advantageous to add small a­mounts of sodium lauryl sulfate and ammonium sulfite to the electrolyte.

The Electrodeposition of Copper-Cobalt Alloys

An attempt was made to deposit a 50:50 copper-cobalt alloy from various sulfate electrolytes. No true 50:50 alloy was obtained but various mixtures of cobalt and copper rich crystals were deposited.

The Electrodeposition of Iron-Manganese Alloys

Although the alteration of properties resulting from the alloying of metals in their usual commercial forms has been extensively investigated, the field of electrodeposition of alloys is believed generally not to have received the atten­tion that it merits.

The Continuous Electrodeposition of Manganese

The object of this research was to produce a workable electrolytic cell for the continuous deposition of manganese from aqueous sulphate solutions and determine the critical factors in its oper­ation.

The Electroformation of Lithium-Lead Alloys from Molten Electrolytes

An attempt was made to make lead-lithium alloys by electrodeposition of lithium using a molten bath and a molten lead cathode.The variables taken into consideration were: composition of the melt, temperature of the melt, and current density. The purpose of changing these factors was to determine what effect each had on the current efficiency.

The Theory of Alloy Deposition and The Effect of a Rotating Cathode Upon Such Deposition, with Special Attention to the Possibility of Depositing Sterling Silver

In the past few years a great deal of atten­tion has been given to the electrodeposition of alloys. For the main part, this investigation has been of scien­tific interest only; but in a few instances, such work has attained commercial importance.

Analytical Parametric Model Used to Study the Influence of Electrostatic Force on Surface Coverage During Electrospinning of Polymer Fibers

Electrospinning (ES) can readily produce polymer fibers with cross-sectional dimensions ranging from tens of nanometers to tens of microns. Qualitative estimates of surface area coverage are rather intuitive. However, quantitative analytical and numerical methods for predicting surface coverage during ES have not been covered in sufficient depth to be applied in the design of novel materials, surfaces, and devices from ES fibers. This article presents a modeling approach to ES surface coverage where an analytical model is derived for use in quantitative prediction of surface coverage of ES fibers. The analytical model is used to predict the diameter of circular deposition areas of constant field strength and constant electrostatic force. Experimental results of polyvinyl alcohol fibers are reported and compared to numerical models to supplement the analytical model derived. The analytical model provides scientists and engineers a method for estimating surface area coverage. Both applied voltage and capillary-to-collection-plate separation are treated as independent variables for the analysis. The electric field produced by the ES process was modeled using COMSOL Multiphysics software to determine a correlation between the applied field strength and the size of the deposition area of the ES fibers. MATLAB scripts were utilized to combine the numerical COMSOL results with derived analytical equations. Experimental results reinforce the parametric trends produced via modeling and lend credibility to the use of modeling techniques for the qualitative prediction of surface area coverage from ES. (Copyright: 2014 American Vacuum Society.)