Evaluating northern hardwood management using retrospective analysis and diameter distributions

Northern hardwood management was assessed throughout the state of Michigan using data collected on recently harvested stands in 2010 and 2011. Methods of forensic estimation of diameter at breast height were compared and an ideal, localized equation form was selected for use in reconstructing pre-harvest stand structures. Comparisons showed differences in predictive ability among available equation forms which led to substantial financial differences when used to estimate the value of removed timber. Management on all stands was then compared among state, private, and corporate landowners. Comparisons of harvest intensities against a liberal interpretation of a well-established management guideline showed that approximately one third of harvests were conducted in a manner which may imply that the guideline was followed. One third showed higher levels of removals than recommended, and one third of harvests were less intensive than recommended. Multiple management guidelines and postulated objectives were then synthesized into a novel system of harvest taxonomy, against which all harvests were compared. This further comparison showed approximately the same proportions of harvests, while distinguishing sanitation cuts and the future productive potential of harvests cut more intensely than suggested by guidelines. Stand structures are commonly represented using diameter distributions. Parametric and nonparametric techniques for describing diameter distributions were employed on pre-harvest and post-harvest data. A common polynomial regression procedure was found to be highly sensitive to the method of histogram construction which provides the data points for the regression. The discriminative ability of kernel density estimation was substantially different from that of the polynomial regression technique.

STRUCTURAL CONTROL OF A SMALL-SCALE TEST-BED SHAKER STRUCTURE USING A SPONGE-TYPE MAGNETO-RHEOLOGICAL FLUID DAMPER

Semi-active damping devices have been shown to be effective in mitigating unwanted vibrations in civil structures. These devices impart force indirectly through real-time alterations to structural properties. Simulating the complex behavior of these devices for laboratory-scale experiments is a major challenge. Commercial devices for seismic applications typically operate in the 2-10 kN range; this force is too high for small-scale testing applications where requirements typically range from 0-10 N. Several challenges must be overcome to produce damping forces at this level. In this study, a small-scale magneto-rheological (MR) damper utilizing a fluid absorbent metal foam matrix is developed and tested to accomplish this goal. This matrix allows magneto-rheological (MR) fluid to be extracted upon magnetic excitation in order to produce MR-fluid shear stresses and viscosity effects between an electromagnetic piston, the foam, and the damper housing. Dampers for uniaxial seismic excitation are traditionally positioned in the horizontal orientation allowing MR-fluid to gather in the lower part of the damper housing when partially filled. Thus, the absorbent matrix is placed in the bottom of the housing relieving the need to fill the entire device with MR-fluid, a practice that requires seals that add significant unwanted friction to the desired low-force device. The damper, once constructed, can be used in feedback control applications to reduce seismic vibrations and to test structural control algorithms and wireless command devices. To validate this device, a parametric study was performed utilizing force and acceleration measurements to characterize damper performance and controllability for this actuator. A discussion of the results is presented to demonstrate the attainment of the damper design objectives.

Understanding "Just Enough" Computer Users: Motivation Style and Proficiency

Among daily computer users who are proficient, some are flexible at accomplishing unfamiliar tasks on their own and others have difficulty. Software designers and evaluators involved with Human Computer Interaction (HCI) should account for any group of proficient daily users that are shown to stumble over unfamiliar tasks. We define "Just Enough" (JE) users as proficient daily computer users with predominantly extrinsic motivation style who know just enough to get what they want or need from the computer. We hypothesize that JE users have difficulty with unfamiliar computer tasks and skill transfer, whereas intrinsically motivated daily users accomplish unfamiliar tasks readily. Intrinsic motivation can be characterized by interest, enjoyment, and choice and extrinsic motivation is externally regulated. In our study we identified users by motivation style and then did ethnographic observations. Our results confirm that JE users do have difficulty accomplishing unfamiliar tasks on their own but had fewer problems with near skill transfer. In contrast, intrinsically motivated users had no trouble with unfamiliar tasks nor with near skill transfer. This supports our assertion that JE users know enough to get routine tasks done and can transfer that knowledge, but become unproductive when faced with unfamiliar tasks. This study combines quantitative and qualitative methods. We identified 66 daily users by motivation style using an inventory adapted from Deci and Ryan (Ryan and Deci 2000) and from Guay, Vallerand, and Blanchard (Guay et al. 2000). We used qualitative ethnographic methods with a think aloud protocol to observe nine extrinsic users and seven intrinsic users. Observation sessions had three customized phases where the researcher directed the participant to: 1) confirm the participant's proficiency; 2) test the participant accomplishing unfamiliar tasks; and 3) test transfer of existing skills to unfamiliar software.