Inductive-Capacitive Resonant Circuit Sensors for Structural Health and Environmental Monitoring

Inductive-capacitive (LC) resonant circuit sensors are low-cost, wireless, durable, simple to fabricate and battery-less. Consequently, they are well suited to sensing applications in harsh environments or in situations where large numbers of sensors are needed. They are also advantageous in applications where access to the sensor is limited or impossible or when sensors are needed on a disposable basis. Due to their many advantages, LC sensors have been used for sensing a variety of parameters including humidity, temperature, chemical concentrations, pH, stress/pressure, strain, food quality and even biological growth. However, current versions of the LC sensor technology are limited to sensing only one parameter. The purpose of this work is to develop new types of LC sensor systems that are simpler to fabricate (hence lower cost) or capable of monitoring multiple parameters simultaneously. One design presented in this work, referred to as the multi-element LC sensor, is able to measure multiple parameters simultaneously using a second capacitive element. Compared to conventional LC sensors, this design can sense multiple parameters with a higher detection range than two independent sensors while maintaining the same overall sensor footprint. In addition, the two-element sensor does not suffer from interference issues normally encountered while implementing two LC sensors in close proximity. Another design, the single-spiral inductive-capacitive sensor, utilizes the parasitic capacitance of a coil or spring structure to form a single layer LC resonant circuit. Unlike conventional LC sensors, this design is truly planar, thus simplifying its fabrication process and reducing sensor cost. Due to the simplicity of this sensor layout it will be easier and more cost-effective for embedding in common building or packaging materials during manufacturing processes, thereby adding functionality to current products (such as drywall sheets) while having a minor impact on overall unit cost. These modifications to the LC sensor design significantly improve the functionality and commercial feasibility of this technology, especially for applications where a large array of sensors or multiple sensing parameters are required.

Moving Beyond Hastiness and Superficiality: Being an Ethical Technical Communicator via Digital Communication Technologies in Health Care

This thesis examines digital technologies used by technical communicators in healthcare settings. I show that technical communicators, who function as users, advocators and evaluators, need a useable framework for ethical engagement with digital technologies, which integrally affect the physician-patient relationship. Therefore, I apply rhetorical methodology by producing useable knowledge and phenomenological methodology by examining lived experiences of technical communicators. Substantiation comes from theories spanning technical communication, philosophy, and composition studies. Evidence also emerges from qualitative interviews with communication professionals working in healthcare; my concerns arise from personal experiences with electronic recordkeeping in the exam room. This thesis anticipates challenging the presumed theory-practice divide while encouraging greater disciplinary reciprocity. Because technical communication infuses theory into productive capacity, this thesis presents the tripartite summons of the ethical technical communicator: to exercise critically-reflective action that safeguards the physician-patient relationship by ways of using digital technologies, advocating for audiences, and evaluating digital technologies.

ALTERNATING CURRENT DIELECTROPHORETIC MANIPULATION OF ERYTHROCYTES IN MEDICAL MICRODEVICE TECHNOLOGY

Medical microdevices have gained popularity in the past few decades because they allow the medical laboratory to be taken out into the field and for disease diagnostics to happen with a smaller sample volume, at a lower cost and much faster. Blood is the human body's most readily available and informative diagnostic fluid because of the wealth of information it provides about the body's general health including enzymatic, proteomic and immunological states. The purpose of this project is to optimize operating conditions and study ABO-Rh erythrocytes dielectrophoretic responses to alternating current electric signals. The end goal of this project is the creation of a relatively inexpensive microfluidic device, which can be used for the ABO-Rh typing of a blood sample. This dissertation presents results showing how blood samples of a known ABO- Rh blood type exhibit differing behavior to the same electrical stimulus based on their blood type. The first panel of donors and experiments, presented in Chapter 4 occurred when a sample of known blood type was injected into a microdevice with a T-shaped electrode configuration and the erythorcytes were found to rupture at a rate specific to their ABO-Rh blood type. The second set of experiments, presented in Chapter 5, were originally published in Electrophoresis in 20111. Novel in this work was the discovery that treatment of human erythrocytes with β-galactosidase successfully removed ABO surface antigens such that native A and B blood no longer agglutinated with the proper antibodies. This work was performed in a medium of conductivity 0.9S/m which is close to the measured conductivity of pooled plasma (~1.1S/m). The ability to perform dielectrophoresis experiments at physiological conductivities conditions is advantageous for future portable devices because the device/instrument would not need to store dilution buffers. The final results of this project, presented in Chapter 6, explore the entire dielectrophoretic spectra of the ABO-Rh erythrocytes including the cross-over frequency and the magnitudes of the positive or negative dielectrophoretic response. These were completed at lower medium conductivities of 0.1S/m and 0.01-0.04S/m. These results show that by using the sweep function built into the Agilent alternating current generator it is possible to explore how a single group of blood cells will react to rapid changes in frequency and will provide the user with curve that can be matched the theoretical dielectrophoretic response curves. As a whole this project shows that it is possible to distinguish human erythrocytes by their ABO-Rh blood type via three different dielectrophoretic methods. This work builds on the foundation of that it is possible to distinguish healthy from infected cells2-7, similar cell types1,7-14 and other work regarding the dielectrophoresis of human erythrocytes1,10,11. This work has implications in both medical diagnostics and future dielectrophoretic work because it has shown that ABO-Rh blood type is now a factor, which must be identified when working with a human blood sample. It also shows that the creation of a microfluidic device that subjects human erythrocytes to a dielectrophoretic impulse and then exports an ABO-Rh blood type is a near future possibility.

TEACHING MENSTRUAL HEALTH AND HYGIENE TO YOUNG WOMEN IN EASTERN UGANDA WITH REUSABLE MENSTRUAL PADS

In order to identify the impact of teaching menstrual health and hygiene with reusable menstrual pads on knowledge retention and school attendance, qualitative and quantitative data was collected from three rural schools in three districts of eastern Uganda: Amuria, Bukedea, and Ngora. Research techniques employed were preliminary and post surveys of 85 young women; average age 16.9 years. Findings include positive and negative results. Participants’ feelings of normalcy and comfort increased and participants had improved understanding of sexual climax and appropriate menstrual management strategies. There was no statistically significant impact of teaching on topics of sexual intercourse or pregnancy. The impact of reusable menstrual pad sanitary technology on school attendance was negative as more young women reported missing up to a full day of school during their menstrual period (χ2 (3, 73) = 7.81, p = 0.05). Study limitations are discussed and future work is suggested.