Modeling of diesel particulate filter filtration and regeneration for transient driving schedules

Due to their high thermal efficiency, diesel engines have excellent fuel economy and have been widely used as a power source for many vehicles. Diesel engines emit less greenhouse gases (carbon dioxide) compared with gasoline engines. However, diesel engines emit large amounts of particulate matter (PM) which can imperil human health. The best way to reduce the particulate matter is by using the Diesel Particulate Filter (DPF) system which consists of a wall-flow monolith which can trap particulates, and the DPF can be periodically regenerated to remove the collected particulates. The estimation of the PM mass accumulated in the DPF and total pressure drop across the filter are very important in order to determine when to carry out the active regeneration for the DPF. In this project, by developing a filtration model and a pressure drop model, we can estimate the PM mass and the total pressure drop, then, these two models can be linked with a regeneration model which has been developed previously to predict when to regenerate the filter. There results of this project were: 1 Reproduce a filtration model and simulate the processes of filtration. By studying the deep bed filtration and cake filtration, stages and quantity of mass accumulated in the DPF can be estimated. It was found that the filtration efficiency increases faster during the deep-bed filtration than that during the cake filtration. A “unit collector” theory was used in our filtration model which can explain the mechanism of the filtration very well. 2 Perform a parametric study on the pressure drop model for changes in engine exhaust flow rate, deposit layer thickness, and inlet temperature. It was found that there are five primary variables impacting the pressure drop in the DPF which are temperature gradient along the channel, deposit layer thickness, deposit layer permeability, wall thickness, and wall permeability. 3 Link the filtration model and the pressure drop model with the regeneration model to determine the time to carry out the regeneration of the DPF. It was found that the regeneration should be initiated when the cake layer is at a certain thickness, since a cake layer with either too big or too small an amount of particulates will need more thermal energy to reach a higher regeneration efficiency. 4 Formulate diesel particulate trap regeneration strategies for real world driving conditions to find out the best desirable conditions for DPF regeneration. It was found that the regeneration should be initiated when the vehicle’s speed is high and during which there should not be any stops from the vehicle. Moreover, the regeneration duration is about 120 seconds and the inlet temperature for the regeneration is 710K.

Modeling particulate organic matter diagenesis with SED2K

Diagenesis of particulate organic matter in lake sediments consumes and produces chemical species that have significant effects on water quality, e.g. oxygen and nitrate depletion and attendant mediation of nutrient and metal recycling. A mechanistic, mass balance model (SED2K) is applied here in quantifying the time course and magnitude of sediment response to reductions in depositional fluxes of organic matter. In applying the model, direct, site-specific measurements of the sedimentation and POM rates in Onondaga Lake are used, leaving only the diagenesis coefficient (solubilization) for estimation by fit to downcore POM profiles. Model calibration is constrained by the dual requirement that both POM profiles and the time series of efflux of the products of diagenesis must be matched. Simulations point to the existence of POM preservation processes at depth, a phenomenon that may enhance the timing and magnitude of lake recovery.

Gender on the Range: Feminine Strategies in the 1913 Michigan Copper Strike

In the autumn of 1913, a small, remote Michigan mining community attracted national attention as miners and management found themselves embroiled in a conflict that would prove no easy victory for either side. The strike came as a shock to management, who, with the help of a nearly perfected paternal system, had come to expect a generally docile and compliant workforce. But what was even more shocking was the involvement of the miners’ wives in the strike effort, and the lengths they went to in order to keep men from crossing the picket line. This paper focuses on that effort, arguing that the women of the Michigan copper country developed strike strategies that were derived from their domestic experience, and justified their involvement through maternal arguments. However, these public actions allowed the management to disregard the respect and courtesy generally given to the domestic sphere as police and private agents perpetrated a number of home invasions in an attempt to break the strike. The involvement of women in male dominated labor disputes (mining, steel productions) has been largely ignored in the literature due to their indirect connection to the company as wives and not workers. This paper seeks to remedy this gap, and gain a better understanding of that indirect relationship. Sources include newspaper articles, private correspondence, public investigation records, and oral histories, found largely in the Michigan Tech Archives and Copper Country Historical Collections, Michigan Technological University, Michigan.