DESIGN OF A LIQUID FUEL INJECTOR FOR ALTERNATIVE FUEL STUDIES IN AN ATMOSPHERIC MODEL GAS TURBINE COMBUSTOR

A new liquid-fuel injector was designed for use in the atmospheric-pressure, model gas turbine combustor in Bucknell University’s Combustion Research Laboratory during alternative fuel testing. The current liquid-fuel injector requires a higher-than-desired pressure drop and volumetric flow rate to provide proper atomization of liquid fuels. An air-blast atomizer type of fuel injector was chosen and an experiment utilizing water as the working fluid was performed on a variable-geometry prototype. Visualization of the spray pattern was achieved through photography and the pressure drop was measured as a function of the required operating parameters. Experimental correlations were used to estimate droplet sizes over flow conditions similar to that which would be experienced in the actual combustor. The results of this experiment were used to select the desired geometric parameters for the proposed final injector design and a CAD model was generated. Eventually, the new injector will be fabricated and tested to provide final validation of the design prior to use in the combustion test apparatus.

FPGA BASED DESIGN FOR ACCELERATED FAULT-TESTING OF INTEGRATED CIRCUITS

In the past few decades, integrated circuits have become a major part of everyday life. Every circuit that is created needs to be tested for faults so faulty circuits are not sent to end-users. The creation of these tests is time consuming, costly and difficult to perform on larger circuits. This research presents a novel method for fault detection and test pattern reduction in integrated circuitry under test. By leveraging the FPGA's reconfigurability and parallel processing capabilities, a speed up in fault detection can be achieved over previous computer simulation techniques. This work presents the following contributions to the field of Stuck-At-Fault detection: We present a new method for inserting faults into a circuit net list. Given any circuit netlist, our tool can insert multiplexers into a circuit at correct internal nodes to aid in fault emulation on reconfigurable hardware. We present a parallel method of fault emulation. The benefit of the FPGA is not only its ability to implement any circuit, but its ability to process data in parallel. This research utilizes this to create a more efficient emulation method that implements numerous copies of the same circuit in the FPGA. A new method to organize the most efficient faults. Most methods for determinin the minimum number of inputs to cover the most faults require sophisticated softwareprograms that use heuristics. By utilizing hardware, this research is able to process data faster and use a simpler method for an efficient way of minimizing inputs.

A Method for Assessing the Sustainability of Design in Developing World Projects

Projects for the developing world usually find themselves at the bottom of an engineer’s priority list. There is often very little engineering effort placed on creating new products for the poorest people in the world. This trend is beginning to change now as people begin to recognize the potential for these projects. Engineers are beginning to try and solve some of the direst issues in the developing world and many are having positive impacts. However, the conditions needed to support these projects can only be maintained in the short term. There is now a need for greater sustainability. Sustainability has a wide variety of definitions in both business and engineering. These concepts are analyzed and synthesized to develop a broad meaning of sustainability in the developing world. This primarily stems from the “triple bottom line” concept of economic, social, and environmental sustainability. Using this model and several international standards, this thesis develops a metric for guiding and evaluating the sustainability of engineering projects. The metric contains qualitative questions that investigate the sustainability of a project. It is used to assess several existing projects in order to determine flaws. Specifically, three projects seeking to deliver eyeglasses are analyzed for weaknesses to help define a new design approach for achieving better results. Using the metric as a guiding tool, teams designed two pieces of optometry equipment: one to cut lenses for eyeglasses and the other to diagnose refractive error, or prescription. These designs are created and prototyped in the developed and developing worlds in order to determine general feasibility. Although there is a recognized need for eventual design iterations, the whole project is evaluated using the developed metric and compared to the existing projects. Overall, the success demonstrates the improvements made to the long-term sustainability of the project resulting from the use of the sustainability metric.

Adaptive and Maladaptive Correlates of Repetitive Behavior and Restricted Interests in Persons with Down Syndrome and Developmentally-Matched Typical Children: A Two-Year Longitudinal Sequential Design

We examined the course of repetitive behavior and restricted interests (RBRI) in children with and without Down syndrome (DS) over a two-year time period. Forty-two typically-developing children and 43 persons with DS represented two mental age (MA) levels: `` younger'' 2-4 years; `` older'' 5-11 years. For typically developing younger children some aspects of RBRI increased from Time 1 to Time 2. In older children, these aspects remained stable or decreased over the two-year period. For participants with DS, RBRI remained stable or increased over time. Time 1 RBRI predicted Time 2 adaptive behavior (measured by the Vineland Scales) in typically developing children, whereas for participants with DS, Time 1 RBRI predicted poor adaptive outcome (Child Behavior Checklist) at Time 2. The results add to the body of literature examining the adaptive and maladaptive nature of repetitive behavior.

Design Simulation for Solar Energy Research and Education

Solar research is primarily conducted in regions with consistent sunlight, severely limiting research opportunities in many areas. Unfortunately, the unreliable weather in Lewisburg, PA, can prove difficult for such testing to be conducted. As such, a solar simulator was developed for educational purposes for the Mechanical Engineering department at Bucknell University. The objective of this work was to first develop a geometric model to evaluate a one sun solar simulator. This was intended to provide a simplified model that could be used without the necessity of expensive software. This model was originally intended to be validated experimentally, but instead was done using a proven ray tracing program, TracePro. Analyses with the geometrical model and TracePro demonstrated the influence the geometrical properties had results, specifically the reflector (aperture) diameter and the rim angle. Subsequently, the two were approaches were consistent with one another for aperture diameters 0.5 m and larger, and for rim angles larger than 45°. The constructed prototype, that is currently untested, was designed from information provided by the geometric model, includes a metal halide lamp with a 9.5 mm arc diameter and parabolic reflector with an aperture diameter of 0.631 meters. The maximum angular divergence from the geometrical model was predicted to be 30 mRadians. The average angular divergence in TraceProof the system was 19.5 mRadians, compared to the sun’s divergence of 9.2 mRadians. Flux mapping in TracePro showed an intensity of 1000 W/m2 over the target plane located 40 meters from the lamp. The error between spectrum of the metal halide lamp and the solar spectrum was 10.9%, which was found by comparing their respective Plank radiation distributions. The project did not satisfy the original goal of matching the angular divergence of sunlight, although the system could still to be used for optical testing. The geometric model indicated performance in this area could be improved by increasing the diameter of the reflector, as well as decreasing the source diameter. Although ray tracing software provides more information to analyze the simulator system, the geometrical model is adequate to provide enough information to design a system.