Hydraulic Conductivity of Model Soil-Bentonite Backfills Subjected to Wet-Dry Cycling

The potential for changes in hydraulic conductivity, k, of two model soil-bentonite (SB) backfills subjected to wet-dry cycling was investigated. The backfills were prepared with the same base soil (clean, fine sand) but different bentonite contents (2.7 and 5.6 dry wt %). Saturation (S), volume change, and k of consolidated backfill specimens (effective stress = 24 kPa) were evaluated over three to seven cycles in which the matric suction, Ym, in the drying stage ranged from 50 to 700 kPa. Both backfills exhibited susceptibility to degradation in k caused by wet-dry cycling. Mean values of k for specimens dried at Ym = 50 kPa (S = 30-60 % after drying) remained low after two cycles, but increased by 5- to 300-fold after three or more cycles. Specimens dried at Ym ≥ 150 kPa (S < 30 % after drying) were less resilient and exhibited 500- to 10 000-fold increases in k after three or more cycles. The greater increases in k for these specimens correlated with greater vertical shrinkage upon drying. The findings suggest that increases in hydraulic conductivity due to wet-dry cycling may be a concern for SB vertical barriers located within the zone of a fluctuating groundwater table.

Chemical Compatibility of Model Soil-Bentonite Backfill Containing Multiswellable Bentonite

The objective of this study was to evaluate the chemical compatibility of model soil-bentonite backfills containing multiswellable bentonite (MSB) relative to that of similar backfills containing untreated sodium (Na) bentonite or a commercially available, contaminant resistant bentonite (SW101). Flexible-wall tests were conducted on consolidated backfill specimens (effective stress =34.5 kPa) containing clean sand and 4.5–5.7% bentonite (by dry weight) using tap water and calcium chloride (CaCl2) solutions (10–1,000 mM) as the permeant liquids. Final values of hydraulic conductivity (k) and intrinsic permeability (K) to the CaCl2 solutions were determined after achieving both short-term termination criteria as defined by ASTM D5084 and long-term termination criteria for chemical equilibrium between the influent and effluent. Specimens containing MSB exhibited the smallest increases in k and K upon permeation with a given CaCl2 solution relative to specimens containing untreated Na bentonite or SW101. However, none of the specimens exhibited more than a five-fold increase in k or K, regardless of CaCl2 concentration or bentonite type. Final k values for specimens permeated with a given CaCl2 solution after permeation with tap water were similar to those for specimens of the same backfill permeated with only the CaCl2 solution, indicating that the order of permeation had no significant effect on k. Also, final k values for all specimens were within a factor of two of the k measured after achieving the ASTM D5084 termination criteria. Thus, use of only the ASTM D5084 criteria would have been sufficient to obtain reasonable estimates of long-term hydraulic conductivity for the specimens in this study.

DESIGN OF A LIQUID FUEL INJECTOR FOR ALTERNATIVE FUEL STUDIES IN AN ATMOSPHERIC MODEL GAS TURBINE COMBUSTOR

A new liquid-fuel injector was designed for use in the atmospheric-pressure, model gas turbine combustor in Bucknell University’s Combustion Research Laboratory during alternative fuel testing. The current liquid-fuel injector requires a higher-than-desired pressure drop and volumetric flow rate to provide proper atomization of liquid fuels. An air-blast atomizer type of fuel injector was chosen and an experiment utilizing water as the working fluid was performed on a variable-geometry prototype. Visualization of the spray pattern was achieved through photography and the pressure drop was measured as a function of the required operating parameters. Experimental correlations were used to estimate droplet sizes over flow conditions similar to that which would be experienced in the actual combustor. The results of this experiment were used to select the desired geometric parameters for the proposed final injector design and a CAD model was generated. Eventually, the new injector will be fabricated and tested to provide final validation of the design prior to use in the combustion test apparatus.

The Design of XML-Based Model and Experiment Description Languages for Network Simulation

The Simulation Automation Framework for Experiments (SAFE) is a project created to raise the level of abstraction in network simulation tools and thereby address issues that undermine credibility. SAFE incorporates best practices in network simulationto automate the experimental process and to guide users in the development of sound scientific studies using the popular ns-3 network simulator. My contributions to the SAFE project: the design of two XML-based languages called NEDL (ns-3 Experiment Description Language) and NSTL (ns-3 Script Templating Language), which facilitate the description of experiments and network simulationmodels, respectively. The languages provide a foundation for the construction of better interfaces between the user and the ns-3 simulator. They also provide input to a mechanism which automates the execution of network simulation experiments. Additionally,this thesis demonstrates that one can develop tools to generate ns-3 scripts in Python or C++ automatically from NSTL model descriptions.

Challenges of the Cooperative Movement In Addressing Issues of Human Security In the Context of a Neoliberal World: the Case of Argentina

The response of some Argentine workers to the 2001 crisis of neoliberalism gave rise to a movement of worker-recovered enterprises (empresas recuperadas por sus trabajadores or ERTs). The ERTs have emerged as former employees took over the control of generally fraudulently bankrupt factories and enterprises. The analysis of the ERT movement within the neoliberal global capitalist order will draw from William Robinson’s (2004) neo-Gramscian concept of hegemony. The theoretical framework of neo-Gramscian hegemony will be used in exposing the contradictions of capitalism on the global, national, organizational and individual scales and the effects they have on the ERT movement. The ERT movement has demonstrated strong level of resilience, despite the numerous economic, social, political and cultural challenges and limitations it faces as a consequence of the implementation of neoliberalism globally. ERTs have shown that through non-violent protests, democratic principles of management and social inclusion, it is possible to start constructing an alternative social order that is based on the cooperative principles of “honesty, openness, social responsibility and caring for others” (ICA 2007) as opposed to secrecy, exclusiveness, individualism and self-interestedness. In order to meet this “utopian” vision, it is essential to push the limits of the possible within the current social order and broaden the alliance to include the organized members of the working class, such as the members of trade unions, and the unorganized, such as the unemployed and underemployed. Though marginal in number and size, the members of ERTs have given rise to a model that is worth exploring in other countries and regions burdened by the contradictory workings of capitalism. Today, ERTs serve as living proofs that workers too are capable of successfully running businesses, not capitalists alone.

Assessment Of Dynamic Properties Of A Crowd Model For Human-Structure Interaction Modeling

As lightweight and slender structural elements are more frequently used in the design, large scale structures become more flexible and susceptible to excessive vibrations. To ensure the functionality of the structure, dynamic properties of the occupied structure need to be estimated during the design phase. Traditional analysis method models occupants simply as an additional mass; however, research has shown that human occupants could be better modeled as an additional degree-of- freedom. In the United Kingdom, active and passive crowd models are proposed by the Joint Working Group as a result of a series of analytical and experimental research. It is expected that the crowd models would yield a more accurate estimation to the dynamic response of the occupied structure. However, experimental testing recently conducted through a graduate student project at Bucknell University indicated that the proposed passive crowd model might be inaccurate in representing the impact on the structure from the occupants. The objective of this study is to provide an assessment of the validity of the crowd models proposed by JWG through comparing the dynamic properties obtained from experimental testing data and analytical modeling results. The experimental data used in this study was collected by Firman in 2010. The analytical results were obtained by performing a time-history analysis on a finite element model of the occupied structure. The crowd models were created based on the recommendations from the JWG combined with the physical properties of the occupants during the experimental study. During this study, SAP2000 was used to create the finite element models and to implement the analysis; Matlab and ME¿scope were used to obtain the dynamic properties of the structure through processing the time-history analysis results from SAP2000. The result of this study indicates that the active crowd model could quite accurately represent the impact on the structure from occupants standing with bent knees while the passive crowd model could not properly simulate the dynamic response of the structure when occupants were standing straight or sitting on the structure. Future work related to this study involves improving the passive crowd model and evaluating the crowd models with full-scale structure models and operating data.

Development And Use Of A Model To Predict Properties Of Infiltrated Solid Oxide Fuel Cell Anodes

Solid oxide fuel cells (SOFCs) provide a potentially clean way of using energy sources. One important aspect of a functioning fuel cell is the anode and its characteristics (e.g. conductivity). Using infiltration of conductor particles has been shown to be a method for production at lower cost with comparable functionality. While these methods have been demonstrated experimentally, there is a vast range of variables to consider. Because of the long time for manufacture, a model is desired to aid in the development of the desired anode formulation. This thesis aims to (1) use an idealized system to determine the appropriate size and aspect ratio to determine the percolation threshold and effective conductivity as well as to (2) simulate the infiltrated fabrication method to determine the effective conductivity and percolation threshold as a function of ceramic and pore former particle size, particle fraction and the cell¿s final porosity. The idealized system found that the aspect ratio of the cell does not affect the cells functionality and that an aspect ratio of 1 is the most efficient computationally to use. Additionally, at cell sizes greater than 50x50, the conductivity asymptotes to a constant value. Through the infiltrated model simulations, it was found that by increasing the size of the ceramic (YSZ) and pore former particles, the percolation threshold can be decreased and the effective conductivity at low loadings can be increased. Furthermore, by decreasing the porosity of the cell, the percolation threshold and effective conductivity at low loadings can also be increased

Teacher resistance to school-based consultation with the school psychologist: An analysis according to school level and model of identification for special education services

Consultation is promoted throughout school psychology literature as a best practice in service delivery. This method has numerous benefits including being able to work with more students at one time, providing practitioners with preventative rather than strictly reactive strategies, and helping school professionals meet state and federal education mandates and initiatives. Despite the benefits of consultation, teachers are sometimes resistant to this process.This research studies variables hypothesized to lead to resistance (Gonzalez, Nelson, Gutkin, & Shwery, 2004) and attempts to distinguish differences between school level (elementary, middle and high school) with respect to the role played by these variables and to determine if the model used to identify students for special education services has an influence on resistance factors. Twenty-sixteachers in elementary and middle schools responded to a demographicquestionnaire and a survey developed by Gonzalez, et al. (2004). This survey measures eight variables related to resistance to consultation. No high school teachers responded to the request to participate. Results of analysis of variance indicated a significant difference in the teaching efficacy subscale with elementary teachers reporting more efficacy in teaching than middle school teachers. Results also indicate a significant difference in classroom managementefficacy with teachers who work in schools that identify students according to a Response to Intervention model reporting higher classroom management efficacy than teachers who work in schools that identify students according to a combined method of refer-test-place/RtI combination model. Implications, limitations and directions for future research are discussed.

Social Context and Economic Biases in Representation

This article explores the role of political context in shaping economic biases in representation-the degree to which wealthy citizens' views are more strongly represented than poorer citizens' views in the choices of policymakers. I develop a general model that explains why poorer citizens will be better represented relative to the rich in certain political contexts than others, arguing that the relative representation of the poor will be stronger in contexts that make the views of the poor relevant and accessible to policymakers. I then derive several specific hypotheses that flow from this model and test these hypotheses through a study of the dyadic relationships between citizens and their representatives in the U.S. Congress. The results show that poorer citizens are better represented relative to the rich in Congressional districts that are electorally competitive, have low median incomes, have relatively equal distributions of incomes, have a significant organized labor presence, and are represented by Democrats.

The Dual Ownership Structure: a Model to Connect the Cooperative Model With Financial Markets

In business literature, the conflicts among workers, shareholders and the management have been studied mostly in the frame of stakeholder theory. The stakeholder theory recognizes this issue as an agency problem, and tries to solve the problem by establishing a contractual relationship between the agent and principals. However, as Marcoux pointed out, the appropriateness of the contract as a medium to reduce the agency problem should be questioned. As an alternative, the cooperative model minimizes the agency costs by integrating the concept of workers, owners and management. Mondragon Corporation is a successful example of the cooperative model which grew into the sixth largest corporation in Spain. However, the cooperative model has long been ignored in discussions of corporate governance, mainly because the success of the cooperative model is extremely difficult to duplicate in reality. This thesis hopes to revitalize the scholarly examination of cooperatives by developing a new model that overcomes the fundamental problem in the cooperative model: the limited access to capital markets. By dividing the ownership interest into financial and control interest, the dual ownership structure allows cooperatives to issue stock in the capital market by making a financial product out of financial interest.