Reconstruction of a flash flood with large wood transport and its influence on hazard patterns in an ungauged mountain basin

The reconstruction of past flash floods in ungauged basins leads to a high level of uncertainty, which increases if other processes are involved such as the transport of large wood material. An important flash flood occurred in 1997 in Venero Claro (Central Spain), causing significant economic losses. The wood material clogged bridge sections, raising the water level upstream. The aim of this study was to reconstruct this event, analysing the influence of woody debris transport on the flood hazard pattern. Because the reach in question was affected by backwater effects due to bridge clogging, using only high water mark or palaeostage indicators may overestimate discharges, and so other methods are required to estimate peak flows. Therefore, the peak discharge was estimated (123 ± 18 m3 s–1) using indirect methods, but one-dimensional hydraulic simulation was also used to validate these indirect estimates through an iterative process (127 ± 33 m3 s–1) and reconstruct the bridge obstruction to obtain the blockage ratio during the 1997 event (~48%) and the bridge clogging curves. Rainfall–Runoff modelling with stochastic simulation of different rainfall field configurations also helped to confirm that a peak discharge greater than 150 m3 s–1 is very unlikely to occur and that the estimated discharge range is consistent with the estimated rainfall amount (233 ± 27 mm). It was observed that the backwater effect due to the obstruction (water level ~7 m) made the 1997 flood (~35-year return period) equivalent to the 50-year flood. This allowed the equivalent return period to be defined as the recurrence interval of an event of specified magnitude, which, where large woody debris is present, is equivalent in water depth and extent of flooded area to a more extreme event of greater magnitude. These results highlight the need to include obstruction phenomena in flood hazard analysis.

What is ‘wood’ – An anatomical re-definition

The technical definition of ‘wood’ is well accepted, but its botanical understanding remains vague. Different degrees and amounts of lignification in plants and their imprecise description, together with a conceptually doubtful life form catalog including trees, shrubs and herbs further complicate our understanding of ‘wood’. Here, we use permanent micro sections to demonstrate that the xylem and bark of terrestrial plants can vary from one tissue with a few lignified cells to an almost fully lignified tissue. This universal principle of plant growth and stabilization, accounting for all taxonomic units within vascular plants, suggests that the classical life form separation into herbs, shrubs and trees is not valid. An anatomical-based differentiation between ‘wood’, ‘woody’ and ‘woodiness’ is also only meaningful if supplemented by insight on the particular plant section and its lignified proportion. We therefore recommend utilizing the botanically more neutral term ‘stem anatomy’ instead of ‘wood anatomy’, which further implies integration of the xylem and bark of all terrestrial plants. Since dendrochronology considers shrubs, dwarf shrubs and perennial herbs in addition to trees, its semantic expansion toward ‘xylemchronology’ might be worthwhile considering.

Past and future carbon fluxes from land use change, shifting cultivation and wood harvest

Carbon emissions from anthropogenic land use (LU) and land use change (LUC) are quantified with a Dynamic Global Vegetation Model for the past and the 21st century following Representative Concentration Pathways (RCPs). Wood harvesting and parallel abandonment and expansion of agricultural land in areas of shifting cultivation are explicitly simulated (gross LUC) based on the Land Use Harmonization (LUH) dataset and a proposed alternative method that relies on minimum input data and generically accounts for gross LUC. Cumulative global LUC emissions are 72 GtC by 1850 and 243 GtC by 2004 and 27–151 GtC for the next 95 yr following the different RCP scenarios. The alternative method reproduces results based on LUH data with full transition information within <0.1 GtC/yr over the last decades and bears potential for applications in combination with other LU scenarios. In the last decade, shifting cultivation and wood harvest within remaining forests including slash each contributed 19% to the mean annual emissions of 1.2 GtC/yr. These factors, in combination with amplification effects under elevated CO2, contribute substantially to future emissions from LUC in all RCPs.

Sources and contributions of wood smoke during winter in London: assessing local and regional influences

Determining the contribution of wood smoke to air pollution in large cities such as London is becoming increasingly important due to the changing nature of domestic heating in urban areas. During winter, biomass burning emissions have been identified as a major cause of exceedances of European air quality limits. The aim of this work was to quantify the contribution of biomass burning in London to concentrations of PM2:5 and determine whether local emissions or regional contributions were the main source of biomass smoke. To achieve this, a number of biomass burning chemical tracers were analysed at a site within central London and two sites in surrounding rural areas. Concentrations of levoglucosan, elemental carbon (EC), organic carbon (OC) and K+ were generally well correlated across the three sites. At all the sites, biomass burning was found to be a source of OC and EC, with the largest contribution of EC from traffic emissions, while for OC the dominant fraction included contributions from secondary organic aerosols, primary biogenic and cooking sources. Source apportionment of the EC and OC was found to give reasonable estimation of the total carbon from non-fossil and fossil fuel sources based upon comparison with estimates derived from 14C analysis. Aethalometer-derived black carbon data were also apportioned into the contributions frombiomass burning and traffic and showed trends similar to those observed for EC. Mean wood smoke mass at the sites was estimated to range from 0.78 to 1.0 μgm-3 during the campaign in January–February 2012. Measurements on a 160m tower in London suggested a similar ratio of brown to black carbon (reflecting wood burning and traffic respectively) in regional and London air. Peaks in the levoglucosan and K+ concentrations were observed to coincide with low ambient temperature, consistent with domestic heating as a major contributing local source in London. Overall, the source of biomass smoke in London was concluded to be a background regional source overlaid by contributions from local domestic burning emissions. This could have implications when considering future emission control strategies during winter and may be the focus of future work in order to better determine the contributing local sources.

Comparison of several wood smoke markers and source apportionment methods for wood burning particulate mass

Residential wood combustion has only recently been recognized as a major contributor to air pollution in Switzerland and in other European countries. A source apportionment method using the aethalometer light absorption parameters was applied to five winter campaigns at three sites in Switzerland: a village with high wood combustion activity in winter, an urban background site and a highway site. The particulate mass from traffic (PMtraffic) and wood burning (PMwb) emissions obtained with this model compared fairly well with results from the 14C source apportionment method. PMwb from the model was also compared to well known wood smoke markers such as anhydrosugars (levoglucosan and mannosan) and fine mode potassium, as well as to a marker recently suggested from the Aerodyne aerosol mass spectrometer (mass fragment m/z 60). Additionally the anhydrosugars were compared to the 14C results and were shown to be comparable to literature values from wood burning emission studies using different types of wood (hardwood, softwood). The levoglucosan to PMwb ratios varied much more strongly between the different campaigns (4–13%) compared to mannosan to PMwb with a range of 1–1.5%. Possible uncertainty aspects for the various methods and markers are discussed.

Long-distance spore dispersal in wood-inhabiting Basidiomycetes

Eight species of wood-inhabiting basidiomycetes (Laurilia sulcata, Peniophora aurantiaca, Resinicium bicolor, Scytinostroma galactinum, Terana caerulea, Trichaptum abietinum, T. biforme and T. fuscoviolaceum) were used in a spore-trapping test to evaluate their individual ability for long-distance spore dispersal. Petri dishes with single spore mycelia were used as baits. In the experiment, carried out at the Botanical Institute in Göteborg, spores from the air were regularly captured. Surprisingly, spores were captured from species whose nearest known natural occurrence was located quite far from Göteborg. The closest population of Peniophora aurantiaca is about 1000 km south of Göteborg. The results from this experiment support the hypothesis that fungal spores are widely and efficiently dispersed. Such a broad and extensive dispersal ability is of vital importance, especially for wood-inhabiting species which are highly dependent on a substrate which is onlv temporarily available.

Adjusting mortality for loss to follow-up: analysis of five ART programmes in sub-Saharan Africa

Evaluation of antiretroviral treatment (ART) programmes in sub-Saharan Africa is difficult because many patients are lost to follow-up. Outcomes in these patients are generally unknown but studies tracing patients have shown mortality to be high. We adjusted programme-level mortality in the first year of antiretroviral treatment (ART) for excess mortality in patients lost to follow-up.

Early mortality and loss to follow-up in HIV-infected children starting antiretroviral therapy in Southern Africa

Many HIV-infected children in Southern Africa have been started on antiretroviral therapy (ART), but loss to follow up (LTFU) can be substantial. We analyzed mortality in children retained in care and in all children starting ART, taking LTFU into account.

Mortality associated with discordant responses to antiretroviral therapy in resource-constrained settings

Objectives: We assessed mortality associated with immunologic and virologic patterns of response at 6 months of highly active antiretroviral therapy (HAART) in HIV-infected individuals from resource-limited countries in Africa and South America. Methods: Patients who initiated HAART between 1996 and 2007, aged 16 years or older, and had at least 1 measurement (HIV-1 RNA plasma viral load or CD4 cell count) at 6 months of therapy (3-9 month window) were included. Therapy response was categorized as complete, discordant (virologic only or immunologic only), and absent. Associations between 6-month response to therapy and all-cause mortality were assessed by Cox proportional hazards regression. Robust standard errors were calculated to account for intrasite correlation. Results: A total of 7160 patients, corresponding to 15,107 person-years, were analyzed. In multivariable analysis adjusted for age at HAART initiation, baseline clinical stage and CD4 cell count, year of HAART initiation, clinic, occurrence of an AIDS-defining condition within the first 6 months of treatment, and discordant and absent responses were associated with increased risk of death. Conclusions: Similar to reports from high-income countries, discordant immunologic and virologic responses were associated with intermediate risk of death compared with complete and no response in this large cohort of HIV-1 patients from resource-limited countries. Our results support a recommendation for wider availability of plasma viral load testing to monitor antiretroviral therapy in these settings.

Bonding of restorative materials to dentin with various luting agents

The aim was to compare eight types of luting agents when used to bond six indirect, laboratory restorative materials to dentin. Cylinders of the six restorative materials (Esteticor Avenir [gold alloy], Tritan [titanium], NobelRondo [feldspathic porcelain], Finesse All-Ceramic [leucite-glass ceramic], Lava [zirconia], and Sinfony [resin composite]) were ground and air-abraded. Cylinders of feldspathic porcelain and glass ceramic were additionally etched with hydrofluoric acid and were silane-treated. The cylinders were luted to ground human dentin with eight luting agents (DeTrey Zinc [zinc phosphate cement], Fuji I [conventional glass ionomer cement], Fuji Plus [resin-modified glass ionomer cement], Variolink II [conventional etch-and-rinse resin cement], Panavia F2.0 and Multilink [self-etch resin cements], and RelyX Unicem Aplicap and Maxcem [self-adhesive resin cements]). After water storage at 37°C for one week, the shear bond strength of the specimens (n=8/group) was measured, and the fracture mode was stereomicroscopically examined. Bond strength data were analyzed with two-factorial analysis of variance (ANOVA) followed by Newman-Keuls' Multiple Range Test (?=0.05). Both the restorative material and the luting agent had a significant effect on bond strength, and significant interaction was noted between the two variables. Zinc phosphate cement and glass ionomer cements produced the lowest bond strengths, whereas the highest bond strengths were found with the two self-etch and one of the self-adhesive resin cements. Generally, the fracture mode varied markedly with the restorative material. The luting agents had a bigger influence on bond strength between restorative materials and dentin than was seen with the restorative material.

Development of a novel fMRI compatible visual perception prototype battery to test older people with and without dementia

Background: Visuoperceptual deficits in dementia are common and can reduce quality of life. Testing of visuoperceptual function is often confounded by impairments in other cognitive domains and motor dysfunction. We aimed to develop, pilot, and test a novel visuocognitive prototype test battery which addressed these issues, suitable for both clinical and functional imaging use. Methods: We recruited 23 participants (14 with dementia, 6 of whom had extrapyramidal motor features, and 9 age-matched controls). The novel Newcastle visual perception prototype battery (NEVIP-B-Prototype) included angle, color, face, motion and form perception tasks, and an adapted response system. It allows for individualized task difficulties. Participants were tested outside and inside the 3T functional magnetic resonance imaging (fMRI) scanner. Functional magnetic resonance imaging data were analyzed using SPM8. Results: All participants successfully completed the task inside and outside the scanner. Functional magnetic resonance imaging analysis showed activation regions corresponding well to the regional specializations of the visual association cortex. In both groups, there was significant activity in the ventral occipital-temporal region in the face and color tasks, whereas the motion task activated the V5 region. In the control group, the angle task activated the occipitoparietal cortex. Patients and controls showed similar levels of activation, except on the angle task for which occipitoparietal activation was lower in patients than controls. Conclusion: Distinct visuoperceptual functions can be tested in patients with dementia and extrapyramidal motor features when tests use individualized thresholds, adapted tasks, and specialized response systems.

Correcting mortality for loss to follow-up: a nomogram applied to antiretroviral treatment programmes in sub-Saharan Africa

Background The World Health Organization estimates that in sub-Saharan Africa about 4 million HIV-infected patients had started antiretroviral therapy (ART) by the end of 2008. Loss of patients to follow-up and care is an important problem for treatment programmes in this region. As mortality is high in these patients compared to patients remaining in care, ART programmes with high rates of loss to follow-up may substantially underestimate mortality of all patients starting ART. Methods and Findings We developed a nomogram to correct mortality estimates for loss to follow-up, based on the fact that mortality of all patients starting ART in a treatment programme is a weighted average of mortality among patients lost to follow-up and patients remaining in care. The nomogram gives a correction factor based on the percentage of patients lost to follow-up at a given point in time, and the estimated ratio of mortality between patients lost and not lost to follow-up. The mortality observed among patients retained in care is then multiplied by the correction factor to obtain an estimate of programme-level mortality that takes all deaths into account. A web calculator directly calculates the corrected, programme-level mortality with 95% confidence intervals (CIs). We applied the method to 11 ART programmes in sub-Saharan Africa. Patients retained in care had a mortality at 1 year of 1.4% to 12.0%; loss to follow-up ranged from 2.8% to 28.7%; and the correction factor from 1.2 to 8.0. The absolute difference between uncorrected and corrected mortality at 1 year ranged from 1.6% to 9.8%, and was above 5% in four programmes. The largest difference in mortality was in a programme with 28.7% of patients lost to follow-up at 1 year. Conclusions The amount of bias in mortality estimates can be large in ART programmes with substantial loss to follow-up. Programmes should routinely report mortality among patients retained in care and the proportion of patients lost. A simple nomogram can then be used to estimate mortality among all patients who started ART, for a range of plausible mortality rates among patients lost to follow-up.