Macro Monte Carlo for dose calculation of proton beams

Although the Monte Carlo (MC) method allows accurate dose calculation for proton radiotherapy, its usage is limited due to long computing time. In order to gain efficiency, a new macro MC (MMC) technique for proton dose calculations has been developed. The basic principle of the MMC transport is a local to global MC approach. The local simulations using GEANT4 consist of mono-energetic proton pencil beams impinging perpendicularly on slabs of different thicknesses and different materials (water, air, lung, adipose, muscle, spongiosa, cortical bone). During the local simulation multiple scattering, ionization as well as elastic and inelastic interactions have been taken into account and the physical characteristics such as lateral displacement, direction distributions and energy loss have been scored for primary and secondary particles. The scored data from appropriate slabs is then used for the stepwise transport of the protons in the MMC simulation while calculating the energy loss along the path between entrance and exit position. Additionally, based on local simulations the radiation transport of neutrons and the generated ions are included into the MMC simulations for the dose calculations. In order to validate the MMC transport, calculated dose distributions using the MMC transport and GEANT4 have been compared for different mono-energetic proton pencil beams impinging on different phantoms including homogeneous and inhomogeneous situations as well as on a patient CT scan. The agreement of calculated integral depth dose curves is better than 1% or 1 mm for all pencil beams and phantoms considered. For the dose profiles the agreement is within 1% or 1 mm in all phantoms for all energies and depths. The comparison of the dose distribution calculated using either GEANT4 or MMC in the patient also shows an agreement of within 1% or 1 mm. The efficiency of MMC is up to 200 times higher than for GEANT4. The very good level of agreement in the dose comparisons demonstrate that the newly developed MMC transport results in very accurate and efficient dose calculations for proton beams.

Neonatal macrocephaly: cerebral primitive neuroectodermal tumor or neuroblastoma as an infrequent cause--a case report and review of the literature

We report a male term newborn presenting with a congenital macrocephaly 3.5 standard deviations above the median, with a wide and tense anterior fontanel, splayed calvarial sutures, and muscular hypotonia. Antenatal head circumferences were repeatedly below the median. A postnatal head ultrasound showed a large right intracerebral mass with right lateral ventricle compression, right temporal horn dilation, and right frontal horn enlargement with lateral displacement. Additional imaging by computed tomography scan and magnetic resonance imaging was performed. A decompression was performed and histology, immunohistochemistry, and molecular biology supported the diagnosis of a primitive neuroectodermal tumor. A MYCN gene amplification assay remained negative. The incidence of neonatal brain tumors is between 1.4 and 4.1/100,000 live births. Their most common presentation is macrocephaly, hydrocephalus, stillbirth, or diagnosis by pre- or postnatal imaging. Although hydrocephaly and intra- or extracranial hemorrhage are the most frequent causes of congenital macrocephaly, this should be initially investigated by head ultrasound. A suspected malignancy will be confirmed by histopathology, immunohistochemistry, and molecular biology.

Intraoperative determination of the load-displacement behavior of scoliotic spinal motion segments: preliminary clinical results

Introduction: Spinal fusion is a widely and successfully performed strategy for the treatment of spinal deformities and degenerative diseases. The general approach has been to stabilize the spine with implants so that a solid bony fusion between the vertebrae can develop. However, new implant designs have emerged that aim at preservation or restoration of the motion of the spinal segment. In addition to static, load sharing principles, these designs also require a profound knowledge of kinematic and dynamic properties to properly characterise the in vivo performance of the implants. Methods: To address this, an apparatus was developed that enables the intraoperative determination of the load–displacement behavior of spinal motion segments. The apparatus consists of a sensor-equipped distractor to measure the applied force between the transverse processes, and an optoelectronic camera to track the motion of vertebrae and the distractor. In this intraoperative trial, measurements from two patients with adolescent idiopathic scoliosis with right thoracic curves were made at four motion segments each. Results: At a lateral bending moment of 5 N m, the mean flexibility of all eight motion segments was 0.18 ± 0.08°/N m on the convex side and 0.24 ± 0.11°/N m on the concave side. Discussion: The results agree with published data obtained from cadaver studies with and without axial preload. Intraoperatively acquired data with this method may serve as an input for mathematical models and contribute to the development of new implants and treatment strategies.