Disorganization and timing of motor behavior : insight from gesture impairments and movement patterns in schizophrenia

Background: Motor symptoms are frequent phenomena across the entire course of schizophrenia1. Some have argued that disorganized behavior was associated with aberrant motor behavior. We have studied the association of motor disturbances and disorganization in two projects focusing on the timing of movements. Method: In two studies, we assessed motor behavior and psychopathology. The first study applied a validated test of upper limb apraxia in 30 schizophrenia patients2,3. We used standardized video assessments of hand gestures by a blinded rater. The second study tested the stability of movement patterns using time series analysis in actigraphy data of 100 schizophrenia patients4. Both stability of movement patterns and the overall amount of movement were calculated from data of two hours with high degrees of social interaction comparable across the 100 subjects. Results: In total, 67% of the patients had gesture performance deficits3. Most frequently, they made spatial, temporal and body-part-as-object errors. Gesture performance relied on frontal lobe function2. Poor gesture performance was associated with increased disorganization scores. In the second study, we found disorganization to be predicted only by more irregular movement patterns irrespective of the overall amount of movement4. Conclusion : Both studies provide evidence for a link between aberrant timing of motor behavior and disorganization. Disturbed movement control seems critical for disorganized behavior in schizophrenia.

Increment thickness versus dentin bond strength of bulk fill flowables

Objectives: The aim was to investigate the influence of increment thickness on shear bond strength (SBS) to dentin of a conventional and two bulk fill flowable composites. Methods: A total of 135 specimens of ground human dentin were produced (n=15/group; 3 increment thicknesses; 3 flowable composites) and the dentin surfaces were treated with the adhesive system OptiBond FL (Kerr) according to manufacturer’s instructions. Split Teflon molds (inner diameter: 3.6 mm) of 2 mm, 4 mm, or 6 mm height allowing three increment thicknesses were clamped on the dentin surfaces and filled with either the conventional flowable Filtek Supreme XTE ((XTE); 3M ESPE) or the bulk fill flowables Filtek Bulk Fill ((FBF); 3M ESPE) or SDR ((SDR); DENTSPLY Caulk). The flowable composites were light-cured for 20 s (Demi LED; Kerr) and the specimens stored for 24 h (37°C, 100% humidity). Specimens were then subjected to a SBS-test in a universal testing machine at a cross-head speed of 1 mm/min (Zwick Z010; Zwick GmbH & Co.). SBS-values were statistically analysed with a nonparametrical ANOVA followed by exact Wilcoxon rank sum tests (α=0.05). Failure mode of the specimens was determined under a stereomicroscope at 25× magnification. Results: SBS-values (MPa) at 2 mm/4 mm/6 mm increment thicknesses (mean value [standard deviation]) were for XTE: 18.8 [2.6]/17.6 [1.6]/16.7 [3.1], for FBF: 20.6 [2.7]/17.8 [2.7]/18.7 [2.9], and for SDR: 21.7 [2.6]/18.5 [2.6]/20.3 [3.0]. For all three flowable composites, 2 mm increments yielded the highest SBS-values whereas for increments of 4 mm and 6 mm no differences were detected. All specimens presented failure modes involving cohesive failure in dentin. Conclusion: The influence of increment thickness on dentin SBS was less pronounced than expected. However, the high number of cohesive failures in dentin, reflecting the efficiency of the adhesive system, suggests a limited discriminatory power of the SBS-test.

Synchronous Holocene climatic oscillations recorded on the Swiss Plateau and at timberline in the Alps

Eight synchronous pre-Roman cold phases were found at 9600–9200, 8600–8150, 7550–6900, 6600– 6200, 5350–4900, 4600–4400, 3500–3200 and 2600–2350 radiocarbon years BP by reconstructing past climate at two sites on the Swiss Plateau and at timberline in the Alps. The cooling events during the early-and mid-Holocene represent temperature values similar to today, and apparently the onset of cooling events represents a deviation from today's mean annual temperature of about 1°C and is triggered at a 1000-year periodicity. At Wallisellen-Langachermoos (440 m), a former oligotrophic lake near Zürich, the correlation between sum mertime lake levels and the seed production of the amphi-Atlantic aquatic plantNajas flexilis was used to reconstruct lake levels over a 3000-year period during the first part of the Holocene. At Lake Seedorf on the western Swiss Plateau (609 m) the sedimentological, palynological and macrofossil record revealed fluctuations of lake levels for the complete Holocene. From Lago Basso in the southern Alps (2250 m, Val San Giacomo near Splügen Pass, Northern Italy) the terrestrial plant macrofossils – especiallyPinus cembra andLarix – allowed the reconstruction of timberline fluctuations controlled by climate. A similar climatic pattern was found at Gouillé Rion pond in the central Swiss Alps (2343 m, Val d'Hérémence) with plant macrofossils and pollen concentrations and percentages. We postulate that these climatic events are detectable throughout central Europe by independent methods in combination with precise AMS-radiocarbon datings on terrestrial plant remains. Our data fit other proxy records of regional climatic change, such as cool intervals from Greenland ice cores, glacier movements in the Swiss and Austrian Alps, and dendro-densitometry on subfossil wood, as well as the palaeoclimatic data from the Jura Mountains of France obtained by sedimentological analyses. Thus our data indicate that the Northern Hemisphere climate was less stable during the Holocene than previously believed.

Output processing and automatic reporting with Stata

This talk illustrates how results from various Stata commands can be processed efficiently for inclusion in customized reports. A two-step procedure is proposed in which results are gathered and archived in the first step and then tabulated in the second step. Such an approach disentangles the tasks of computing results (which may take long) and preparing results for inclusion in presentations, papers, and reports (which you may have to do over and over). Examples using results from model estimation commands and various other Stata commands such as tabulate, summarize, or correlate are presented. Users will also be shown how to dynamically link results into word processors or into LaTeX documents.