Towards End-User Driven Power Saving Control in Android devices

Abstract. During the last decade mobile communications increasingly became part of people's daily routine. Such usage raises new challenges regarding devices' battery lifetime management when using most popular wireless access technologies, such as IEEE 802.11. This paper investigates the energy/delay trade-off of using an end-user driven power saving approach, when compared with the standard IEEE 802.11 power saving algorithms. The assessment was conducted in a real testbed using an Android mobile phone and high-precision energy measurement hardware. The results show clear energy benefits of employing user-driven power saving techniques, when compared with other standard approaches.

Yellow laser light generation by frequency doubling of the output from a master oscillator fiber power amplifier system

We present a power-scalable approach for yellow laser-light generation based on standard Ytterbium (Yb) doped fibers. To force the cavity to lase at 1154 nm, far above the gain-maximum, measures must be taken to fulfill lasing condition and to suppress competing amplified spontaneous emission (ASE) in the high-gain region. To prove the principle we built a fiber-laser cavity and a fiber-amplifier both at 1154 nm. In between cavity and amplifier we suppressed the ASE by 70 dB using a fiber Bragg grating (FBG) based filter. Finally we demonstrated efficient single pass frequency doubling to 577 nm with a periodically poled lithium niobate crystal (PPLN). With our linearly polarized 1154 nm master oscillator power fiber amplifier (MOFA) system we achieved slope efficiencies of more than 15 % inside the cavity and 24 % with the fiber-amplifier. The frequency doubling followed the predicted optimal efficiency achievable with a PPLN crystal. So far we generated 1.5 W at 1154nm and 90 mW at 577 nm. Our MOFA approach for generation of 1154 nm laser radiation is power-scalable by using multi-stage amplifiers and large mode-area fibers and is therefore very promising for building a high power yellow laser-light source of several tens of Watt.

Reporting Experiments in Homeopathic Basic Research—Description of the Checklist Development

The objective of this study was to develop a criteria catalogue serving as a guideline for authors to improve quality of reporting experiments in basic research in homeopathy. A Delphi Process was initiated including three rounds of adjusting and phrasing plus two consensus conferences. European researchers who published experimental work within the last 5 years were involved. A checklist for authors provide a catalogue with 23 criteria. The “Introduction” should focus on underlying hypotheses, the homeopathic principle investigated and state if experiments are exploratory or confirmatory. “Materials and methods” should comprise information on object of investigation, experimental setup, parameters, intervention and statistical methods. A more detailed description on the homeopathic substances, for example, manufacture, dilution method, starting point of dilution is required. A further result of the Delphi process is to raise scientists' awareness of reporting blinding, allocation, replication, quality control and system performance controls. The part “Results” should provide the exact number of treated units per setting which were included in each analysis and state missing samples and drop outs. Results presented in tables and figures are as important as appropriate measures of effect size, uncertainty and probability. “Discussion” in a report should depict more than a general interpretation of results in the context of current evidence but also limitations and an appraisal of aptitude for the chosen experimental model. Authors of homeopathic basic research publications are encouraged to apply our checklist when preparing their manuscripts. Feedback is encouraged on applicability, strength and limitations of the list to enable future revisions.

Simultaneous stable isotope analysis of methane and nitrous oxide on ice core samples

Methane and nitrous oxide are important greenhouse gases which show a strong increase in atmospheric mixing ratios since pre-industrial time as well as large variations during past climate changes. The understanding of their biogeochemical cycles can be improved using stable isotope analysis. However, high-precision isotope measurements on air trapped in ice cores are challenging because of the high susceptibility to contamination and fractionation. Here, we present a dry extraction system for combined CH4 and N2O stable isotope analysis from ice core air, using an ice grating device. The system allows simultaneous analysis of δD(CH4) or δ13C(CH4), together with δ15N(N2O), δ18O(N2O) and δ15N(NO+ fragment) on a single ice core sample, using two isotope mass spectrometry systems. The optimum quantity of ice for analysis is about 600 g with typical "Holocene" mixing ratios for CH4 and N2O. In this case, the reproducibility (1σ ) is 2.1‰ for δD(CH4), 0.18‰ for δ13C(CH4), 0.51‰ for δ15N(N2O), 0.69‰ for δ18O(N2O) and 1.12‰ for δ15N(NO+ fragment). For smaller amounts of ice the standard deviation increases, particularly for N2O isotopologues. For both gases, small-scale intercalibrations using air and/or ice samples have been carried out in collaboration with other institutes that are currently involved in isotope measurements of ice core air. Significant differences are shown between the calibration scales, but those offsets are consistent and can therefore be corrected for.

Scientists’ situated knowledge: Strong objectivity in transdisciplinarity

Although transdisciplinary research has started addressing important epistemological challenges, as evidenced by the discussion about ‘mode 2’ knowledge production, its relation with postulations of ‘scientific objectivity’ is not yet well clarified. A common way of dealing with the epistemological challenge of situated knowledge production, as proposed by transdisciplinarity, is to point to the fundamental aspect of reflexivity. But reflexivity also includes being aware that power and control over the object is derived from the social position of researchers, an issue not often explicitly discussed in transdisciplinary research. Reflexivity thus represents an important but insufficient principle for guaranteeing appropriate levels of self-reflection within a process of knowledge coproduction. We therefore hypothesize that transdisciplinary research could greatly benefit from feminist scientific tradition, in particular the insights of standpoint theory and the concept of ‘strong objectivity’. We analyse, and reflect upon, how a recent transdisciplinary research initiative – conducted together with civil society organizations in (CSOs) in six countries: Bangladesh, Bolivia, Brazil, Burkina Faso, Ecuador and India – has benefited from the use of ‘strong objectivity’. We analyse how the social position of all stakeholders, including ourselves as the scientific actors in this initiative, influence the process and conditions of transdisciplinary knowledge co-production, and we discuss how power and control by scientists affects the process and conditions of interaction. Thereby we argue for the necessity of explicitly assuming sides in contested contexts for reaching objectivity in transdisciplinary research.

Robust indoor localization of narrowband signals

Many location-based services target users in indoor environments. Similar to the case of dense urban areas where many obstacles exist, indoor localization techniques suffer from outlying measurements caused by severe multipath propaga??tion and non-line-of-sight (NLOS) reception. Obstructions in the signal path caused by static or mobile objects downgrade localization accuracy. We use robust multipath mitigation techniques to detect and filter out outlying measurements in indoor environments. We validate our approach using a power-based lo??calization system with GSM. We conducted experiments without any prior knowledge of the tracked device's radio settings or the indoor radio environment. We obtained localization errors in the range of 3m even if the sensors had NLOS links to the target device.