Operator variability using different polishing methods and surface geometry of a nanohybrid composite

This study evaluated the operator variability of different finishing and polishing techniques. After placing 120 composite restorations (Tetric EvoCeram) in plexiglassmolds, the surface of the specimens was roughened in a standardized manner. Twelve operators with different experience levels polished the specimens using the following finishing/polishing procedures: method 1 (40 ?m diamond [40D], 15 ?m diamond [15D], 42 ?m silicon carbide polisher [42S], 6 ?m silicon carbide polisher [6S] and Occlubrush [O]); method 2 (40D, 42S, 6S and O); method 3 (40D, 42S, 6S and PoGo); method 4 (40D, 42S and PoGo) and method 5 (40D, 42S and O). The mean surface roughness (Ra) was measured with a profilometer. Differences between the methods were analyzed with non-parametric ANOVA and pairwise Wilcoxon signed rank tests (?=0.05). All the restorations were qualitatively assessed using SEM. Methods 3 and 4 showed the best polishing results and method 5 demonstrated the poorest. Method 5 was also most dependent on the skills of the operator. Except for method 5, all of the tested procedures reached a clinically acceptable surface polish of Ra?0.2 ?m. Polishing procedures can be simplified without increasing variability between operators and without jeopardizing polishing results.

[Oral medicine: a specialty placed between medicine and dentistry]

Oral medicine is a dental specialty that bridges the traditional areas of health between dentistry and medicine. International descriptions reflect this and oral medicine is defined as "the dental speciality placed at the interface between medicine and dentistry and is concerned with the diagnosis and management of (non-dental) pathology affecting the oral and maxillofacial region." Oral medicine specialists provide clinical care to patients with a wide variety of orofacial conditions, including oral mucosal diseases, orofacial pain syndromes, salivary gland disorders, and oral manifestations of systemic diseases. There is a growing need to implement this specialty globally: due to the rapid progress in both medicine and dentistry, and to the growing percentage of senior citizens in many countries, the adequate diagnosis and treatment of oral diseases will become even more complex in the future. In this article, the authors' intention is to point out that oral medicine is neither a recognized specialty nor a distinct field of study in Germany, Austria, or Switzerland; thus, the need for postgraduate training in this field in countries where oral medicine is not a specialization is emphasized.

Minimization of Intra-Operative Shaping of Orthopaedic Fixation Plates: A Population-Based Design

In this paper we present a new population-based method for the design of bone fixation plates. Standard pre-contoured plates are designed based on the mean shape of a certain population. We propose a computational process to design implants while reducing the amount of required intra-operative shaping, thus reducing the mechanical stresses applied to the plate. A bending and torsion model was used to measure and minimize the necessary intra-operative deformation. The method was applied and validated on a population of 200 femurs that was further augmented with a statistical shape model. The obtained results showed substantial reduction in the bending and torsion needed to shape the new design into any bone in the population when compared to the standard mean-based plates.

Comparison of pre-operative dGEMRIC imaging with intra-operative findings in femoroacetabular impingement: preliminary findings

To study standard MRI and dGEMRIC in patients with symptomatic FAI undergoing surgical intervention and compare them with intra-operative findings to see if they were corroborative.

Influence of Surface Roughness on Mechanical Properties of Two Computer-aided Design/Computer-aided Manufacturing (CAD/CAM) Ceramic Materials

SUMMARY The aim of this study was to evaluate the influence of surface roughness on surface hardness (Vickers; VHN), elastic modulus (EM), and flexural strength (FLS) of two computer-aided design/computer-aided manufacturing (CAD/CAM) ceramic materials. One hundred sixty-two samples of VITABLOCS Mark II (VMII) and 162 samples of IPS Empress CAD (IPS) were ground according to six standardized protocols producing decreasing surface roughnesses (n=27/group): grinding with 1) silicon carbide (SiC) paper #80, 2) SiC paper #120, 3) SiC paper #220, 4) SiC paper #320, 5) SiC paper #500, and 6) SiC paper #1000. Surface roughness (Ra/Rz) was measured with a surface roughness meter, VHN and EM with a hardness indentation device, and FLS with a three-point bending test. To test for a correlation between surface roughness (Ra/Rz) and VHN, EM, or FLS, Spearman rank correlation coefficients were calculated. The decrease in surface roughness led to an increase in VHN from (VMII/IPS; medians) 263.7/256.5 VHN to 646.8/601.5 VHN, an increase in EM from 45.4/41.0 GPa to 66.8/58.4 GPa, and an increase in FLS from 49.5/44.3 MPa to 73.0/97.2 MPa. For both ceramic materials, Spearman rank correlation coefficients showed a strong negative correlation between surface roughness (Ra/Rz) and VHN or EM and a moderate negative correlation between Ra/Rz and FLS. In conclusion, a decrease in surface roughness generally improved the mechanical properties of the CAD/CAM ceramic materials tested. However, FLS was less influenced by surface roughness than expected.

E.A.O. guidelines for the use of diagnostic imaging in implant dentistry 2011. A consensus workshop organized by the European Association for Osseointegration at the Medical University of Warsaw

Diagnostics imaging is an essential component of patient selection and treatment planning in oral rehabilitation by means of osseointegrated implants. In 2002, the EAO produced and published guidelines on the use of diagnostic imaging in implant dentistry. Since that time, there have been significant developments in both the application of cone beam computed tomography as well as in the range of surgical and prosthetic applications that can potentially benefit from its use. However, medical exposure to ionizing radiation must always be justified and result in a net benefit to the patient. The as low a dose as is reasonably achievable principle must also be applied taking into account any alternative techniques that might achieve the same objectives. This paper reports on current EAO recommendations arising from a consensus meeting held at the Medical University of Warsaw (2011) to update these guidelines. Radiological considerations are detailed, including justification and optimization, with a special emphasis on the obligations that arise for those who prescribe or undertake such investigations. The paper pays special attention to clinical indications and radiographic diagnostic considerations as well as to future developments and trends.

[The image of dentistry. Part 2: The ideal dentist]

Our second part of the publication entitled "The image of Dentistry" discusses the properties that correspond to the ideal image of dentistry or even the ideal scientist such as the management of the dental practice, the dentist-patient relationship and the appropriate handling of the patient's emotions such as anxiety or pain. The quality of treatment and the friendly, honest and compassionate attitude of the dentist can immediately affect the image of dentistry. Therefore, the dental professional must try to keep the balance between practice profit, staffing and patient well-being in order to fulfill both social and public health responsibilities.

Antinociceptive activity of pre- versus post-operative intra-articular bupivacaine in goats undergoing stifle arthrotomy

OBJECTIVE: To evaluate the peri-operative analgesic efficacy of intra-articular bupivacaine administered before or after stifle arthrotomy. STUDY DESIGN: Prospective, randomized, blind, placebo-controlled experimental trial. ANIMALS: Thirty-nine healthy goats. METHODS: The goats were allocated randomly to one of three intra-articular treatment groups: group PRE (bupivacaine before and saline after surgery), group POST (saline before and bupivacaine after surgery) and group CON (saline before and after surgery). Anaesthesia was maintained with a constant end-tidal sevoflurane of 2.5%. Intra-operatively heart rate (HR), respiratory rate and mean arterial blood pressure (MAP) after critical surgical events (CSE) were recorded and compared with pre-incision values. Propofol requirements to maintain surgical anaesthesia were recorded. Flunixin was administered for 5 days. Post-operative pain assessment at 20 minutes, 2 hours, 4 hours after recovery and on day 2 and 3 included a multidimensional pain score (MPS), a lameness score and mechanical nociceptive threshold (MNT) testing. Rescue analgesia consisted of systemic opioids. Data were analysed using Kruskal-Wallis, Mann-Whitney, Friedman or chi-square tests as appropriate. RESULTS: Intra-operatively, group PRE had lower HR and MAP at several CSEs than groups POST/CON and required less propofol [0 mg kg(-1) (0-0 mg kg(-1))] than group POST/CON [0.3 mg kg(-1) (0-0.6 mg kg(-1))]. Post-operatively, group POST had significantly higher peri-articular MNTs than groups PRE and CON up to 4 hours after recovery. No treatment effect was detected for MPS, lameness scores and rescue analgesic consumption at any time point. CONCLUSIONS AND CLINICAL RELEVANCE: Pre-operative intra-articular bupivacaine provided notable intra-operative analgesia in goats undergoing stifle arthrotomy but did not reduce post-operative pain. Post-operative intra-articular bupivacaine provided a short lasting reduction of peri-articular hyperalgesia without affecting the requirements for systemic analgesia. Multimodal perioperative pain therapy is recommended to provide adequate analgesia for stifle arthrotomy in goats.

Long-term outcome of ablative therapy of post-operative atrial tachyarrhythmias in patients with tetralogy of Fallot: a European multi-centre study

Post-operative atrial tachyarrhythmias (AT) in patients with tetralogy of Fallot (ToF) are associated with congestive heart failure, stroke, and cardiac death. Effective treatment is therefore essential. The aim of the study is to evaluate long-term outcome of ablative therapy of AT in ToF patients and to study characteristics of AT recurrences.