Confocal microscopy applied to the study of single entity fluorescence and light scattering

A sample scanning confocal optical microscope (SCOM) was designed and constructed in order to perform local measurements of fluorescence, light scattering and Raman scattering. This instrument allows to measure time resolved fluorescence, Raman scattering and light scattering from the same diffraction limited spot. Fluorescence from single molecules and light scattering from metallic nanoparticles can be studied. First, the electric field distribution in the focus of the SCOM was modelled. This enables the design of illumination modes for different purposes, such as the determination of the three-dimensional orientation of single chromophores. Second, a method for the calculation of the de-excitation rates of a chromophore was presented. This permits to compare different detection schemes and experimental geometries in order to optimize the collection of fluorescence photons. Both methods were combined to calculate the SCOM fluorescence signal of a chromophore in a general layered system. The fluorescence excitation and emission of single molecules through a thin gold film was investigated experimentally and modelled. It was demonstrated that, due to the mediation of surface plasmons, single molecule fluorescence near a thin gold film can be excited and detected with an epi-illumination scheme through the film. Single molecule fluorescence as close as 15nm to the gold film was studied in this manner. The fluorescence dynamics (fluorescence blinking and excited state lifetime) of single molecules was studied in the presence and in the absence of a nearby gold film in order to investigate the influence of the metal on the electronic transition rates. The trace-histogram and the autocorrelation methods for the analysis of single molecule fluorescence blinking were presented and compared via the analysis of Monte-Carlo simulated data. The nearby gold influences the total decay rate in agreement to theory. The gold presence produced no influence on the ISC rate from the excited state to the triplet but increased by a factor of 2 the transition rate from the triplet to the singlet ground state. The photoluminescence blinking of Zn0.42Cd0.58Se QDs on glass and ITO substrates was investigated experimentally as a function of the excitation power (P) and modelled via Monte-Carlo simulations. At low P, it was observed that the probability of a certain on- or off-time follows a negative power-law with exponent near to 1.6. As P increased, the on-time fraction reduced on both substrates whereas the off-times did not change. A weak residual memory effect between consecutive on-times and consecutive off-times was observed but not between an on-time and the adjacent off-time. All of this suggests the presence of two independent mechanisms governing the lifetimes of the on- and off-states. The simulated data showed Poisson-distributed off- and on-intensities, demonstrating that the observed non-Poissonian on-intensity distribution of the QDs is not a product of the underlying power-law probability and that the blinking of QDs occurs between a non-emitting off-state and a distribution of emitting on-states with different intensities. All the experimentally observed photo-induced effects could be accounted for by introducing a characteristic lifetime tPI of the on-state in the simulations. The QDs on glass presented a tPI proportional to P-1 suggesting the presence of a one-photon process. Light scattering images and spectra of colloidal and C-shaped gold nano-particles were acquired. The minimum size of a metallic scatterer detectable with the SCOM lies around 20 nm.

Investigations on maar-diatreme volcanoes by inversion of magnetic and gravity data from the Eifel area, Germany

A study of maar-diatreme volcanoes has been perfomed by inversion of gravity and magnetic data. The geophysical inverse problem has been solved by means of the damped nonlinear least-squares method. To ensure stability and convergence of the solution of the inverse problem, a mathematical tool, consisting in data weighting and model scaling, has been worked out. Theoretical gravity and magnetic modeling of maar-diatreme volcanoes has been conducted in order to get information, which is used for a simple rough qualitative and/or quantitative interpretation. The information also serves as a priori information to design models for the inversion and/or to assist the interpretation of inversion results. The results of theoretical modeling have been used to roughly estimate the heights and the dip angles of the walls of eight Eifel maar-diatremes — each taken as a whole. Inversemodeling has been conducted for the Schönfeld Maar (magnetics) and the Hausten-Morswiesen Maar (gravity and magnetics). The geometrical parameters of these maars, as well as the density and magnetic properties of the rocks filling them, have been estimated. For a reliable interpretation of the inversion results, beside the knowledge from theoretical modeling, it was resorted to other tools such like field transformations and spectral analysis for complementary information. Geologic models, based on thesynthesis of the respective interpretation results, are presented for the two maars mentioned above. The results gave more insight into the genesis, physics and posteruptive development of the maar-diatreme volcanoes. A classification of the maar-diatreme volcanoes into three main types has been elaborated. Relatively high magnetic anomalies are indicative of scoria cones embeded within maar-diatremes if they are not caused by a strong remanent component of the magnetization. Smaller (weaker) secondary gravity and magnetic anomalies on the background of the main anomaly of a maar-diatreme — especially in the boundary areas — are indicative for subsidence processes, which probably occurred in the late sedimentation phase of the posteruptive development. Contrary to postulates referring to kimberlite pipes, there exists no generalized systematics between diameter and height nor between geophysical anomaly and the dimensions of the maar-diatreme volcanoes. Although both maar-diatreme volcanoes and kimberlite pipes are products of phreatomagmatism, they probably formed in different thermodynamic and hydrogeological environments. In the case of kimberlite pipes, large amounts of magma and groundwater, certainly supplied by deep and large reservoirs, interacted under high pressure and temperature conditions. This led to a long period phreatomagmatic process and hence to the formation of large structures. Concerning the maar-diatreme and tuff-ring-diatreme volcanoes, the phreatomagmatic process takes place due to an interaction between magma from small and shallow magma chambers (probably segregated magmas) and small amounts of near-surface groundwater under low pressure and temperature conditions. This leads to shorter time eruptions and consequently to structures of smaller size in comparison with kimberlite pipes. Nevertheless, the results show that the diameter to height ratio for 50% of the studied maar-diatremes is around 1, whereby the dip angle of the diatreme walls is similar to that of the kimberlite pipes and lies between 70 and 85°. Note that these numerical characteristics, especially the dip angle, hold for the maars the diatremes of which — estimated by modeling — have the shape of a truncated cone. This indicates that the diatreme can not be completely resolved by inversion.

Flash floods and their effects on the development in El-Qaá plain area in South Sinai, Egypt

The arid regions are dominated to a much larger degree than humid regions by major catastrophic events. Although most of Egypt lies within the great hot desert belt; it experiences especially in the north some torrential rainfall, which causes flash floods all over Sinai Peninsula. Flash floods in hot deserts are characterized by high velocity and low duration with a sharp discharge peak. Large sediment loads may be carried by floods threatening fields and settlements in the wadis and even people who are living there. The extreme spottiness of rare heavy rainfall, well known to desert people everywhere, precludes any efficient forecasting. Thus, although the limitation of data still reflects pre-satellite methods, chances of developing a warning system for floods in the desert seem remote. The relatively short flood-to-peak interval, a characteristic of desert floods, presents an additional impediment to the efficient use of warning systems. The present thesis contains introduction and five chapters, chapter one points out the physical settings of the study area. There are the geological settings such as outcrop lithology of the study area and the deposits. The alluvial deposits of Wadi Moreikh had been analyzed using OSL dating to know deposits and palaeoclimatic conditions. The chapter points out as well the stratigraphy and the structure geology containing main faults and folds. In addition, it manifests the pesent climate conditions such as temperature, humidity, wind and evaporation. Besides, it presents type of soils and natural vegetation cover of the study area using unsupervised classification for ETM+ images. Chapter two points out the morphometric analysis of the main basins and their drainage network in the study area. It is divided into three parts: The first part manifests the morphometric analysis of the drainage networks which had been extracted from two main sources, topographic maps and DEM images. Basins and drainage networks are considered as major influencing factors on the flash floods; Most of elements were studied which affect the network such as stream order, bifurcation ratio, stream lengths, stream frequency, drainage density, and drainage patterns. The second part of this chapter shows the morphometric analysis of basins such as area, dimensions, shape and surface. Whereas, the third part points the morphometric analysis of alluvial fans which form most of El-Qaá plain. Chapter three manifests the surface runoff through rainfall and losses analysis. The main subject in this chapter is rainfall which has been studied in detail; it is the main reason for runoff. Therefore, all rainfall characteristics are regarded here such as rainfall types, distribution, rainfall intensity, duration, frequency, and the relationship between rainfall and runoff. While the second part of this chapter concerns with water losses estimation by evaporation and infiltration which are together the main losses with direct effect on the high of runoff. Finally, chapter three points out the factors influencing desert runoff and runoff generation mechanism. Chapter four is concerned with assessment of flood hazard, it is important to estimate runoff and tocreate a map of affected areas. Therefore, the chapter consists of four main parts; first part manifests the runoff estimation, the different methods to estimate runoff and its variables such as runoff coefficient lag time, time of concentration, runoff volume, and frequency analysis of flash flood. While the second part points out the extreme event analysis. The third part shows the map of affected areas for every basin and the flash floods degrees. In this point, it has been depending on the DEM to extract the drainage networks and to determine the main streams which are normally more dangerous than others. Finally, part four presets the risk zone map of total study area which is of high inerest for planning activities. Chapter five as the last chapter concerns with flash flood Hazard mitigation. It consists of three main parts. First flood prediction and the method which can be used to predict and forecast the flood. The second part aims to determine the best methods which can be helpful to mitigate flood hazard in the arid zone and especially the study area. Whereas, the third part points out the development perspective for the study area indicating the suitable places in El-Qaá plain for using in economic activities.

Petrogenetic evolution of Uralian-Alaskan-type mafic-ultramafic complexes in the southern and middle Urals, Russia

The PhD thesis at hand consists of three parts and describes the petrogenetic evolution of Uralian-Alaskan-type mafic ultramafic complexes in the Ural Mountains, Russia. Uralian-Alaskan-type mafic-ultramafic complexes are recognized as a distinct class of intrusions. Characteristic petrologic features are the concentric zonation of a central dunite body grading outward into wehrlite, clinopyroxenite and gabbro, the absence of orthopyroxene and frequently occurring platinum group element (PGE) mineralization. In addition, the presence of ferric iron-rich spinel discriminates Uralian-Alaskan-type complexes from most other mafic ultramafic rock assemblages. The studied Uralian-Alaskan-type complexes (Nizhnii Tagil, Kytlym and Svetley Bor) belong to the southern part of a 900 km long, N–S-trending chain of similar intrusions between the Main Uralian Fault to the west and the Serov-Mauk Fault to the east. The first chapter of this thesis studies the evolution of the ultramafic rocks tracing the compositional variations of rock forming and accessory minerals. The comparison of the chemical composition of olivine, clinopyroxene and chromian spinel from the Urals with data from other localities indicates that they are unique intrusions having a characteristic spinel and clinopyroxene chemistry. Laser ablation-ICPMS (LA-ICPMS ) analyses of trace element concentrations in clinopyroxene are used to calculate the composition of their parental melt which is characterized by enriched LREE (0.5-5.2 prim. mantle) and other highly incompatible elements (U, Th, Ba, Rb) relative to the HREE (0.25-2.0 prim. mantle). A subduction-related geotectonic setting is indicated by a positive anomaly for Sr and negative anomalies for Ti, Zr and Hf. The mineral compositions monitor the evolution of the parental magmas and decipher differences between the studied complexes. In addition, the observed variation in LREE/HREE (for example La/Lu = 2-24) can be best explained with the model of an episodically replenished and erupted open magma chamber system with the extensive fractionation of olivine, spinel and clinopyroxene. The data also show that ankaramites in a subduction-related geotectonic setting could represent parental magmas of Uralian-Alaskan-type complexes. The second chapter of the thesis discusses the chemical variation of major and trace elements in rock-forming minerals of the mafic rocks. Electron microprobe and LA-ICPMS analyses are used to quantitatively describe the petrogenetic relationship between the different gabbroic lithologies and their genetic link to the ultramafic rocks. The composition of clinopyroxene identifies the presence of melts with different trace element abundances on the scale of a thin section and suggests the presence of open system crustal magma chambers. Even on a regional scale the large variation of trace element concentrations and ratios in clinopyroxene (e.g. La/Lu = 3-55) is best explained by the interaction of at least two fundamentally different magma types at various stages of fractionation. This requires the existence of a complex magma chamber system fed with multiple pulses of magmas from at least two different coeval sources in a subduction-related environment. One source produces silica saturated Island arc tholeiitic melts. The second source produces silica undersaturated, ultra-calcic, alkaline melts. Taken these data collectively, the mixing of the two different parental magmas is the dominant petrogenetic process explaining the observed chemical variations. The results further imply that this is an intrinsic feature of Uralian-Alaskan-type complexes and probably of many similar mafic-ultramafic complexes world-wide. In the third chapter of this thesis the major element composition of homogeneous and exsolved spinel is used as a petrogenetic indicator. Homogeneous chromian spinel in dunites and wehrlites monitors the fractionation during the early stages of the magma chamber and the onset of clinopyroxene fractionation as well as the reaction of spinel with interstitial liquid. Exsolved spinel is present in mafic and ultramafic rocks from all three studied complexes. Its composition lies along a solvus curve which defines an equilibrium temperature of 600°C, given that spinel coexists with olivine. This temperature is considered to be close to the temperature of the host rocks into which the studied Uralian-Alaskan-type complexes intruded. The similarity of the exsolution temperatures in the different complexes over a distance of several hundred kilometres implies a regional tectonic event that terminated the exsolution process. This event is potentially associated with the final exhumation of the Uralian-Alaskan-type complexes along the Main Uralian Fault and the Serov-Mauk Fault in the Uralian fold belt.

Implications of regional fault distribution and kinematics for the uplift of rift flanks around the Rwenzori Mountains, Southwestern Uganda

Das Ziel dieser Arbeit bestand in der Untersuchung der Störungsverteilung und der Störungskinematik im Zusammenhang mit der Hebung der Riftschultern des Rwenzori Gebirges.rnDas Rwenzori Gebirge befindet sich im NNE-SSWbis N-S verlaufenden Albertine Rift, des nördlichsten Segments des westlichen Armes des Ostafrikanischen Grabensystems. Das Albertine Rift besteht aus Becken unterschiedlicher Höhe, die den Lake Albert, Lake Edward, Lake George und Lake Kivu enthalten. Der Rwenzori horst trennt die Becken des Lake Albert und des Lake Edward. Es erstreckt sich 120km in N-S Richtung, sowie 40-50km in E-W Richtung, der h¨ochste Punkt befindet sich 5111 ü. NN. Diese Studie untersucht einen Abschnitt des Rifts zwischen etwa 1°N und 0°30'S Breite sowie 29°30' und 30°30' östlicher Länge ersteckt. Auch die Feldarbeit konzentrierte sich auf dieses Gebiet.rnrnHauptzweck dieser Studie bestand darin, die folgende These auf ihre Richtigkeit zu überprüfen: ’Wenn es im Verlauf der Zeit tatsächlich zu wesentlichen Änderungen in der Störungskinematik kam, dann ist die starke Hebung der Riftflanken im Bereich der Rwenzoris nicht einfach durch Bewegung entlang der Graben-Hauptst¨orungen zu erklären. Vielmehr ist sie ein Resultat des Zusammenspiels mehrerer tektonische Prozesse, die das Spannungsfeld beeinflussen und dadurch Änderungen in der Kinematik hervorrufen.’ Dadurch konzentrierte sich die Studie in erster Linie auf die Störungsanalyse.rnrnDie Kenntnis regionaler Änderungen der Extensionsrichtung ist entscheidend für das Verständnis komplexer Riftsysteme wie dem Ostafrikanischen Graben. Daher bestand der Kern der Untersuchung in der Kartierung von Störungen und der Untersuchung der Störungskinematik. Die Aufnahme strukturgeologischer Daten konzentrierte sich auf die Ugandische Seite des Rifts, und Pal¨aospannungen wurden mit Hilfe von St¨orungsdaten durch Spannungsinversion rekonstruiert.rnDie unterschiedliche Orientierung spr¨oder Strukturen im Gelände, die geometrische Analyse der geologischen Strukturen sowie die Ergebnisse von Mikrostrukturen im Dünnschliff (Kapitel 4) weisen auf verschiedene Spannungsfelder hin, die auf mögliche Änderungen der Extensionsrichtung hinweisen. Die Resultate der Spannungsinversion sprechen für Ab-, Über- und Blattverschiebungen sowie für Schrägüberschiebungen (Kapitel 5). Aus der Orientierung der Abschiebungen gehen zwei verschiedene Extensionsrichtungen hervor: im Wesentlichen NW-SE Extension in fast allen Gebieten, sowie NNE-SSW Extension im östlichen Zentralbereich.rnAus der Analyse von Blattverschiebungen ergaben sich drei unterschiedliche Spannungszustände. Zum Einen NNW-SSE bis N-S Kompression in Verbindung mit ENE-WSW bzw E-W Extension wurde für die nördlichen und die zentralen Ruwenzoris ausgemacht. Ein zweiter Spannungszustand mit WNW-ESE Kompression/NNE-SSW Extension betraf die Zentralen Rwenzoris. Ein dritter Spannungszustand mit NNW-SSE Extension betraf den östlichen Zentralteil der Rwenzoris. Schrägüberschiebungen sind durch dazu schräge Achsen charakterisiert, die für N-S bis NNW-SSE Kompression sprechen und ausschließlich im östlichen Zentralabschnitt auftreten. Überschiebungen, die hauptsächlich in den zentralen und den östlichen Rwenzoris auftreten, sprechen für NE-SW orientierten σ2-Achsen und NW-SE Extension.rnrnEs konnten drei unterschiedliche Spannungseinflüsse identifiziert werden: auf die kollisionsbedingte Bildung eines Überschiebungssystem folgte intra-kratonische Kompression und schließlich extensionskontrollierte Riftbildung. Der Übergang zwischen den beiden letztgenannten Spannungszuständen erfolgte Schrittweise und erzeugte vermutlich lokal begrenzte Transpression und Transtension. Gegenw¨artig wird die Störungskinematik der Region durch ein tensiles Spannungsregime in NW-SE bis N-S Richtung bestimmt.rnrnLokale Spannungsvariationen werden dabei hauptsächlich durch die Interferenzrndes regionalen Spannungsfeldes mit lokalen Hauptst¨orungen verursacht. Weitere Faktoren die zu lokalen Veränderungen des Spannungsfeldes führen können sind unterschiedliche Hebungsgeschwindigkeiten, Blockrotation oder die Interaktion von Riftsegmenten. Um den Einfluß präexistenter Strukturen und anderer Bedingungen auf die Hebung der Rwenzoris zu ermitteln, wurde der Riftprozeß mit Hilfe eines analogen ’Sandbox’-Modells rekonstruiert (Kapitel 6). Da sich die Moho-Diskontinuität im Bereich des Arbeitsgebietes in einer Tiefe von 25 km befindet, aktive Störungen aber nur bis zu einer Tiefe von etwa 20 km beobachtet werden können (Koehn et al. 2008), wurden nur die oberen 25 km im Modell nachbebildet. Untersucht und mit Geländebeobachtungen verglichen wurden sowohl die Reihenfolge, in der Riftsegmente entstehen, als auch die Muster, die sich im Verlauf der Nukleierung und des Wachstums dieser Riftsegmente ausbilden. Das Hauptaugenmerk wurde auf die Entwicklung der beiden Subsegmente gelegt auf denen sich der Lake Albert bzw. der Lake Edward und der Lake George befinden, sowie auf das dazwischenliegende Rwenzori Gebirge. Das Ziel der Untersuchung bestand darin herauszufinden, in welcher Weise das südwärts propagierende Lake Albert-Subsegment mit dem sinistral versetzten nordwärts propagierenden Lake Edward/Lake George-Subsegment interagiert.rnrnVon besonderem Interesse war es, in welcherWeise die Strukturen innerhalb und außerhalb der Rwenzoris durch die Interaktion dieser Riftsegmente beeinflußt wurden. rnrnDrei verschiedene Versuchsreihen mit unterschiedlichen Randbedingungen wurden miteinander verglichen. Abhängig vom vorherrschenden Deformationstyp der Transferzone wurden die Reihen als ’Scherungs-dominiert’, ’Extensions-dominiert’ und als ’Rotations-dominiert’ charakterisiert. Die Beobachtung der 3-dimensionalen strukturellen Entwicklung der Riftsegmente wurde durch die Kombination von Modell-Aufsichten mit Profilschnitten ermöglicht. Von den drei genannten Versuchsreihen entwickelte die ’Rotationsdominierten’ Reihe einen rautenförmiger Block im Tranferbereich der beiden Riftsegmente, der sich um 5−20° im Uhrzeigersinn drehte. DieserWinkel liegt im Bereich des vermuteten Rotationswinkel des Rwenzori-Blocks (5°). Zusammengefasst untersuchen die Sandbox-Versuche den Einfluss präexistenter Strukturen und der Überlappung bzw. Überschneidung zweier interagierender Riftsegmente auf die Entwicklung des Riftsystems. Sie befassen sich darüber hinaus mit der Frage, welchen Einfluss Blockbildung und -rotation auf das lokale Stressfeld haben.

Expanding the scope of poly(ethylene glycol)s for bioconjugation to squaric acid-mediated PEGylation and pH-sensitivity

Poly(ethylene glycol) (PEG) is used in a broad range of applications due to its unique combination of properties and is approved use in formulations for body-care products, edibles and medicine. This thesis aims at the synthesis and characterization of novel heterofunctional PEG structures and the establishment of diethyl squarate as a suitable linker for the covalent attachment to proteins. Chapter 1 is an introduction on the properties and applications of PEG as well as the fascinating chemistry of squaric acid derivatives. In Chapter 1.1, the synthesis and properties of PEG are described, and the versatile applications of PEG derivatives in everyday products are emphasized with a focus on PEG-based pharmaceuticals and nonionic surfactants. This chapter is written in German, as it was published in the German Journal Chemie in unserer Zeit. Chapter 1.2 deals with PEGs major drawbacks, its non-biodegradability, which impedes parenteral administration of PEG conjugates with polyethers exceeding the renal excretion limit, although these would improve blood circulation times and passive tumor targeting. This section gives a comprehensive overview of the cleavable groups that have been implemented in the polyether backbone to tackle this issue as well as the synthetic strategies employed to accomplish this task. Chapter 1.3 briefly summarizes the chemical properties of alkyl squarates and the advantages in protein conjugation chemistry that can be taken from its use as a coupling agent. In Chapter 2, the application of diethyl squarate as a coupling agent in the PEGylation of proteins is illustrated. Chapter 2.1 describes the straightforward synthesis and characterization of squaric acid ethyl ester amido PEGs with terminal hydroxyl functions or methoxy groups. The reactivity and selectivity of theses activated PEGs are explored in kinetic studies on the reactions with different lysine and other amino acid derivatives, followed by 1H NMR spectroscopy. Further, the efficient attachment of the novel PEGs to a model protein, i.e., bovine serum albumin (BSA), demonstrates the usefulness of the new linker for the PEGylation with heterofunctional PEGs. In Chapter 2.3 initial studies on the biocompatibility of polyether/BSA conjugates synthesized by the squaric acid mediated PEGylation are presented. No cytotoxic effects on human umbilical vein endothelial cells exposed to various concentrations of the conjugates were observed in a WST-1 assay. A cell adhesion molecule - enzyme immunosorbent assay did not reveal the expression of E-selectin or ICAM-1, cell adhesion molecules involved in inflammation processes. The focus of Chapter 3 lies on the syntheses of novel heterofunctional PEG structures which are suitable candidates for the squaric acid mediated PEGylation and exhibit superior features compared to established PEGs applied in bioconjugation. Chapter 3.1 describes the synthetic route to well-defined, linear heterobifunctional PEGs carrying a single acid-sensitive moiety either at the initiation site or at a tunable position in the polyether backbone. A universal concept for the implementation of acetal moieties into initiators for the anionic ring-opening polymerization (AROP) of epoxides is presented and proven to grant access to the degradable PEG structures aimed at. The hydrolysis of the heterofunctional PEG with the acetal moiety at the initiating site is followed by 1H NMR spectroscopy in deuterium oxide at different pH. In an exploratory study, the same polymer is attached to BSA via the squarate acid coupling and subsequently cleaved from the conjugate under acidic conditions. Furthermore, the concept for the generation of acetal-modified AROP initiators is demonstrated to be suitable for cholesterol, and the respective amphiphilic cholesteryl-PEG is cleaved at lowered pH. In Chapter 3.2, the straightforward synthesis of α-amino ω2-dihydroxyl star-shaped three-arm PEGs is described. To assure a symmetric length of the hydroxyl-terminated PEG arms, a novel AROP initiator is presented, who’s primary and secondary hydroxyl groups are separated by an acetal moiety. Upon polymerization of ethylene oxide for these functionalities and subsequent cleavage of the acid-labile unit no difference in the degree of polymerization is seen for both polyether fragments.