Development and application of a GC system for NMHC analyses of air samples from the CARIBIC aircraft project

The subject of this thesis is the development of a Gaschromatography (GC) system for non-methane hydrocarbons (NMHCs) and measurement of samples within the project CARIBIC (Civil Aircraft for the Regular Investigation of the atmosphere Based on an Instrument Container, www.caribic-atmospheric.com). Air samples collected at cruising altitude from the upper troposphere and lowermost stratosphere contain hydrocarbons at low levels (ppt range), which imposes substantial demands on detection limits. Full automation enabled to maintain constant conditions during the sample processing and analyses. Additionally, automation allows overnight operation thus saving time. A gas chromatography using flame ionization detection (FID) together with the dual column approach enables simultaneous detection with almost equal carbon atom response for all hydrocarbons except for ethyne. The first part of this thesis presents the technical descriptions of individual parts of the analytical system. Apart from the sample treatment and calibration procedures, the sample collector is described. The second part deals with analytical performance of the GC system by discussing tests that had been made. Finally, results for measurement flight are assessed in terms of quality of the data and two flights are discussed in detail. Analytical performance is characterized using detection limits for each compound, using uncertainties for each compound, using tests of calibration mixture conditioning and carbon dioxide trap to find out their influence on analyses, and finally by comparing the responses of calibrated substances during period when analyses of the flights were made. Comparison of both systems shows good agreement. However, because of insufficient capacity of the CO2 trap the signal of one column was suppressed due to breakthroughed carbon dioxide so much that its results appeared to be unreliable. Plausibility tests for the internal consistency of the given data sets are based on common patterns exhibited by tropospheric NMHCs. All tests show that samples from the first flights do not comply with the expected pattern. Additionally, detected alkene artefacts suggest potential problems with storing or contamination within all measurement flights. Two last flights # 130-133 and # 166-169 comply with the tests therefore their detailed analysis is made. Samples were analyzed in terms of their origin (troposphere vs. stratosphere, backward trajectories), their aging (NMHCs ratios) and detected plumes were compared to chemical signatures of Asian outflows. In the last chapter a future development of the presented system with focus on separation is drawn. An extensive appendix documents all important aspects of the dissertation from theoretical introduction through illustration of sample treatment to overview diagrams for the measured flights.

Finite-element discretization of 3D energy-transport equations for semiconductors

In this thesis a mathematical model was derived that describes the charge and energy transport in semiconductor devices like transistors. Moreover, numerical simulations of these physical processes are performed. In order to accomplish this, methods of theoretical physics, functional analysis, numerical mathematics and computer programming are applied. After an introduction to the status quo of semiconductor device simulation methods and a brief review of historical facts up to now, the attention is shifted to the construction of a model, which serves as the basis of the subsequent derivations in the thesis. Thereby the starting point is an important equation of the theory of dilute gases. From this equation the model equations are derived and specified by means of a series expansion method. This is done in a multi-stage derivation process, which is mainly taken from a scientific paper and which does not constitute the focus of this thesis. In the following phase we specify the mathematical setting and make precise the model assumptions. Thereby we make use of methods of functional analysis. Since the equations we deal with are coupled, we are concerned with a nonstandard problem. In contrary, the theory of scalar elliptic equations is established meanwhile. Subsequently, we are preoccupied with the numerical discretization of the equations. A special finite-element method is used for the discretization. This special approach has to be done in order to make the numerical results appropriate for practical application. By a series of transformations from the discrete model we derive a system of algebraic equations that are eligible for numerical evaluation. Using self-made computer programs we solve the equations to get approximate solutions. These programs are based on new and specialized iteration procedures that are developed and thoroughly tested within the frame of this research work. Due to their importance and their novel status, they are explained and demonstrated in detail. We compare these new iterations with a standard method that is complemented by a feature to fit in the current context. A further innovation is the computation of solutions in three-dimensional domains, which are still rare. Special attention is paid to applicability of the 3D simulation tools. The programs are designed to have justifiable working complexity. The simulation results of some models of contemporary semiconductor devices are shown and detailed comments on the results are given. Eventually, we make a prospect on future development and enhancements of the models and of the algorithms that we used.

Functional hydrogels

Hydrogels are used in a variety of applications in daily life, such as super absorbers, contact lenses and in drug delivery. Functional hydrogels that allow the incorporation of additional functionalities have enormous potential for future development. The properties of such hydrogels can be diversified by introducing responsiveness to external stimuli. These crosslinked polymers are known to respond to changes in temperature, pH and pressure, as well as chemical and electrical stimuli, magnetic fields and irradiation. From this responsive behavior possible applications arise in many fields like drug delivery, tissue engineering, purification and implementation as actuators, biosensors or for medical coatings. However, their interaction with biomaterial and way of functioning are yet not fully understood. Therefore, thorough investigations regarding their optical, mechanical and chemical nature have to be conducted. A UV-crosslinkable polymer, consisting of N-isopropylacrylamide, methacrylic acid and the UV-crosslinker 4-benzoylphenyl methacrylate was synthesized. Its composition, determined by a comprehensive NMR study, is equivalent to the composition of the monomer mixture. The chemical characteristics were preserved during the subsequently formation of hydrogel films by photo-crosslinking as proved by XPS. For the optical characterization, e.g. the degree of swelling of very thin films, the spectroscopy of coupled long range surface plasmons is introduced. Thicker films, able to guide light waves were analyzed with combined surface plasmon and optical waveguide mode spectroscopy (SPR/OWS). The evaluation of the data was facilitated by the reverse Wentzel-Kramers-Brillouin (WKB) approximation. The meshsize and proper motion of the surface anchored hydrogels were investigated by fluorescence correlation spectroscopy (FCS), micro photon correlation spectroscopy (µPCS) and SPR/OWS. The studied gels exhibit a meshsize that allowed for the diffusion of small biomolecules inside their network. For future enhancement of probing diffusants, a dye that enables FRET in FCS was immobilized in the gel and the diffusion of gold-nanoparticles embedded in the polymer solution was studied by PCS. These properties can be conveniently tuned by the crosslinking density, which depends on the irradiation dose. Additionally, protocols and components for polymer analogous reactions based on active ester chemistry of the hydrogel were developed. Based on these syntheses and investigations, the hydrogel films are applied in the fields of medical coatings as well as in biosensing as matrix and biomimetic cushion. Their non-adhesive properties were proved in cell experiments, SPR/OWS and ToF-SIMS studies. The functionality and non-fouling property of the prepared hydrogels allowed for adaption to the needs of the respective application.

Global simulated soil biogenic nitric oxide (NO) emissions: Impact, improvement and innovation

rnNitric oxide (NO) is important for several chemical processes in the atmosphere. Together with nitrogen dioxide (NO2 ) it is better known as nitrogen oxide (NOx ). NOx is crucial for the production and destruction of ozone. In several reactions it catalyzes the oxidation of methane and volatile organic compounds (VOCs) and in this context it is involved in the cycling of the hydroxyl radical (OH). OH is a reactive radical, capable of oxidizing most organic species. Therefore, OH is also called the “detergent” of the atmosphere. Nitric oxide originates from several sources: fossil fuel combustion, biomass burning, lightning and soils. Fossil fuel combustion is the largest source. The others are, depending on the reviewed literature, generally comparable to each other. The individual sources show a different temporal and spatial pattern in their magnitude of emission. Fossil fuel combustion is important in densely populated places, where NO from other sources is less important. In contrast NO emissions from soils (hereafter SNOx) or biomass burning are the dominant source of NOx in remote regions.rnBy applying an atmospheric chemistry global climate model (AC-GCM) I demonstrate that SNOx is responsible for a significant part of NOx in the atmosphere. Furthermore, it increases the O3 and OH mixing ratio substantially, leading to a ∼10% increase in the oxidizing efficiency of the atmosphere. Interestingly, through reduced O3 and OH mixing ratios in simulations without SNOx, the lifetime of NOx increases in regions with other dominating sources of NOx

From carbazole-containing and pi-expanded triangular trinuclear porphyrinoids

Zusammenfassung:rnDie vorliegende Arbeit beschreibt das Design und die Synthese neuartiger Porphyrinoide anhand der Modifikation und der π-Systemausdehnung an der Peripherie des Porphyrin-Gerüsts. Die Darstellung künstlicher Porphyrine ist von Interesse, da neue physiko-chemischen Eigenschaften erhalten und untersucht werden können. Die in dieser Arbeit vorgestellten Porphyrinoide wurden mit Hilfe von modernen Synthesemethoden wie den metallkatalysierten Kreuzkupplungen und somit durch Aryl-Aryl Verknüpfungen aufgebaut.rnDer erste Teil dieser Arbeit befasst sich mit der Modifikation des Porphyrin-Gerüsts. Porphyrine bestehen aus jeweils zwei Pyrrol- und Pyrrolenin-Einheiten, welche systematisch ausgetauscht wurden. Die Pyrrol-Einheiten wurden durch Carbazol ersetzt, das sich formal vom Pyrrol durch Anfügen von zwei Benzogruppen ableitet und deshalb besonders gut geeignet ist. Die Pyrrolenin-Einheiten wurden aus folgenden Gründen durch andere Heterozyklen wie Pyridin, Pyrrol oder Triazol ersetzt: rn* Nachbildung des stabilen Porphyrin trans-NH-Tautomers (Carbazol und Pyridin)rn* Nachbildung von (NH)4-Liganden wie Calix[4]pyrrol (Carbazol und Pyrrol)rn* Vereinigung von N-H und C-H Wasserstoffbrücken-Donor-Einheiten in einem Makrozyklus (Carbazol und Triazol)rnDie Synthese eines drei-Zentren Porphyrinoids mit ausgedehntem π-System wird im zweiten Teil der vorliegenden Arbeit beschrieben. Dieses Thema basiert auf der aktuellen Entwicklung von nicht-Edelmetall basierten Katalysatoren für die Reduktion von Sauerstoff. Hier werden derzeit N4 makrozyklische Metallkomplexe, die mehrere katalytisch aktive Stellen aufweisen, untersucht. In diesem Zusammenhang, hat die Gruppe von Prof. Müllen einen neuartigen drei-Zentren-Komplex entwickelt. Ausgehend von diesen Erkenntnissen, dient diese Arbeit zur Verbesserung der katalytischen Aktivität des drei-Zentren-Komplex durch die Variation von verschieden Substituenten. Hierbei wurden zwei wesentliche Konzepte verfolgt:rn* Vernetzung durch die Bildung von Netzwerken oder durch Pyrolyse in der Mesophasern* Verbesserung des Katalysator-Trägermaterial-KontaktsrnNeben den Synthesen wurden die Eigenschaften und möglichen Anwendungen dieser neuartigen Materialen untersucht, wie z.B. als Liganden für Übergangsmetalle, als Anionenrezeptoren oder als Elektrokatalysatoren für die Reduktion von Sauerstoff. rn

Die Rolle der humanen Enzyme Paraoxonase-2 und -3 bei Krebserkrankungen und Pseudomonas-Infektionen

Die vorliegende Arbeit befasste sich mit der Charakterisierung molekularer Funktionen humaner Paraoxonase (PON) Enzyme, insbesondere die der Proteine PON2 und PON3 im Hinblick auf medizinisch-relevante Fragestellungen. Zum einen wurde die Rolle von PON3 in der Tumorgenese und zum anderen eine mögliche Schutzfunktion von PON2 und PON3 gegenüber P. aeruginosa Infektionen untersucht. Bereits seit dem Jahr 2000 ist die anti-oxidative Eigenschaft von PON3 bekannt, jedoch war der zugrundeliegende Mechanismus bisher ungeklärt. Im Rahmen dieser Arbeit wurde gezeigt, dass PON3 die Superoxid-Entstehung in den Mitochondrien abschwächt, wobei sie ihre anti-oxidative Eigenschaft vermutlich durch eine direkte Coenzym Q10-Interaktion in der inneren mitochondrialen Membran vermittelt. Dies führt zu weniger oxidativen Stress, zur Abschwächung mitochondrial-induzierter apoptotischer Signalwege und zur erhöhten Resistenz gegenüber Chemotherapeutika. Gleichzeitig wurde demonstriert, dass sich Tumorzellen diese anti-oxidative Eigenschaft zu Nutze machen. PON3 war in zahlreichen Tumorgeweben überexprimiert. Es konnte eine mögliche Funktion von PON3 als Tumormarker und Angriffspunkt in der Krebstherapie aufgezeigt werden. Die hier erlangten Daten liefern wertvolle Hinweise auf die Rolle von PON3 in Krebserkrankungen, welche eine Basis für zukünftige Analysen darstellen, die der Entwicklung neuer Krebstherapien dienen könnten. Ein weiterer Teil der Arbeit befasste sich mit der gegenseitigen Beeinflussung der Enzyme PON2 / PON3 und der für P.aeruginosa essentiellen Virulenzfaktoren Pyocyanin (PCN) und dem Lacton 3OC12. Erstmalig wurde gezeigt, dass PON3 zellschädigende PCN-Effekte abschwächen kann, nämlich die PCN-induzierte Superoxid-Produktion, NF-kB-Aktivierung und IL-8-Sekretion. PON2 schützt in gleicher Weise gegen PCN und hydrolysiert zugleich noch das Lacton 3OC12. Folglich sind PON2 und PON3 wichtige Bestandteile der angeborenen Immunität, werden jedoch durch eine 3OC12-induzierte Ca2+-Mobilisation inaktiviert. Weitere Analysen ergaben, dass die PON2-Inaktivierung wahrscheinlich über einen Ca2+ / Calcineurin / Calmodulin-abhängigen Signalweg erfolgt, welcher eine offenbar regulative Serin311-Dephosphorylierung in PON2 vermittelt. Ähnliches könnte für PON3 gelten und wird derzeit erforscht, da eine Stabilisierung der enzymatischen Aktivitäten von PON2 und PON3 der bakteriellen Virulenz entscheidend entgegen wirken könnte.

Brand formative design - development and assessment of product design from a future, brand and consumer perspective

With this dissertation research we investigate intersections between design and marketing and in this respect, which factors do contribute that a product design becomes brand formative. We have developed a Brand Formative Design (BFD) framework, which investigates individual design features in a holistic, comparable, brand relevant, and consumer specific context. We discuss what kinds of characteristics contribute to BFD but also illuminate how they should be applied and examine: rnA holistic framework leading to Brand Formative Design. Identification and assessment of BFD Drivers. The dissection of products into three Distinctive Design Levels. The detection of surprising design preferences. The appropriate degree of scheme deviation with evolutionary design. Simulated BFD development processes with three different products and the integration of consumers. Future oriented objectification, comparability and assessment of design. Recommendations for the management of design in a brand specific context. Design is a product feature, which contributes significantly to the success of products. However, the development of new design contains challenges. Design can hardly be objectified; many people have an opinion concerning the attractiveness of new products but cannot formulate their future preferences. Product design is widely developed based on intuition, which can be difficult for the management of design. Here the concept of Brand Formative Design can provide a framework which contributes to structure, objectify, develop and assess new evolutionary design in brand and future relevant contexts, but also integrates consumers and their preferences without restricting creativity too much.