Sphärische Bürsten in polymeren Schmelzen

Colloidal nanoparticles are additives to improve or modify several properties of thermoplastic or elastic polymers. Usually colloid-polymer mixtures show phase separation due to the depletion effect. The strategy to overcome this depletion demixing was to prepare surface-modified colloidal particles, which can be blended with linear polymer chains homogeneous. A successful synthesis strategy for the preparation of hairy nanospheres was developed by grafting polystyrene macromonomer chains onto polyorganosiloxane microgels. The number of hairs per particle with a core radius of approximately 10nm exceeded 150 hairs in all cases. The molecular weight of the hairs variied between 4000-18000g/mol.The compatibility of these hairy spheres mixed with linear polymer chains was investigated by AFM, TEM and SAXS. Homogeneous mixtures were found if the molecular weight of the polymer hairs on the particle surface is at least as large as the molecular weight of the matrix chains. If the chains are much shorter than the hairs, the colloidal hair corona is strongly swollen by the matrix polymer, leading to a long-range soft interparticle repulsion ('wet brush'). If hairs and chains are comparable in length, the corona shows much less volume swelling, leading to a short-range repulsive potential similar to hard sphere systems ('dry brush'). Polymerketten und Kolloidpartikel entmischen aufgrund von Depletion-Wechselwirkungen. Diese entropisch bedingte Entmischung konnte durch das Ankoppeln von Polymerhaaren verschiedenen Molekulargewichts auf die Kugeloberflächen der Kolloide bis zu hohen Konzentrationen vermieden werden. Zur Darstellung sphärischer Bürsten und haariger Tracerpartikel wurde eine neue Synthesestrategie ausgearbeitet und erfolgreich umgesetzt.Das Kompatibilitätsverhalten dieser sphärischen Bürsten in der Schmelze von Polymerketten als Matrix wurde mittels Elektronenmikroskopie und Kleinwinkelröntgenstreuung untersucht. Die Mischungen setzten sich aus sphärischen Bürsten und Matrixketten mit unterschiedlichen Molekulargewichten zusammen.Es zeigte sich, daß die Mischbarkeit entschieden durch das Verhältnis von Haarlänge zu Länge der Matrixketten beeinflußt wird.Aus den Untersuchungen des Relaxationsverhaltens mittels Rheologie und SAXS ergibt sich, daß das Konzept der 'dry brush'- und 'wet brush'-Systeme auf diese Mischungen übertragbar ist. Die Volumenquellung der Haarcorona durch die Matrixketten ist, wie die Experimente gezeigt haben, bereits im Fall von Polymeren mit relativ niedrigen Molekulargewichten zu beobachten. Sie ist umso stärker ausgeprägt, je größer das Längenverhältnis zwischen Polymerhaaren und Matrixketten ist. Die Quellung bedeutet eine Vergrößerung des effektiven Radius der Partikel und entspricht somit einer Erhöhung des effektiven Volumenbruchs. Dies führt zur Ausbildung einer höheren Ordnung und zu einem Einfrieren der Relaxation dieser strukturellen Ordnung führt.

Polymakromonomere als anisotropes Modellsystem zur Untersuchung kolloidaler Mehrkomponentensysteme

Das Ziel dieser Arbeit bestand in der Untersuchung des Phasenverhaltens kolloidaler Mehrkomponentensysteme. Konzentrierte und kompatible Mischungen aus linearen Polymerketten und Polymakromonomeren als kolloidanaloge Partikel wurden auf ihre Eignung hin ein kolloidales Glas zu bilden untersucht.Die Synthese der Polymakromonomere erfolgte durch radikalische Polymerisation von Vinylbenzyl-Makromer, was zu zylinderartigen Makromolekülen führt, die auch als molekulare „Flaschenbürsten“ angesehen werden können. Aufgrund der grossen Längen-Polydispersität der Hauptkette wurden die erhaltenen Polymakromonomere mittels Continous Polymer Fractionation (CPF) fraktioniert, was zu Modell-Partikeln von verschiedener Molekülgestalt führte: von kugelförmig über stäbchenförmig bis hin zu wurmartig.Weiterhin konnte gezeigt werden, dass die „haarige“ Oberfläche der Polymakromonomere zumindestens teilweise die entropisch bedingte Entmischung von Partikeln unterschiedlicher Molekülgestalt, wie Polymerknäuel und stäbchenartige, überwinden kann.Um das dynamische Verhalten zu untersuchen, wurden rheologische Messungen an den Schmelzen verschiedener Kolloid-Polymer-Mischungen ausgeführt. Es zeigte sich, dass Polymakromonomere mit grosser Hauptkettenlänge bzw. wurmartiger Gestalt einen signifikanten Verstärkungseffekt auf die Kolloid-Polymer-Mischung haben.

Charakterisierung der Vinorin-Synthase aus Rauvolfia serpentina durch Reinigung, Expression, Mutation und Kristallisation

ABSTRACTDie vorliegende Arbeit befasste sich mit der Reinigung,heterologen Expression, Charakterisierung, molekularenAnalyse, Mutation und Kristallisation des EnzymsVinorin-Synthase. Das Enzym spielt eine wichtige Rolle inder Ajmalin-Biosynthese, da es in einerAcetyl-CoA-abhängigen Reaktion die Umwandlung desSarpagan-Alkaloids 16-epi-Vellosimin zu Vinorin unterBildung des Ajmalan-Grundgerüstes katalysiert. Nach der Reinigung der Vinorin-Synthase ausHybrid-Zellkulturen von Rauvolfia serpentina/Rhazya strictamit den fünf chromatographischen TrennmethodenAnionenaustauschchromatographie an SOURCE 30Q, HydrophobeInteraktionen Chromatographie an SOURCE 15PHE,Chromatographie an MacroPrep Ceramic Hydroxyapatit,Anionenaustauschchromatographie an Mono Q undGrößenausschlußchromatographie an Superdex 75 konnte dieVinorin-Synthase aus 2 kg Zellkulturgewebe 991fachangereichert werden.Das nach der Reinigung angefertigte SDS-Gel ermöglichte eineklare Zuordnung der Protein-Bande als Vinorin-Synthase.Der Verdau der Enzymbande mit der Endoproteinase LysC unddie darauffolgende Sequenzierung der Spaltpeptide führte zuvier Peptidsequenzen. Der Datenbankvergleich (SwissProt)zeigte keinerlei Homologien zu Sequenzen bekannterPflanzenenzyme. Mit degenerierten Primern, abgeleitet voneinem der erhaltenen Peptidfragmente und einer konserviertenRegion bekannter Acetyltransferasen gelang es, ein erstescDNA-Fragment der Vinorin-Synthase zu amplifizieren. Mit derMethode der RACE-PCR wurde die Nukleoidsequenzvervollständigt, was zu einem cDNA-Vollängenklon mit einerGröße von 1263 bp führte, der für ein Protein mit 421Aminosäuren (46 kDa) codiert.Das Vinorin-Synthase-Gen wurde in den pQE2-Expressionsvektorligiert, der für einen N-terminalen 6-fachen His-tagcodiert. Anschließend wurde sie erstmals erfolgreich in E.coli im mg-Maßstab exprimiert und bis zur Homogenitätgereinigt. Durch die erfolgreiche Überexpression konnte dieVinorin-Synthase eingehend charakterisiert werden. DerKM-Wert für das Substrat Gardneral wurde mit 20 µM, bzw.41.2 µM bestimmt und Vmax betrug 1 pkat, bzw. 1.71 pkat.Nach erfolgreicher Abspaltung des His-tags wurden diekinetischen Parameter erneut bestimmt (KM- Wert 7.5 µM, bzw.27.52 µM, Vmax 0.7 pkat, bzw. 1.21 pkat). Das Co-Substratzeigt einen KM- Wert von 60.5 µM (Vmax 0.6 pkat). DieVinorin-Synthase besitzt ein Temperatur-Optimum von 35 °Cund ein pH-Optimum bei 7.8.Homologievergleiche mit anderen Enzymen zeigten, dass dieVinorin-Synthase zu einer noch kleinen Familie von bisher 10Acetyltransferasen gehört. Alle Enzyme der Familie haben einHxxxD und ein DFGWG-Motiv zu 100 % konserviert. Basierendauf diesen Homologievergleichen und Inhibitorstudien wurden11 in dieser Proteinfamilie konservierte Aminosäuren gegenAlanin ausgetauscht, um so die Aminosäuren einer in derLiteratur postulierten katalytischen Triade(Ser/Cys-His-Asp) zu identifizieren.Die Mutation aller vorhandenen konservierten Serine undCysteine resultierte in keiner Mutante, die zumvollständigen Aktivitätsverlust des Enzyms führte. Nur dieMutationen H160A und D164A resultierten in einemvollständigen Aktivitätsverlust des Enzyms. Dieses Ergebniswiderlegt die Theorie einer katalytischen Triade und zeigte,dass die Aminosäuren H160A und D164A exklusiv an derkatalytischen Reaktion beteiligt sind.Zur Überprüfung dieser Ergebnisse und zur vollständigenAufklärung des Reaktionsmechanismus wurde dieVinorin-Synthase kristallisiert. Die bis jetzt erhaltenenKristalle (Kristallgröße in µm x: 150, y: 200, z: 200)gehören der Raumgruppe P212121 (orthorhombisch primitiv) anund beugen bis 3.3 Å. Da es bis jetzt keine Kristallstruktureines zur Vinorin-Synthase homologen Proteins gibt, konntedie Struktur noch nicht vollständig aufgeklärt werden. ZurLösung des Phasenproblems wird mit der Methode der multiplenanomalen Dispersion (MAD) jetzt versucht, die ersteKristallstruktur in dieser Enzymfamilie aufzuklären.

Complexes of polyelectrolytes with defined charge distance and different dendrimer counterions

Complexes of polyelectrolytes with defined charge distance and different dendrimer counterions Magdalena Chelmecka Max Planck Institute for Polymer Research; Ackermannweg 10; D-55128 Mainz ; Tel.: (+49) 06131- 379 – 226 A study of complexes in solution is of interest to investigate whether the formation of well-defined assemblies like in classical surfactant systems is possible. Aim of this thesis is to investigate the electrostatic self-assembly of linear polycations of varying charge distance with “large” counterions of varying architecture. We especially investigate the morphology of objects formed, but also their stability under salt free condition and after low molecular mass salt addition. As polycations, Poly(dialkylimino)-alkylene salts (Ionenes) I65MeBr and I25MeBr were chosen. Ionenes are synthesized via Menschutkin reaction and characterized by standard methods. Counterions are Polyamidoamine (PAMAM) dendrimers of generations G2.5, G5.5, G7.5 with -COONa surface groups and shape-persistent, Polyphenylene dendrimers of generation G1 with surface -COOH groups. A complex interplay of interactions is expected to direct the self assembly via electrostatic interaction, geometric factors, hydrophobic interaction or hydrogen bonds. Methods used for the investigation of complexes are: UV-spectroscopy, pH-metric techniques, dynamic and static light scattering, small angle neutron scattering,  potential measurements and potentiometric titration. Under certain conditions, (i.e. charge ratio of compounds, charge density of ionene and dendrimer also concentration of sample) polyelectrolyte systems composed of ionenes and dendrimers build complexes in solution. System compounds are typical polyelectrolytes, but structures which they build behave not usual for typical polyelectrolytes. In a one diffusion mode regime aggregates of about 100 nm hydrodynamic radius have been found. Such aggregates are core-shell or anisotropic core shell structures in the case of ionenes/PAMAM dendrimers complexes. These complexes are stable even at high ionic strength. In case of ionenes with poly(phenylene) dendrimers, hard sphere-like objects or spherical objects with hairy-like surface have been found in a one diffusion mode regime. Their stability at high ionic strength is lower. For the ionenes/poly(phenylene) dendrimers systems one transition point has been found from one to two diffusion processes, towards increasing ionene concentration, i.e. for the samples with fixed dendrimer concentration towards increasing ionic strength. For the diffusion profile of ionene/PAMAM dendrimers in most cases two transition regimes are observed. One at very low ionene concentration, the second one at high ionene concentrations, which again means for the samples with fixed dendrimer concentration, also at higher ionic strength. Both two mode regimes are separated by the one mode regime. As was confirmed experimentally, the one diffusion mode regime is caused by the motion of well defined assemblies. The two diffusion mode regimes are caused by the movement of different sized species in solution, large aggregates and middle-size aggregates (oligoaggregates). The location and also the number of transition points in the diffusion profiles is dependent on the ionene to dendrimer charge ratio, charge density of the compounds and concentration. No influence of the molecular mass of the ionene has been found. The aggregates are found to be charged on the surface, however this surface charge does not significantly influence the diffusion properties of the system.

Structuring of polymer surface by evaporation of sessile microdrops

In this thesis, we investigated the evaporation of sessile microdroplets on different solid substrates. Three major aspects were studied: the influence of surface hydrophilicity and heterogeneity on the evaporation dynamics for an insoluble solid substrate, the influence of external process parameters and intrinsic material properties on microstructuring of soluble polymer substrates and the influence of an increased area to volume ratio in a microfluidic capillary, when evaporation is hindered. In the first part, the evaporation dynamics of pure sessile water drops on smooth self-assembled monolayers (SAMs) of thiols or disulfides on gold on mica was studied. With increasing surface hydrophilicity the drop stayed pinned longer. Thus, the total evaporation time of a given initial drop volume was shorter, since the drop surface, through which the evaporation occurs, stays longer large. Usually, for a single drop the volume decreased linearly with t1.5, t being the evaporation time, for a diffusion-controlled evaporation process. However, when we measured the total evaporation time, ttot, for multiple droplets with different initial volumes, V0, we found a scaling of the form V0 = attotb. The more hydrophilic the substrate was, the more showed the scaling exponent a tendency to an increased value up to 1.6. This can be attributed to an increasing evaporation rate through a thin water layer in the vicinity of the drop. Under the assumption of a constant temperature at the substrate surface a cooling of the droplet and thus a decreased evaporation rate could be excluded as a reason for the different scaling exponent by simulations performed by F. Schönfeld at the IMM, Mainz. In contrast, for a hairy surface, made of dialkyldisulfide SAMs with different chain lengths and a 1:1 mixture of hydrophilic and hydrophobic end groups (hydroxy versus methyl group), the scaling exponent was found to be ~ 1.4. It increased to ~ 1.5 with increasing hydrophilicity. A reason for this observation can only be speculated: in the case of longer hydrophobic alkyl chains the formation of an air layer between substrate and surface might be favorable. Thus, the heat transport to the substrate might be reduced, leading to a stronger cooling and thus decreased evaporation rate. In the second part, the microstructuring of polystyrene surfaces by drops of toluene, a good solvent, was investigated. For this a novel deposition technique was developed, with which the drop can be deposited with a syringe. The polymer substrate is lying on a motorized table, which picks up the pendant drop by an upward motion until a liquid bridge is formed. A consecutive downward motion of the table after a variable delay, i.e. the contact time between drop and polymer, leads to the deposition of the droplet, which can evaporate. The resulting microstructure is investigated in dependence of the processes parameters, i.e. the approach and the retraction speed of the substrate and the delay between them, and in dependence of the intrinsic material properties, i.e. the molar mass and the type of the polymer/solvent system. The principal equivalence with the microstructuring by the ink-jet technique was demonstrated. For a high approach and retraction speed of 9 mm/s and no delay between them, a concave microtopology was observed. In agreement with the literature, this can be explained by a flow of solvent and the dissolved polymer to the rim of the pinned droplet, where polymer is accumulated. This effect is analogue to the well-known formation of ring-like stains after the evaporation of coffee drops (coffee-stain effect). With decreasing retraction speed down to 10 µm/s the resulting surface topology changes from concave to convex. This can be explained with the increasing dissolution of polymer into the solvent drop prior to the evaporation. If the polymer concentration is high enough, gelation occurs instead of a flow to the rim and the shape of the convex droplet is received. With increasing delay time from below 0 ms to 1s the depth of the concave microwells decreases from 4.6 µm to 3.2 µm. However, a convex surface topology could not be obtained, since for longer delay times the polymer sticks to the tip of the syringe. Thus, by changing the delay time a fine-tuning of the concave structure is accomplished, while by changing the retraction speed a principal change of the microtopolgy can be achieved. We attribute this to an additional flow inside the liquid bridge, which enhanced polymer dissolution. Even if the pendant drop is evaporating about 30 µm above the polymer surface without any contact (non-contact mode), concave structures were observed. Rim heights as high as 33 µm could be generated for exposure times of 20 min. The concave structure exclusively lay above the flat polymer surface outside the structure even after drying. This shows that toluene is taken up permanently. The increasing rim height, rh, with increasing exposure time to the solvent vapor obeys a diffusion law of rh = rh0  tn, with n in the range of 0.46 ~ 0.65. This hints at a non-Fickian swelling process. A detailed analysis showed that the rim height of the concave structure is modulated, unlike for the drop deposition. This is due to the local stress relaxation, which was initiated by the increasing toluene concentration in the extruded polymer surface. By altering the intrinsic material parameters i.e. the polymer molar mass and the polymer/solvent combination, several types of microstructures could be formed. With increasing molar mass from 20.9 kDa to 1.44 MDa the resulting microstructure changed from convex, to a structure with a dimple in the center, to concave, to finally an irregular structure. This observation can be explained if one assumes that the microstructuring is dominated by two opposing effects, a decreasing solubility with increasing polymer molar mass, but an increasing surface tension gradient leading to instabilities of Marangoni-type. Thus, a polymer with a low molar mass close or below the entanglement limit is subject to a high dissolution rate, which leads to fast gelation compared to the evaporation rate. This way a coffee-rim like effect is eliminated early and a convex structure results. For high molar masses the low dissolution rate and the low polymer diffusion might lead to increased surface tension gradients and a typical local pile-up of polymer is found. For intermediate polymer masses around 200 kDa, the dissolution and evaporation rate are comparable and the typical concave microtopology is found. This interpretation was supported by a quantitative estimation of the diffusion coefficient and the evaporation rate. For a different polymer/solvent system, polyethylmethacrylate (PEMA)/ethylacetate (EA), exclusively concave structures were found. Following the statements above this can be interpreted with a lower dissolution rate. At low molar masses the concentration of PEMA in EA most likely never reaches the gelation point. Thus, a concave instead of a convex structure occurs. At the end of this section, the optically properties of such microstructures for a potential application as microlenses are studied with laser scanning confocal microscopy. In the third part, the droplet was confined into a glass microcapillary to avoid evaporation. Since here, due to an increased area to volume ratio, the surface properties of the liquid and the solid walls became important, the influence of the surface hydrophilicity of the wall on the interfacial tension between two immiscible liquid slugs was investigated. For this a novel method for measuring the interfacial tension between the two liquids within the capillary was developed. This technique was demonstrated by measuring the interfacial tensions between slugs of pure water and standard solvents. For toluene, n-hexane and chloroform 36.2, 50.9 and 34.2 mN/m were measured at 20°C, which is in a good agreement with data from the literature. For a slug of hexane in contact with a slug of pure water containing ethanol in a concentration range between 0 and 70 (v/v %), a difference of up to 6 mN/m was found, when compared to commercial ring tensiometry. This discrepancy is still under debate.

Sequence-controlled synthesis of soluble oligo(p-benzamide)s

This work focused on the synthesis of novel monomers for the design of a series of oligo(p-benzamide)s following two approaches: iterative solution synthesis and automated solid phase protocols. These approaches present a useful method to the sequence-controlled synthesis of side-chain and main-chain functionalized oligomers for the preparation of an immense variety of nanoscaffolds. The challenge in the synthesis of such materials was their modification, while maintaining the characteristic properties (physical-chemical properties, shape persistence and anisotropy). The strategy for the preparation of predictable superstructures was devote to the selective control of noncovalent interactions, monodispersity and monomer sequence. In addition to this, the structure-properties correlation of the prepared rod-like soluble materials was pointed. The first approach involved the solution-based aramide synthesis via introduction of 2,4-dimethoxybenzyl N-amide protective group via an iterative synthetic strategy The second approach focused on the implementation of the salicylic acid scaffold to introduce substituents on the aromatic backbone for the stabilization of the OPBA-rotamers. The prepared oligomers were analyzed regarding their solubility and aggregation properties by systematically changing the degree of rotational freedom of the amide bonds, side chain polarity, monomer sequence and degree of oligomerization. The syntheses were performed on a modified commercial peptide synthesizer using a combination of fluorenylmethoxycarbonyl (Fmoc) and aramide chemistry. The automated synthesis allowed the preparation of aramides with potential applications as nanoscaffolds in supramolecular chemistry, e.g. comb-like-