The development of stylolites, from small-scale heterogeneities to multi-scale roughness

Stylolites are rough paired surfaces, indicative of localized stress-induced dissolution under a non-hydrostatic state of stress, separated by a clay parting which is believed to be the residuum of the dissolved rock. These structures are the most frequent deformation pattern in monomineralic rocks and thus provide important information about low temperature deformation and mass transfer. The intriguing roughness of stylolites can be used to assess amount of volume loss and paleo-stress directions, and to infer the destabilizing processes during pressure solution. But there is little agreement on how stylolites form and why these localized pressure solution patterns develop their characteristic roughness.rnNatural bedding parallel and vertical stylolites were studied in this work to obtain a quantitative description of the stylolite roughness and understand the governing processes during their formation. Adapting scaling approaches based on fractal principles it is demonstrated that stylolites show two self affine scaling regimes with roughness exponents of 1.1 and 0.5 for small and large length scales separated by a crossover length at the millimeter scale. Analysis of stylolites from various depths proved that this crossover length is a function of the stress field during formation, as analytically predicted. For bedding parallel stylolites the crossover length is a function of the normal stress on the interface, but vertical stylolites show a clear in-plane anisotropy of the crossover length owing to the fact that the in-plane stresses (σ2 and σ3) are dissimilar. Therefore stylolite roughness contains a signature of the stress field during formation.rnTo address the origin of stylolite roughness a combined microstructural (SEM/EBSD) and numerical approach is employed. Microstructural investigations of natural stylolites in limestones reveal that heterogeneities initially present in the host rock (clay particles, quartz grains) are responsible for the formation of the distinctive stylolite roughness. A two-dimensional numerical model, i.e. a discrete linear elastic lattice spring model, is used to investigate the roughness evolving from an initially flat fluid filled interface induced by heterogeneities in the matrix. This model generates rough interfaces with the same scaling properties as natural stylolites. Furthermore two coinciding crossover phenomena in space and in time exist that separate length and timescales for which the roughening is either balanced by surface or elastic energies. The roughness and growth exponents are independent of the size, amount and the dissolution rate of the heterogeneities. This allows to conclude that the location of asperities is determined by a polimict multi-scale quenched noise, while the roughening process is governed by inherent processes i.e. the transition from a surface to an elastic energy dominated regime.rn

Forward modelling of petrological crust-forming processes on the early Earth

Tonalite-trondhjemite-granodiorite (TTG) gneisses form up to two-thirds of the preserved Archean continental crust and there is considerable debate regarding the primary magmatic processes of the generation of these rocks. The popular theories indicate that these rocks were formed by partial melting of basaltic oceanic crust which was previously metamorphosed to garnet-amphibolite and/or eclogite facies conditions either at the base of thick oceanic crust or by subduction processes.rnThis study investigates a new aspect regarding the source rock for Archean continental crust which is inferred to have had a bulk compostion richer in magnesium (picrite) than present-day basaltic oceanic crust. This difference is supposed to originate from a higher geothermal gradient in the early Archean which may have induced higher degrees of partial melting in the mantle, which resulted in a thicker and more magnesian oceanic crust. rnThe methods used to investigate the role of a more MgO-rich source rock in the formation of TTG-like melts in the context of this new approach are mineral equilibria calculations with the software THERMOCALC and high-pressure experiments conducted from 10–20 kbar and 900–1100 °C, both combined in a forward modelling approach. Initially, P–T pseudosections for natural rock compositions with increasing MgO contents were calculated in the system NCFMASHTO (Na2O–CaO–FeO–MgO–Al2O3–SiO2–H2O–TiO2) to ascertain the metamorphic products from rocks with increasing MgO contents from a MORB up to a komatiite. A small number of previous experiments on komatiites showed the development of pyroxenite instead of eclogite and garnet-amphibolite during metamorphism and established that melts of these pyroxenites are of basaltic composition, thus again building oceanic crust instead of continental crust.rnThe P–T pseudosections calculated represent a continuous development of their metamorphic products from amphibolites and eclogites towards pyroxenites. On the basis of these calculations and the changes within the range of compositions, three picritic Models of Archean Oceanic Crust (MAOC) were established with different MgO contents (11, 13 and 15 wt%) ranging between basalt and komatiite. The thermodynamic modelling for MAOC 11, 13 and 15 at supersolidus conditions is imprecise since no appropriate melt model for metabasic rocks is currently available and the melt model for metapelitic rocks resulted in unsatisfactory calculations. The partially molten region is therfore covered by high-pressure experiments. The results of the experiments show a transition from predominantly tonalitic melts in MAOC 11 to basaltic melts in MAOC 15 and a solidus moving towards higher temperatures with increasing magnesium in the bulk composition. Tonalitic melts were generated in MAOC 11 and 13 at pressures up to 12.5 kbar in the presence of garnet, clinopyroxene, plagioclase plus/minus quartz (plus/minus orthopyroxene in the presence of quartz and at lower pressures) in the absence of amphibole but it could not be explicitly indicated whether the tonalitic melts coexisting with an eclogitic residue and rutile at 20 kbar do belong to the Archean TTG suite. Basaltic melts were generated predominantly in the presence of granulite facies residues such as amphibole plus/minus garnet, plagioclase, orthopyroxene that lack quartz in all MAOC compositions at pressures up to 15 kbar. rnThe tonalitic melts generated in MAOC 11 and 13 indicate that thicker oceanic crust with more magnesium than that of a modern basalt is also a viable source for the generation of TTG-like melts and therefore continental crust in the Archean. The experimental results are related to different geologic settings as a function of pressure. The favoured setting for the generation of early TTG-like melts at 15 kbar is the base of an oceanic crust thicker than existing today or by melting of slabs in shallow subduction zones, both without interaction of tonalic melts with the mantle. Tonalitic melts at 20 kbar may have been generated below the plagioclase stability by slab melting in deeper subduction zones that have developed with time during the progressive cooling of the Earth, but it is unlikely that those melts reached lower pressure levels without further mantle interaction.rn