Petrographie und Geochemie des Eckfelder Maares und von Hillscheid und die Einbindung in den Hocheifelvulkanismus

Tertiäre Vulkanite aus dem Eckfelder Maar, dem Hillscheider Diatrem und dem Hillscheid Basalt (Schlot) wurden petrologisch und geochemisch untersucht. Bis auf tonige Klasten aus dem Bohrkern des Eckfelder Maares handelt es sich bei allen weiteren Proben um undifferenzierte basische Vulkanite. Die tonigen Klasten aus dem Bohrkern müssen der ehemaligen Landoberfläche vor der Eruption des Eckfelder Maares zugerechnet werden, in dessen Krater sie während der Eruption hineingefallen sind. Bis auf die Proben des Hillscheid Basaltes sind die Proben alteriert. Die Alteration zeigt sich an der Bildung von Zeolithen und Calcitmineralisationen, die primär und sekundär gebildete Hohlräume aufgefüllt haben oder an einer vertonten Grundmasse der Proben, die daneben Mineraleinschlüsse (Spinell) und kantige Fremdgesteinsbruchstücke enthalten können. Bei den Proben mit vertonter Grundmasse handelt es sich um Palagonite, Umwandlungsprodukte aus Sideromelan (basaltischem Glas). Geochemische Analysen an Grundmassepräparaten der alterierten bis vertonten Proben zeigen, dass außer den immobilen Elementen Ti, Nb, Zr, Y alle weiteren Elemente teilweise bis vollständig abgereichert worden sind. Eine Ausnahme bildet Barium (Ba), welches z.T. in beträchtlichen Mengen in Zeolithen (Harmotom) angereichert wurde. Bei den Proben aus dem Eckfelder Maar kann die Alteration bis Vertonung der Proben alleine mit der Palagonitisierung und Verwitterung erklärt werden. Es gibt keine Hinweise auf Materialzufuhr und damit für sich anschließende hydrothermale Prozesse. Die Proben des Hillscheider Diatrem sind wesentlich geringer alteriert (glasige Grundmasse). Neuste Erkenntnisse aus einer Bohrung im Sommer 1999 im vermuteten Zentrum des Hillscheider Diatrems beschränken das Diatrem maximal auf einen kleineren Bereich im Nordosten der bisherigen Lokation. Bei der Bohrung stieß man nach 20 Meter auf Anstehendes. Im Hangschutt darüber fand man Blöcke des Hillscheid Basaltes. Eine geringere Größe der Lokation zusammen mit der geringen Alteration könnten auf deren Entstehung mit einer initialen Maarphase gefolgt von Schlackentätigkeit hinweisen. Die Schlacken könnten die ersten Ablagerungen vor Verwitterung geschützt haben. Allerdings gibt es keine Funde die eine Schlackentätigkeit belegen. Beim sogenannten 'Hillscheider Diatrem' könnte es sich aber auch um Hangschutt aus der Randbreccie des Hillscheider Basaltes handeln. Zusammen mit Bruchstücken aus dem Schlot des Hillscheid Basaltes wären die Palagonite des sogenannten 'Hillscheider Diatrem' erst in jüngster Zeit im Bereich einer Uferböschung zur Ablagerung gekommen. Dies würde allerdings das sogenannte 'Hillscheider Diatrem' in seiner Existenz in Frage stellen. Vergleiche der Proben des Hillscheid Basaltes mit basischen Hocheifelvulkaniten deuten auf kogenetische Beziehung aller Proben untereinander und ordnen die Proben des Hillscheid Basaltes geochemisch dem Hocheifelvulkanismus zu. REE- und weitere Spurenelementgehalte und auch deren Elementverhältnisse weisen für alle tertiären Eifelvulkanite gemeinsam auf Mantelschmelzen aus dem Bereich eines Granatperidotits mit niedrigen Aufschmelzgraden um ein Prozent hin. Vergleich der Elementverhältnisse hochinkompatibler Elemente im Bezug auf die Bildung mafischer Schmelzen mit primitivem Mantel deuten darauf hin, dass der Mantel im Bereich der Hocheifel verarmt ist an K, Rb, Sr und angereichert an Ba und eventuell an Nb. Ursachen für diese von typisch primären Mantelzusammensetzung abweichenden Verhältnisse könnten durch Mischungen von Mantelschmelzen mit lithosphärischem Mantel (K-Anomalie) und durch Anreicherungen mit fluiden Phasen (Ba-Anomalie) oder auch Schmelzen aus einem tieferliegenden Plume (Kelberger Hoch) verursacht worden sein. Englischer Zusammenfassung:

Tetraurea derivatives of calix[4]arenes and oligocalix[4]arenes, synthesis and self-assembly = Tetraharnstoff-Derivate von Calix[4 ]arenen und Oligocalix[4]arenen, Synthese und Selbstorganisierung

Wide rim tetraurea calix[4]arenes form hydrogen bonded dimeric capsules in apolar solvents in the presence of a suitable guest, which must be included in the cavity. The monomeric and dimeric form are never observed simultaneously under usual conditions. In general the combination of two different alkyl or aryl tetraurea derivatives results in the mixture of two homodimers and a heterodimer, however, only the heterodimeric species is observed in the 1:1 mixture of aryl and tosyl ureas. The (hetero)dimerization of oligourea calix[4]arenes (units) was used to construct larger structures via self-assembly of multiple calixarenes (building blocks) containing two (or more) covalently connected units. Among these self-assembled structures linear or branched polymers, cyclic oligomers and well-organized dendrimers were envisaged. The synthesis of the building blocks requires the preparation of calix[4]arene units possessing one (or more) functional group at the narrow or wide rim. Finally the oligourea units were covalently connected either directly or via suitable spacers within appropriate building blocks using amide bonds. Self-assembly properties of such building blocks were investigated.

Self-assembled structures based on functionalized calix[4]arenes and calix[8]arenes = Selbstorganisierte Strukturen basierend auf funktionalisierten Calix[4]- und Calix[8]arenen

Calix[4]arenes with urea functions attached to the p-positions of the phenolic units usually form dimers in apolar solvents. Tetraureas functionalized by pyridyl and carboxyl groups form dimers only with bis- or tetraloop tetraureas. This heterodimerization was used for the synthesis of a bis-[3]catenane. Tetraureas functionalized with sulfide functions were synthesized for the preparation of monolayers from the dimeric capsules containing electrochemically active guests on gold. Bis-tetraureacalix[4]arenes singly-linked via their wide rim by rigid spacers were synthesized and their self-assembly to polymers in apolar solvents was proved by the 1H NMR spectroscopy and AFM studies. Dimerization of the first example of the tetraurea calix[4]arenes bridged in 1,3-positions at the narrow rim was proved by 1H NMR spectroscopy. Calix[8]arenes functionalized by urea, amido or naphthalimido groups at their p-positions self-assemble to columnar structures by hydrogen bonding or by π-π-stacking.

Calix[4]arenes in the 1,3-alternate conformation

Calix[4]arenes fixed in the 1,3-alternate conformation offer an interesting platform for the attachment of further functionalities which has been less frequently used than the cone conformer. Several synthetic strategies were developed to attach four amino functions to the narrow rim, to the wide rim and to both rims of the calix[4]arene fixed in the 1,3-alternate conformation. Using different precursor groups (nitrile/phthalimide or nitro/phthalimide) which can be independently converted into amino functions opens the possibility to attach further groups selectively to the amino functions. Here the groups which is newly attached will determine the reaction sequence.

Structuring of polymer surface by evaporation of sessile microdrops

In this thesis, we investigated the evaporation of sessile microdroplets on different solid substrates. Three major aspects were studied: the influence of surface hydrophilicity and heterogeneity on the evaporation dynamics for an insoluble solid substrate, the influence of external process parameters and intrinsic material properties on microstructuring of soluble polymer substrates and the influence of an increased area to volume ratio in a microfluidic capillary, when evaporation is hindered. In the first part, the evaporation dynamics of pure sessile water drops on smooth self-assembled monolayers (SAMs) of thiols or disulfides on gold on mica was studied. With increasing surface hydrophilicity the drop stayed pinned longer. Thus, the total evaporation time of a given initial drop volume was shorter, since the drop surface, through which the evaporation occurs, stays longer large. Usually, for a single drop the volume decreased linearly with t1.5, t being the evaporation time, for a diffusion-controlled evaporation process. However, when we measured the total evaporation time, ttot, for multiple droplets with different initial volumes, V0, we found a scaling of the form V0 = attotb. The more hydrophilic the substrate was, the more showed the scaling exponent a tendency to an increased value up to 1.6. This can be attributed to an increasing evaporation rate through a thin water layer in the vicinity of the drop. Under the assumption of a constant temperature at the substrate surface a cooling of the droplet and thus a decreased evaporation rate could be excluded as a reason for the different scaling exponent by simulations performed by F. Schönfeld at the IMM, Mainz. In contrast, for a hairy surface, made of dialkyldisulfide SAMs with different chain lengths and a 1:1 mixture of hydrophilic and hydrophobic end groups (hydroxy versus methyl group), the scaling exponent was found to be ~ 1.4. It increased to ~ 1.5 with increasing hydrophilicity. A reason for this observation can only be speculated: in the case of longer hydrophobic alkyl chains the formation of an air layer between substrate and surface might be favorable. Thus, the heat transport to the substrate might be reduced, leading to a stronger cooling and thus decreased evaporation rate. In the second part, the microstructuring of polystyrene surfaces by drops of toluene, a good solvent, was investigated. For this a novel deposition technique was developed, with which the drop can be deposited with a syringe. The polymer substrate is lying on a motorized table, which picks up the pendant drop by an upward motion until a liquid bridge is formed. A consecutive downward motion of the table after a variable delay, i.e. the contact time between drop and polymer, leads to the deposition of the droplet, which can evaporate. The resulting microstructure is investigated in dependence of the processes parameters, i.e. the approach and the retraction speed of the substrate and the delay between them, and in dependence of the intrinsic material properties, i.e. the molar mass and the type of the polymer/solvent system. The principal equivalence with the microstructuring by the ink-jet technique was demonstrated. For a high approach and retraction speed of 9 mm/s and no delay between them, a concave microtopology was observed. In agreement with the literature, this can be explained by a flow of solvent and the dissolved polymer to the rim of the pinned droplet, where polymer is accumulated. This effect is analogue to the well-known formation of ring-like stains after the evaporation of coffee drops (coffee-stain effect). With decreasing retraction speed down to 10 µm/s the resulting surface topology changes from concave to convex. This can be explained with the increasing dissolution of polymer into the solvent drop prior to the evaporation. If the polymer concentration is high enough, gelation occurs instead of a flow to the rim and the shape of the convex droplet is received. With increasing delay time from below 0 ms to 1s the depth of the concave microwells decreases from 4.6 µm to 3.2 µm. However, a convex surface topology could not be obtained, since for longer delay times the polymer sticks to the tip of the syringe. Thus, by changing the delay time a fine-tuning of the concave structure is accomplished, while by changing the retraction speed a principal change of the microtopolgy can be achieved. We attribute this to an additional flow inside the liquid bridge, which enhanced polymer dissolution. Even if the pendant drop is evaporating about 30 µm above the polymer surface without any contact (non-contact mode), concave structures were observed. Rim heights as high as 33 µm could be generated for exposure times of 20 min. The concave structure exclusively lay above the flat polymer surface outside the structure even after drying. This shows that toluene is taken up permanently. The increasing rim height, rh, with increasing exposure time to the solvent vapor obeys a diffusion law of rh = rh0  tn, with n in the range of 0.46 ~ 0.65. This hints at a non-Fickian swelling process. A detailed analysis showed that the rim height of the concave structure is modulated, unlike for the drop deposition. This is due to the local stress relaxation, which was initiated by the increasing toluene concentration in the extruded polymer surface. By altering the intrinsic material parameters i.e. the polymer molar mass and the polymer/solvent combination, several types of microstructures could be formed. With increasing molar mass from 20.9 kDa to 1.44 MDa the resulting microstructure changed from convex, to a structure with a dimple in the center, to concave, to finally an irregular structure. This observation can be explained if one assumes that the microstructuring is dominated by two opposing effects, a decreasing solubility with increasing polymer molar mass, but an increasing surface tension gradient leading to instabilities of Marangoni-type. Thus, a polymer with a low molar mass close or below the entanglement limit is subject to a high dissolution rate, which leads to fast gelation compared to the evaporation rate. This way a coffee-rim like effect is eliminated early and a convex structure results. For high molar masses the low dissolution rate and the low polymer diffusion might lead to increased surface tension gradients and a typical local pile-up of polymer is found. For intermediate polymer masses around 200 kDa, the dissolution and evaporation rate are comparable and the typical concave microtopology is found. This interpretation was supported by a quantitative estimation of the diffusion coefficient and the evaporation rate. For a different polymer/solvent system, polyethylmethacrylate (PEMA)/ethylacetate (EA), exclusively concave structures were found. Following the statements above this can be interpreted with a lower dissolution rate. At low molar masses the concentration of PEMA in EA most likely never reaches the gelation point. Thus, a concave instead of a convex structure occurs. At the end of this section, the optically properties of such microstructures for a potential application as microlenses are studied with laser scanning confocal microscopy. In the third part, the droplet was confined into a glass microcapillary to avoid evaporation. Since here, due to an increased area to volume ratio, the surface properties of the liquid and the solid walls became important, the influence of the surface hydrophilicity of the wall on the interfacial tension between two immiscible liquid slugs was investigated. For this a novel method for measuring the interfacial tension between the two liquids within the capillary was developed. This technique was demonstrated by measuring the interfacial tensions between slugs of pure water and standard solvents. For toluene, n-hexane and chloroform 36.2, 50.9 and 34.2 mN/m were measured at 20°C, which is in a good agreement with data from the literature. For a slug of hexane in contact with a slug of pure water containing ethanol in a concentration range between 0 and 70 (v/v %), a difference of up to 6 mN/m was found, when compared to commercial ring tensiometry. This discrepancy is still under debate.

The influence of heat treatment on the phase relations in mineral growth systems

ABSTRACT Corundum is one of the most famous gems materials. Different heat treatment methods for enhancement purposes are commonly applied and accepted in the gem market. With this reason, the identification of the natural, unheated corundum is intensively investigated. In this study, aluminium hydroxide minerals and zircon are focused to observe the crystallization and phase change of these minerals during heat treatment procedures. Aluminium hydroxide minerals can be transformed to alumina with the corundum structure by heating. The reaction history of aluminium hydroxide minerals containing corundum was investigated comparing it with diaspore, boehmite, gibbsite and bayerite by TG and DTA methods. These hydroxide minerals were entirely transformed to corundum after heating at 600°C. Zircon inclusions in corundums from Ilakaka, Madagascar, were investigated for the influence of different heat-treatment temperatures on the recovery of their crystalline structure and on possible reactions within and with the host crystals. The host corundum was heated at 500, 800, 1000, 1200, 1400, 1600 and 1800°C. The crystallinity, the trapped pressure, and the decomposition of the zircon inclusions within the host corundum have been investigated by Raman spectroscopy. Radiation-damaged zircon inclusions may be used as an indicator for unheated Ilakaka corundum crystals. They are fully recrystallized after heating at 1000°C influencing the lowering of the 3 Raman band shift, the decreasing of FWHM of the 3 Raman band and the decreasing of the trapped pressure between the inclusion and the host corundum. Under microscopic observation, surface alterations of the inclusions can be firstly seen from transparent into frosted-like appearance at 1400°C. Then, between 1600°C and 1800 °C, the inclusion becomes partly or even completely molten. The decomposition of the zircon inclusion to m-ZrO2 and SiO2-glass phases begins at the rim of the inclusion after heating from 1200°C to 1600°C which can be detected by the surface change, the increase of the 3 Raman band position and the trapped pressure. At 1800°C, the zircon inclusions entirely melt transforming to solid phases during cooling like m-ZrO2 and SiO2-glass accompanied by an increase of pressure between the transformed inclusion and its host.

External drivers of biogeochemical cycles in a tropical montane forest in Ecuador

Successful conservation of tropical montane forest, one of the most threatened ecosystems on earth, requires detailed knowledge of its biogeochemistry. Of particular interest is the response of the biogeochemical element cycles to external influences such as element deposition or climate change. Therefore the overall objective of my study was to contribute to improved understanding of role and functioning of the Andean tropical montane forest. In detail, my objectives were to determine (1) the role of long-range transported aerosols and their transport mechanisms, and (2) the role of short-term extreme climatic events for the element budget of Andean tropical forest. In a whole-catchment approach including three 8-13 ha microcatchments under tropical montane forest on the east-exposed slope of the eastern cordillera in the south Ecuadorian Andes at 1850-2200 m above sea level I monitored at least in weekly resolution the concentrations and fluxes of Ca, Mg, Na, K, NO3-N, NH4-N, DON, P, S, TOC, Mn, and Al in bulk deposition, throughfall, litter leachate, soil solution at the 0.15 and 0.3 m depths, and runoff between May 1998 and April 2003. I also used meteorological data from my study area collected by cooperating researchers and the Brazilian meteorological service (INPE), as well as remote sensing products of the North American and European space agencies NASA and ESA. My results show that (1) there was a strong interannual variation in deposition of Ca [4.4-29 kg ha-1 a-1], Mg [1.6-12], and K [9.8-30]) between 1998 and 2003. High deposition changed the Ca and Mg budgets of the catchments from loss to retention, suggesting that the additionally available Ca and Mg was used by the ecosystem. Increased base metal deposition was related to dust outbursts of the Sahara and an Amazonian precipitation pattern with trans-regional dry spells allowing for dust transport to the Andes. The increased base metal deposition coincided with a strong La Niña event in 1999/2000. There were also significantly elevated H+, N, and Mn depositions during the annual biomass burning period in the Amazon basin. Elevated H+ deposition during the biomass burning period caused elevated base metal loss from the canopy and the organic horizon and deteriorated already low base metal supply of the vegetation. Nitrogen was only retained during biomass burning but not during non-fire conditions when deposition was much smaller. Therefore biomass burning-related aerosol emissions in Amazonia seem large enough to substantially increase element deposition at the western rim of Amazonia. Particularly the related increase of acid deposition impoverishes already base-metal scarce ecosystems. As biomass burning is most intense during El Niño situations, a shortened ENSO cycle because of global warming likely enhances the acid deposition at my study forest. (2) Storm events causing near-surface water flow through C- and nutrient-rich topsoil during rainstorms were the major export pathway for C, N, Al, and Mn (contributing >50% to the total export of these elements). Near-surface flow also accounted for one third of total base metal export. This demonstrates that storm-event related near-surface flow markedly affects the cycling of many nutrients in steep tropical montane forests. Changes in the rainfall regime possibly associated with global climate change will therefore also change element export from the study forest. Element budgets of Andean tropical montane rain forest proved to be markedly affected by long-range transport of Saharan dust, biomass burning-related aerosols, or strong rainfalls during storm events. Thus, increased acid and nutrient deposition and the global climate change probably drive the tropical montane forest to another state with unknown consequences for its functions and biological diversity.

Mapping the elastic response of epithelial apical cell membranes suspended across porous array

As the elastic response of cell membranes to mechanical stimuli plays a key role in various cellular processes, novel biophysical strategies to quantify the elasticity of native membranes under physiological conditions at a nanometer scale are gaining interest. In order to investigate the elastic response of apical membranes, elasticity maps of native membrane sheets, isolated from MDCK II (Madine Darby Canine kidney strain II) epithelial cells, were recorded by local indentation with an Atomic Force Microscope (AFM). To exclude the underlying substrate effect on membrane indentation, a highly ordered gold coated porous array with a pore diameter of 1.2 μm was used to support apical membranes. Overlays of fluorescence and AFM images show that intact apical membrane sheets are attached to poly-D-lysine coated porous substrate. Force indentation measurements reveal an extremely soft elastic membrane response if it is indented at the center of the pore in comparison to a hard repulsion on the adjacent rim used to define the exact contact point. A linear dependency of force versus indentation (-dF/dh) up to 100 nm penetration depth enabled us to define an apparent membrane spring constant (kapp) as the slope of a linear fit with a stiffness value of for native apical membrane in PBS. A correlation between fluorescence intensity and kapp is also reported. Time dependent hysteresis observed with native membranes is explained by a viscoelastic solid model of a spring connected to a Kelvin-Voight solid with a time constant of 0.04 s. No hysteresis was reported with chemically fixated membranes. A combined linear and non linear elastic response is suggested to relate the experimental data of force indentation curves to the elastic modulus and the membrane thickness. Membrane bending is the dominant contributor to linear elastic indentation at low loads, whereas stretching is the dominant contributor for non linear elastic response at higher loads. The membrane elastic response was controlled either by stiffening with chemical fixatives or by softening with F-actin disrupters. Overall, the presented setup is ideally suitable to study the interactions of the apical membrane with the underlying cytoskeleton by means of force indentation elasticity maps combined with fluorescence imaging.

Magnetization dynamics in spin valves

Key technology applications like magnetoresistive sensors or the Magnetic Random Access Memory (MRAM) require reproducible magnetic switching mechanisms. i.e. predefined remanent states. At the same time advanced magnetic recording schemes push the magnetic switching time into the gyromagnetic regime. According to the Landau-Lifschitz-Gilbert formalism, relevant questions herein are associated with magnetic excitations (eigenmodes) and damping processes in confined magnetic thin film structures.rnObjects of study in this thesis are antiparallel pinned synthetic spin valves as they are extensively used as read heads in today’s magnetic storage devices. In such devices a ferromagnetic layer of high coercivity is stabilized via an exchange bias field by an antiferromagnet. A second hard magnetic layer, separated by a non-magnetic spacer of defined thickness, aligns antiparallel to the first. The orientation of the magnetization vector in the third ferromagnetic NiFe layer of low coercivity - the freelayer - is then sensed by the Giant MagnetoResistance (GMR) effect. This thesis reports results of element specific Time Resolved Photo-Emission Electron Microscopy (TR-PEEM) to image the magnetization dynamics of the free layer alone via X-ray Circular Dichroism (XMCD) at the Ni-L3 X-ray absorption edge.rnThe ferromagnetic systems, i.e. micron-sized spin valve stacks of typically deltaR/R = 15% and Permalloy single layers, were deposited onto the pulse leading centre stripe of coplanar wave guides, built in thin film wafer technology. The ferromagnetic platelets have been applied with varying geometry (rectangles, ellipses and squares), lateral dimension (in the range of several micrometers) and orientation to the magnetic field pulse to study the magnetization behaviour in dependence of these magnitudes. The observation of magnetic switching processes in the gigahertz range became only possible due to the joined effort of producing ultra-short X-ray pulses at the synchrotron source BESSY II (operated in the so-called low-alpha mode) and optimizing the wave guide design of the samples for high frequency electromagnetic excitation (FWHM typically several 100 ps). Space and time resolution of the experiment could be reduced to d = 100 nm and deltat = 15 ps, respectively.rnIn conclusion, it could be shown that the magnetization dynamics of the free layer of a synthetic GMR spin valve stack deviates significantly from a simple phase coherent rotation. In fact, the dynamic response of the free layer is a superposition of an averaged critically damped precessional motion and localized higher order spin wave modes. In a square platelet a standing spin wave with a period of 600 ps (1.7 GHz) was observed. At a first glance, the damping coefficient was found to be independent of the shape of the spin-valve element, thus favouring the model of homogeneous rotation and damping. Only by building the difference in the magnetic rotation between the central region and the outer rim of the platelet, the spin wave becomes visible. As they provide an additional efficient channel for energy dissipation, spin waves contribute to a higher effective damping coefficient (alpha = 0.01). Damping and magnetic switching behaviour in spin valves thus depend on the geometry of the element. Micromagnetic simulations reproduce the observed higher-order spin wave mode.rnBesides the short-run behaviour of the magnetization of spin valves Permalloy single layers with thicknesses ranging from 3 to 40 nm have been studied. The phase velocity of a spin wave in a 3 nm thick ellipse could be determined to 8.100 m/s. In a rectangular structure exhibiting a Landau-Lifschitz like domain pattern, the speed of the field pulse induced displacement of a 90°-Néel wall has been determined to 15.000 m/s.rn

Zur Darstellung und Interpretation archäologischer und geowissenschaftlicher Untersuchungen anhand einer Auswahl römischer Gebrauchskeramik aus dem Limeskastell Saalburg

Die vorliegende Arbeit gliedert sich in drei Kapitel. Das erste Kapitel umfasst dabei die Darstellung von Methoden, die zum gegenwärtigen Zeitpunkt unter anderem in der provinzialrömischen Archäologie zur Untersuchung von Gefäßkeramik üblich sind, wobei die Einzelergebnisse des im Rahmen dieser Arbeit untersuchten gebrauchskeramischen Materials (Randfragmente) der Saalburg (bei Bad Homburg) am Ende des Kapitels zusammengefasst werden. Im zweiten Kapitel werden anhand des gleichen Materials einige naturwissenschaftliche Methoden dargestellt, die zur Materialanalyse sowohl in den Geowissenschaften (Materialwissenschaft), als auch in der Archäometrie häufig Anwendung finden und deren Ergebnisse am Ende des Kapitels zusammengefasst. In einer Gesamtbetrachtung (drittes Kapitel) werden schließlich diese hinsichtlich ihrer Aussagekraft in archäologischem Kontext evaluiert. Neben der im Anhang festgehaltenen Original-dokumentation der Dünnschliff-Untersuchungen (Ramanspektroskopie, „RS“), werden im Abbildungsteil die Kopien der Originaldaten aus der Röntgendiffraktometrie („XRD“) und der Röntgenfluoreszenzanalyse („RFA“, chemische Analyse), Abbildungen einiger Festkörper, als auch Zeichnungen, Photos und Dünnschliffe der Randfragmente aufgeführt. Während die Darstellung der angewandten Methoden einer Verständniserleichterung vor allem der komplexen chemisch-physikalischen Zusammenhänge dienen soll - nicht zuletzt auch, um die künftige Methodenwahl zu optimieren - soll mittels der Evaluation, vor allem für die Keramikforschung, die Entwicklung neuer Forschungsmethoden unterstützt werden. Aus dem Vergleich der Ergebnisse beider Kapitel erhebt sich nicht allein für die Keramikforschung die Frage, inwieweit die Anwendungen bestimmter Untersuchungen überhaupt sinnvoll sind, wenn sie nicht nur der Bestätigung dienen sollen, sondern welche Konsequenzen daraus auch für die Untersuchung anderer historisch-kultureller Materialgruppen resultieren könnten.