Proton-conducting copolymers, blends and composites with phosphonic acid as protogenic group

ABSTRACT: In this work, proton conducting copolymers, polymer blends and composites containing phosphonic acid groups have been prepared. Proton conduction mechanisms in these materials are discussed respectively in both, the anhydrous and humidified state. Atom transfer radical copolymerization (ATRCP) of diisopropyl-p-vinylbenzyl phosphonate (DIPVBP) and 4-vinyl pyridine (4VP) is studied for the first time in this work. The kinetic parameters are obtained by using the 1H-NMR online technique. Proton conduction in poly(vinylbenzyl phosphonic acid) (PVBPA) homopolymer and its statistical copolymers with 4-vinyl pyridine (poly(VBPA-stat-4VP)s) are comprehensively studied in both, the “dry” and “wet” state. Effects of temperature, water content and polymer composition on proton conductivities are studied and proton transport mechanisms under various conditions are discussed. The proton conductivity of the polymers is in the range of 10-6-10-8 S/cm in nominally dry state at 150 oC. However, proton conductivity of the polymers increases rapidly with water content in the polymers which can reach 10-2 S/cm at the water uptake of 25% in the polymers. The highest proton conductivity obtained from the polymers can even reach 0.3 S/cm which was measured at 85oC with 80% relative humidity in the measuring atmosphere. Poly(4-vinyl pyridine) was grafted from the surface of SiO2 nanoparticles using ATRP in this work for the first time. Following this approach, silica nanoparticles with a shell of polymeric layer are used as basic particles in a polymeric acidic matrix. The proton conductivities of the composites are studied under both, humidified and dry conditions. In dry state, the conductivity of the composites is in the range of 10-10~10-4 S/cm at 150 oC. While in humid state, the composites show much higher proton conductivity. The highest proton conductivity obtained with the composites is 0.5 S/cm measured at 85oC with 80% relative humidity in the measuring atmosphere. The miscibility of poly (vinyl phosphonic acid) and PEO is studied for the first time in this work and a phase diagram is plotted based on a DSC study and optical microscopy. With this knowledge, homogeneous PVPA/PEO mixtures are prepared as proton-conducting polymer blends. The mobility of phosphonic acid groups and PEO in the blends is determined by 1H-MAS-NMR in temperature dependent measurements. The effect of composition and the role of PEO on proton conduction are discussed.

Untersuchung des Reorientierungsverhaltens und Strukturierung dünner amphiphiler Blockcopolymerfilme zum Aufbau von Kompositen

Grundlage für die hier gezeigte Arbeit stellt die Eigenschaft von amphiphilen Blockcopolymeren dar immer den Block mit der niedrigsten Grenzflächenenergie zum angrenzenden Medium an die Oberfläche zu bringen. Durch einen Austausch des Mediums an der Grenzfläche zum Blockcopolymer kann eine Reorientierung erzwungen werden, wenn die Grenzflächenenergie des anderen Blocks nun die niedrigere Grenzflächenenergie besitzt. Dieses Verhalten von dünnen amphiphilen Blockcopolymerfilmen wurde zur Strukturierung von Oberflächen ausgenutzt und in nachfolgenden Synthesen weiter verstärkt. Um dies zu erreichen wurde das zur Strukturierung erforderliche Poly(4-Octylstyrol)block(4-hydroxystyrol) durch kontrollierte radikalische Polymerisationsmethode mit dem Tempo Unimer (2,2,6,6-Tetramethyl-1-1(1-phenyl-ethoxy)-piperidin) synthetisiert. Für die geplanten Reorientierungen und Modifizierungen von Oberflächen wurden dünne Filme durch Schleuderbeschichtung auf verschiedenen Substraten (Siliziumwafern, Glassubstraten und Goldoberflächen) hergestellt. Das Verhalten der Oberflächen von diesen Filmen wurde durch Kontaktwinkelmessungen untersucht. Auf diese Weise konnte gezeigt werden, dass die Oberfläche von Polymerfilmen nach der Präparation aus dem hydrophoben Block des Polymers gebildet wird. Durch Kontakt des Polymerfilms mit Wasser kann dieser zur Reorientierung gebracht werden, so dass der hydrophile Block des Polymers an der Oberfläche erscheint. Dieses Verhalten wurde zur Strukturierung mit softlithographischen Techniken genutzt. Dazu wurden hydrophil/hydrophob strukturierte Oberflächen durch Aufsetzen von hydrophoben PDMS-Stempeln, die Teile der Oberfläche selektiv abdeckten, und Einbringen von Wasser in die dabei entstehenden Kapillaren hergestellt. Dies ermöglichte es die Oberfläche selektiv im Größenbereich von 500nm bis zu 50µm zu strukturieren und an den reaktiven Bereichen Materialien, wie z.B. Kupfer, Titandioxid, Polyelektrolyte, photonische Kristalle und angegraftete Polymere, mit verschiedenen Methoden selektiv auf die Oberfläche aufzubringen. Um den Reorganisationsprozess der Oberfläche genauer zu studieren, wurde ein für diese Aufgabe besser geeignetes Polymer (Poly(Styrol)-block-poly(essigsäure-2-(2-(4-vinyl-phenoxy)-ethoxy)ethylester)) synthetisiert. Aus diesem Blockcopolymer wurden wieder dünne Filme durch Spincoaten hergestellt. Die Reorientierung dieses Polymers in 70°C warmen Wasser konnte durch Kontaktwinkelmessungen und NEXAFS Spektroskopie nachgewiesen werden. Mit Hilfe der NEXAFS Spektroskopie konnte festgestellt werden, dass die Geschwindigkeit der Reorientierung durch eine exponentielle Funktion beschrieben werden kann. Eine Auswertung der Geschwindigkeitskonstante für die Reorientierung einer hydrophilen zu einer hydrophoben Oberfläche des Polymers bei 60°C führt zu =75min. Aufgrund des exponentiellen Charakters der Reorientierung macht es den Anschein, dass die Reorientierung bei verschiedenen Reorientierungstemperaturen bis zu einem gewissen Grad erfolgt und dann stoppt. Eine weitere Reorientierung scheint erst wieder bei einer Temperaturerhöhung zu beginnen. Aus AFM Messungen ist ein Beginnen der Reorientierung durch Bildung kleiner Löcher in der Polymeroberfläche zu erkennen, die sich zu runden Erhöhungen und Vertiefungen vergrößern, um letztendlich in ein spinodales Entmischungsmuster über zu gehen. Dieses heilt dann im Laufe der Zeit langsam durch Verschwinden der hydrophilen Bereiche langsam aus. Der Beginn des zuvor beschriebenen Reorientierungsprozesses einer hydrophilen Oberfläche in eine hydrophobe konnte sowohl in den AFM, als auch in den NEXAFS-Messungen zu ca. 50°C bestimmt werden.

Synthesis, characterization and chemical modification of a cationic polyelectrolyte poly(methylene amine)

Polyamine polymers have attracted attention due to their ability to demonstrate pH dependent cationic nature and presence of highly reactive pendant amino groups. These amino groups make them suitable for a host of applications through cross-linking and derivatization. As a result the end use application of a polyamine is largely driven by the number of amino groups and the way they are attached to the polymer backbone. Thus, this piece of work describes the synthesis and investigation of properties of a novel aliphatic polyamine, poly(methylene amine); that carries maximum number of amino group on its backbone. The target polymer, poly(methylene amine); was synthesized via two major steps viz.1.synthesis of precursor polymers of poly(methylene amine) and 2. Hydrolysis of the precursor polymers to obtain poly(methylene amine). The precursor polymers poly (1,3-diacetylimidazole-2-one)(6) and poly(1,3-diformyldihydroimidazol-2-one)(7) were synthesized via radical polymerization of their respective monomers. The monomers were polymerized in bulk as well as in solution at different reaction conditions. The maximum molecular weights were achieved by polymerizing the monomers in bulk (Mn = 6.5 x 104 g/mol and Mw = 2.13 x 105 g/mol) of 6. The precursor polymers were hydrolyzed under strong reaction conditions in ethanol in presence of NaOH, LiCl at 170°C to yield poly(methylene amine). The process of hydrolysis was monitored by IR spectroscopy. The solution properties of poly(methylene amine) and its hydrochloride were investigated by viscosimetry and light scattering. The reduced viscosity of poly (methylene amine) hydrochloride as a function of polymer concentration demonstrated a behavior typical of cationic polyelectrolyte. With decrease in polymer concentration the reduced viscosity of poly(methylene amine) hydrochloride increased gradually. The dynamic light scattering studies also revealed behaviors of a polyelectrolyte. Poly(methylene amine) was reacted with electrophiles to yield novel materials. While the attachment of alkyl group onto the nitrogen would increase nucleophilicity, it would also impose steric hindrance. As a result the degree of substitution on poly(methylene amine) would be governed by both the factors. Therefore, few model reactions with electrophiles were performed on polvinylamine under similar reaction conditions in order to make a comparative evaluation. It was found that under similar reaction conditions the degree of substitution was higher in case of polyvinylamine in comparison with poly (methylene amine).This shows that the steric hindrance outweighs nucleophilicity while deciding degree of substitution of electrophiles on poly(methylene amine). The modification was further extended to its use as an initiator for ring opening polymerization of benzyloxy protected N-carboxyanhydride of z-Lysine. The resulting polymer had an interesting brush like architecture. The solid state morphology of this polymer was investigated by SAXS. The 2D-WAXS diffractograms revealed hexagonal morphology of peptide segments without formation of alpha helices.

Solid-state NMR investigation of phosphonic acid based proton conducting materials

In this work, new promising proton conducting fuel cell membrane materials were characterized in terms of their structure and dynamic properties using solid-state nuclear magnetic resonance (NMR) spectroscopy and X-ray diffraction. Structurally different, phosphonic acid (PA) containing materials were systematically evaluated for possible high-temperature operation (e.g. at T>100°C). Notably, 1H, 2H and 31P magic angle spinning (MAS) NMR provided insight into local connectivities and dynamics of the hydrogen bonded network, while packing arrangements were identified by means of heteronuclear dipolar recoupling techniques.rnThe first part of this work introduced rather crystalline, low molecular weight ionomers for proton conducting membranes, where six different geometries such as line, triangle, screw, tetrahedron, square and hexagon, were investigated. The hexagon was identified as the most promising geometry with high-temperature bulk proton conductivities in the range of 10-3 Scm-1 at a relative humidity of 50%. However, 2H NMR and TGA-MS data suggest that the bulk proton transport is mainly due to the presence of crystal water. Single crystal X-ray data revealed that in the tetrahedron phosphonic acids form tetrameric clusters isolating the mobile protons while the phosphonic acids in the hexagon form zigzag-type pathways through the sample.rnThe second part of this work demonstrates how acid-base pairing and the choice of appropriate spacers may influence proton conduction. Different ratios of statistical copolymers of poly (vinylphosphonic acid) and poly (4-vinylpyridine) were measured to derive information about the local structure and chemical changes. Though anhydrous proton conductivities of all statistical copolymers are rather poor, the conductivity increases to 10-2 S cm-1 when exposing the sample to relative humidity of 80%. In contrast to PVPA, anhydride formation of phosphonic acids in the copolymer is not reversible even when exposing the sample to a relative humidity of 100%.rnIn addition, the influence of both spacers and degree of backbone crystallinity on bulk proton conductivity was investigated. Unlike in systems such as poly benzimidazole (PBI), spacers were inserted between the protogenic groups along the backbone. It was found that dilution of the protogenic groups decreases the conductivity, but compared to PVPA, similar apparent activation energies for local motions were obtained from both variable temperature 1H NMR and impedance spectroscopy data. These observations suggest the formation of phosphonic acid clusters with high degrees of local proton motion, where only a fraction of motions contribute to the observable bulk proton conductivity. Additionally, it was shown that gradual changes of the spacer length lead to different morphologies.rnIn summary, applying advanced solid-state NMR and X-ray analysis, structural and dynamic phenomena in proton conducting materials were identified on a molecular level. The results were discussed with respect to different proton conduction mechanisms and may contribute to a more rational design or improvement of proton conducting membranes.rn

From anionic polymerization in continuous flow to macromolecular architectures and stimuli-responsive surfaces

The thesis can be divided in four parts and summarized as follows:(i) The investigation and development of a continuous flow synthesis procedure affording end-functional polymers by anionic polymerization and subsequent termination in one reaction step and on a multigram scale was carried out. Furthermore, the implementation of not only a single hydroxyl but multiple orthogonal functionalities at the chain terminus was achieved by utilizing individually designed, functional epoxide-based end-capping reagents.(ii) In an additional step, the respective polymers were used as macroinitiators to prepare in-chain functionalized block copolymers and star polymers bearing intriguing novel structural and material properties. Thus, the second part of this thesis presents the utilization of end-functional polymers as precursors for the synthesis of amphiphilic complex and in some cases unprecedented macromolecular architectures, such as miktoarm star polymers based on poly(vinyl pyridine), poly(vinyl ferrocene) and PEO.(iii) Based on these structures, the third part of this thesis represents a detailed investigation of the preparation of stimuli-responsive ultrathin polymer films, using amphiphilic junction point-reactive block copolymers. The single functionality at the block interface can be employed as anchor group for the covalent attachment on surfaces. Furthermore, the change of surface properties was studied by applying different external stimuli.(iv) An additional topic related to the oxyanionic polymerizations carried out in the context of this thesis was the investigation of viscoelastic properties of different hyperbranched polyethers, inspired by the recent and intense research activities in the field of biomedical applications of multi-functional hyperbranched materials.

New proton conducting membranes for fuel cell applications

In order to synthesize proton-conducting materials which retain acids in the membrane during fuel cell operating conditions, the synthesis of poly(vinylphosphonic acid) grafted polybenzimidazole (PVPA grafted PBI) and the fabrication of multilayer membranes are mainly focussed in this dissertation. Synthesis of PVPA grafted PBI membrane can be done according to "grafting through" method. In "grafting through" method (or macromonomer method), monomer (e.g., vinylphosphonic acid) is radically copolymerized with olefin group attached macromonomer (e.g., allyl grafted PBI and vinylbenzyl grafted PBI). This approach is inherently limited to synthesize graft-copolymer with well-defined architectural and structural parameters. The incorporation of poly(vinylphosphonic acid) into PBI lead to improvements in proton conductivity up to 10-2 S/cm. Regarding multilayer membranes, the proton conducting layer-by-layer (LBL) assembly of polymers by various strong acids such as poly(vinylphosphonic acid), poly(vinylsulfonic acid) and poly(styrenesulfonic acid) paired with basic polymers such as poly(4-vinylimidazole) and poly(benzimidazole), which are appropriate for ‘Proton Exchange Membranes for Fuel Cell’ applications have been described. Proton conductivity increases with increasing smoothness of the film and the maximum measured conductivity was 10-4 S/cm at 25°C. Recently, anhydrous proton-conducting membranes with flexible structural backbones, which show proton-conducting properties comparable to Nafion have been focus of current research. The flexible backbone of polymer chains allow for a high segmental mobility and thus, a sufficiently low glass transition temperature (Tg), which is an essential factor to reach highly conductive systems. Among the polymers with a flexible chain backbone, poly(vinylphosphonic acid), poly(vinylbenzylphosphonic acid), poly(2-vinylbenzimidazole), poly(4-styrenesulfonic acid), poly(4-vinylimidazole), poly(4-vinylimidazole-co-vinylphosphonic acid) and poly(4-vinylimidazole-co-4-styrenesulfonic acid) are interesting materials for fuel cell applications. Synthesis of polybenzimidazole with anthracene structural unit was carried out in order to avoid modification reaction in the imidazole ring, because anthracene would encourage the modification reaction with an olefin by Diels-Alder reaction.

A photophysical study of excited state dynamics in donor-acceptor copolymer photovoltaic blends

This thesis deals with the investigation of charge generation and recombination processes in three different polymer:fullerene photovoltaic blends by means of ultrafast time-resolved optical spectroscopy. The first donor polymer, namely poly[N-11"-henicosanyl-2,7-carbazole-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)] (PCDTBT), is a mid-bandgap polymer, the other two materials are the low-bandgap donor polymers poly[2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b']-dithiophene)-alt-4,7-(2,1,3-benzothiadiazole) (PCPDTBT) and poly[(4,4'-bis(2-ethylhexyl)dithieno[3,2-b:2',3'-d]silole)-2,6-diyl-alt-(2,1,3-benzothiadiazole)-4,7-diyl] (PSBTBT). Despite their broader absorption, the low-bandgap polymers do not show enhanced photovoltaic efficiencies compared to the mid-bandgap system.rnrnTransient absorption spectroscopy revealed that energetic disorder plays an important role in the photophysics of PCDTBT, and that in a blend with PCBM geminate losses are small. The photophysics of the low-bandgap system PCPDTBT were strongly altered by adding a high boiling point cosolvent to the polymer:fullerene blend due to a partial demixing of the materials. We observed an increase in device performance together with a reduction of geminate recombination upon addition of the cosolvent. By applying model-free multi-variate curve resolution to the spectroscopic data, we found that fast non-geminate recombination due to polymer triplet state formation is a limiting loss channel in the low-bandgap material system PCPDTBT, whereas in PSBTBT triplet formation has a smaller impact on device performance, and thus higher efficiencies are obtained.rn

Synthese und Struktur-Eigenschafts-Beziehungen von Oligo- und Poly(2,5-dipropoxy-1,4-phenylenethinylen)en

Oligomere mit konjugierten pi-Elektronensystemen sind für die Materialwissenschaften von großer Bedeutung. Die vielfältigen und umfangreichen Forschungen auf diesem Gebiet gründen im Potenzial dieser Substanzklassen, das im Bereich der Laserfarbstoffe, Leuchtdioden, Photoleiter, optische Schalter oder auch der molekularen Elektronik angesiedelt ist. Zu diesen gehören auch die in dieser Arbeit synthetisierten und untersuchten Phenylenethinylene. Die Herstellung der Oligomere erfolgt nach der Methode von Sonogashira und Hagihara. Dabei wird ein Halogenaren mit einer Alkinkomponente zur Reaktion gebracht. Als Katalysator dient dabei ein Gemisch aus Bis(triphenylphosphin-palladiumdichlorid), Kupfer-(I)-iodid und Triphenylphosphin. Verwendung fanden bei der Synthese zwei Arten von Schutzgruppen. Es handelt sich dabei einerseits um die Trimethylsilyl- und die Triisopropylsilyl-Funktion, die unabhängig voneinander in ein System eingeführt werden und selektiv wieder entfernt werden können. Die zweite Art sind die Halogene Brom und Iod, die aufgrund ihrer Eigenschaft vielmehr als 'dormant group' bezeichnet werden müssen. Eine Ethinylierung führt zunächst zur Substitution des Iod- und anschließend des Bromatoms. Die so erhaltenen Oligomere werden mit verschiedenen spektroskopischen Methoden untersucht. Besonderes Interesse liegt dabei auf der Bestimmung der effektiven Konjugationslänge (EKL). Damit ist es möglich, die Länge des konjugierten Systems zu bestimmen, das für die betreffenden Eigenschaften des entsprechenden Polymers maßgeblich ist. Das nichtlineare optische Verhalten der Oligomere wird mittels der Third-Harmonic-Generation-Methode (THG) gemessen. Die resultierende Größe, die Suszeptibilität 3. Ordnung, gibt Aufschluß über mögliche industrielle Anwendungen.