Design, synthesis and photochemical studies of stilbenoid dendrimers

Stilbenoid dendrimers with stilbene in the periphery and stilbene in periphery as well as core were synthesized by convergent approach except 2nd generation dendrimer with stilbene in the periphery as well as in core (D-5). All dendrimers were characterized by standard techniques such as 1H NMR, 13C NMR, MS and IR spectroscopy. The MALDI-TOF technique proved to be very helpful in the identification of the 2nd generation dendrimer (D-5) with a mass of 3231 a.m.u. The dendrimers were designed in such a way that an intramolecular photochemical CC bond formation was favored. As two stilbene units of the same molecule were close enough so they preferred an intramolecular cyclic process except for zero generation dendrimers. Apart from the cycloaddition, some E/Z isomerization and oligomer formation was also observed on irradiation. These processes were observed by 1H NMR and MALDI-TOF MS. The photochemical behavior was also studied by UV absorption spectroscopy. Irradiating by monochromatic light led to an initial E/Z isomerization and by prolonged irradiation, an irreversible cyclic structure was formed. The choice of the wavelength of incident light is very important as irradiation at 320 nm leads to a reversible E/Z isomerization and a non-reversible cyclobutane formation, but irradiation at 340 nm favors the one-way process E Z. The [2+2] cycloaddition of molecule Tm2De was also studied by irradiating thin films on a quartz surface. An AFM image was taken before irradiation, after 3 sec irradiation and after long irradiation (1 hour). AFM studies show that a short irradiation leads to a cyclic structure as formation of hills of about 20-30 nm on the surface. A prolonged irradiation leads to a CC cross linking which can be monitored on AFM images as disappearance of hills. The roughness goes back to an almost smooth surface. These results prove a very complex material transport, which accompanies the reaction in the surface region.

Investigation of a superthermal ultracold neutron source based on a solid deuterium converter for the TRIGA Mainz reactor

Research in fundamental physics with the free neutron is one of the key tools for testing the Standard Model at low energies. Most prominent goals in this field are the search for a neutron electric dipole moment (EDM) and the measurement of the neutron lifetime. Significant improvements of the experimental performance using ultracold neutrons (UCN) require reduction of both systematic and statistical errors.rnThe development and construction of new UCN sources based on the superthermal concept is therefore an important step for the success of future fundamental physics with ultracold neutrons. rnSignificant enhancement of today available UCN densities strongly correlates with an efficient use of an UCN converter material. The UCN converter here is to be understood as a medium which reduces the velocity of cold neutrons (CN, velocity of about 600 m/s) to the velocity of UCN (velocity of about 6 m/s).rnSeveral big research centers around the world are presently planning or constructing new superthermal UCN sources, which are mainly based on the use of either solid deuterium or superfluid helium as UCN converter.rnThanks to the idea of Yu.Pokotilovsky, there exists the opportunity to build competitive UCN sources also at small research reactors of the TRIGA type. Of course these smaller facilities don't promise high UCN densities of several 1000 UCN/cm³, but they are able to provide densities around 100 UCN/cm³ for experiments.rnIn the context of this thesis, it was possible to demonstrate succesfully the feasibility of a superthermal UCN source at the tangential beamport C of the research reactor TRIGA Mainz. Based on a prototype for the future UCN source at the Forschungs-Neutronenquelle Heinz Maier-Leibnitz (FRMII) in munich, which was planned and built in collaboration with the Technical University of Munich, further investigations and improvements were done and are presented in this thesis. rnIn parallel, a second UCN source for the radial beamport D was designed and built. The comissioning of this new source is foreseen in spring 2010.rnAt beamport D with its higher thermal neutron flux, it should be possible to increase the available UCN densities of 4 UCN/cm³ by minimum one order of magnitude.

Nanoparticle preparation process using novel microjet reactor technology for enhancing dissolution rates of poorly water soluble drugs

In this study a novel method MicroJet reactor technology was developed to enable the custom preparation of nanoparticles. rnDanazol/HPMCP HP50 and Gliclazide/Eudragit S100 nanoparticles were used as model systems for the investigation of effects of process parameters and microjet reactor setup on the nanoparticle properties during the microjet reactor construction. rnFollowing the feasibility study of the microjet reactor system, three different nanoparticle formulations were prepared using fenofibrate as model drug. Fenofibrate nanoparticles stabilized with poloxamer 407 (FN), fenofibrate nanoparticles in hydroxypropyl methyl cellulose phthalate (HPMCP) matrix (FHN) and fenofibrate nanoparticles in HPMCP and chitosan matrix (FHCN) were prepared under controlled precipitation using MicroJet reactor technology. Particle sizes of all the nanoparticle formulations were adjusted to 200-250 nm. rnThe changes in the experimental parameters altered the system thermodynamics resulting in the production of nanoparticles between 20-1000 nm (PDI<0.2) with high drug loading efficiencies (96.5% in 20:1 polymer:drug ratio).rnDrug releases from all nanoparticle formulations were fast and complete after 15 minutes both in FaSSIF and FeSSIF medium whereas in mucodhesiveness tests, only FHCN formulation was found to be mucoadhesive. Results of the Caco-2 studies revealed that % dose absorbed values were significantly higher (p<0.01) for FHCN in both cases where FaSSIF and FeSSIF were used as transport buffer.rn