Preparation and study of magnetic thin film based sub-micron structures

Due to its high Curie temperature of 420K and band structure calculations predicting 100% spin polarisation, Sr2FeMoO6 is a potential candidate for spintronic devices. However, the preparation of good quality thin films has proven to be a non-trivial task. Epitaxial Sr2FeMoO6 thin films were prepared by pulsed laser deposition on different substrates. Differing from previous reports a post-deposition annealing step at low oxygen partial pressure (10-5 mbar) was introduced and enabled the fabrication of reproducible, high quality samples. According to the structural properties of the substrates the crystal structure and morphology of the thin films are modified. The close interrelation between the structural, magnetic and electronic properties of Sr2FeMoO6 was studied. A detailed evaluation of the results allowed to extract valuable information on the microscopic nature of magnetism and charge transport. Smooth films with a mean roughness of about 2 nm have been achieved, which is a pre-requisite for a possible inclusion of this material in future devices. In order to establish device-oriented sub-micron patterning as a standard technique, electron beam lithography and focussed ion beam etching facilities have been put into operation. A detailed characterisation of these systems has been performed. To determine the technological prospects of new spintronics materials, the verification of a high spin polarisation is of vital interest. A popular technique for this task is point contact Andreev reflection (PCAR). Commonly, the charge transport in a transparent metal-superconductor contact of nanometer dimensions is attributed solely to coherent transport. If this condition is not fulfilled, inelastic processes in the constriction have to be considered. PCAR has been applied to Sr2FeMoO6 and the Heusler compound Co2Cr0.6Fe0.4Al. Systematic deviations between measured spectra and the standard models of PCAR have been observed. Therefore existing approaches have been generalised, in order to include the influence of heating. With the extended model the measured data was successfully reproduced but the analysis has revealed grave implications for the determination of spin polarisation, which was found to break down completely in certain cases.

Designed functional defects in colloidal photonic crystals: switching, biomonitoring and modified photoluminescence

Es werden zwei komplementäre "bottom-up" Methoden präsentiert, die den kontrollierten Einbau von "intelligenten" planaren Defekten in selbstorganisierte kolloidale photonische Kristalle (KPKs) ermöglichen. Die Defektschicht basiert auf einem funktionellen, nanometer-skalierten dünnen Film, der entweder durch schichtweise ("layer-by-layer") Selbstorganisation und Mikrokontakttransferübertragung oder durch Aufschleudern und einer KPK-Opferfüllung hergestellt wird. Die entwickelten Techniken gestatten die Integration von maßgeschneiderten dünnen Defektfilmen bestehend aus einer enorm großen Vielfalt an Materialien; sie sind kostengünstig und können im größeren Maßstab angewendet werden. Optische Untersuchungen zeigen einen engen, durch den Defekt hervorgerufenen Transmissionszustand in der photonischen Bandlücke. Die Defektwellenlänge hängt von der optischen Dicke der Defektschicht ab. Aktives Schalten der Defektwellenlänge wird erreicht, indem Defektschichten aus Makromolekülen hergestellt werden, die über externe Erreger wie Licht, Temperatur, Redoxzyklen und mechanischen Druck adressiert werden können. Die Ergebnisse der Untersuchungen sind im Einklang mit separat durchgeführten Ellipsometrie-Messungen und theoretischen "scalar wave approximation"-Berechnungen. Darüber hinaus werden KPKs mit funktionellen biomolekularen Defekten vorgestellt. Über Verschiebungen der Defektmode können DNA-Konformationsänderungen, die enantioselektive Einlagerung eines chiralen Antitumormedikaments sowie Enzymaktivitäten optisch beobachtet werden. Die Einlagerung von fluoreszierenden Farbstoffen und Quantenpunkten in Defekt-KPKs führt zu einer eindeutigen, durch die photonische Bandlücke und den Defektzustand hervorgerufenen Modifizierung der Photolumineszenz (PL)-Spektren. Schaltbare PL-Modifizierungen werden detektiert, wenn adressierbare Defekt-KPKs verwendet werden.

Structure formation of amphiphilic molecules at the air,water interface and after film transfer

One of the basic concepts of molecular self-assembly is that the morphology of the aggregate is directly related to the structure and interaction of the aggregating molecules. This is not only true for the aggregation in bulk solution, but also for the formation of Langmuir films at the air/water interface. Thus, molecules at the interface do not necessarily form flat monomolecular films but can also aggregate into multilayers or surface micelles. In this context, various novel synthetic molecules were investigated in terms of their morphology at the air/water interface and in transferred films. rnFirst, the self-assembly of semifluorinated alkanes and their molecular orientation at the air/water interface and in transferred films was studied employing scanning force microscopy (SFM) and Kelvin potential force microscopy. Here it was found, that the investigated semifluorinated alkanes aggregate to form circular surface micelles with a diameter of 30 nm, which are constituted of smaller muffin-shaped subunits with a diameter of 10 nm. A further result is that the introduction of an aromatic core into the molecular structure leads to the formation of elongated surface micelles and thus implements a directionality to the self-assembly. rnSecond, the self-assembly of two different amphiphilic hybrid materials containing a short single stranded desoxyribonucleic acid (DNA) sequence was investigated at the air/water interface. The first molecule was a single stranded DNA (11mer) molecule with two hydrophobically modified 5-(dodec-1-ynyl)uracil nucleobases at the terminal 5'-end of the oligonucleotide sequence. Isotherm measurements revealed the formation of semi-stable films at the air/water interface. SFM imaging of films transferred via Langmuir-Blodgett technique supported this finding and indicated mono-, bi- and multilayer formation, according to the surface pressure applied upon transfer. Within these films, the hydrophilic DNA sequence was oriented towards air covering 95% of the substrate.rnSimilar results were obtained with a second type of amphiphile, a DNA block copolymer. Furthermore, the potential to perform molecular recognition experiments at the air/water interface with these DNA hybrid materials was evaluated.rnThird, polyglycerol ester molecules (PGE), which are known to form very stable foams, were studies. Aim was to elucidate the molecular structure of PGE molecules at the air/water interface in order to comprehend the foam stabilization mechanism. Several model systems mimicking the air/water interface of a PGE foam and methods for a noninvasive transfer were tested and characterized by SFM. It could be shown, that PGE stabilizes the air/water interface of a foam bubble by formation of multiple surfactant layers. Additionally, a new transfer technique, the bubble film transfer was established and characterized by high speed camera imaging.The results demonstrate the diversity of structures, which can be formed by amphiphilic molecules at the air/water interface and after film transfer, as well as the impact of the chemical structure on the aggregate morphology.