Biogenic emission of halocarbons

Within this doctoral thesis, biogenic emissions of several globally relevant halocarbons (methyl chloride, methyl bromide, methyl iodide, dibromomethane, chloroform and bromoform) have been investigated in different environments. An airborne study was focused on the tropical rainforest ecosystem, while shipborne measurements investigated naturally occurring oceanic plankton blooms. Laboratory experiments using dried plant material were made to elucidate abiotic production mechanisms occurring in organic matter. Airborne measurements over the tropical rainforest of Suriname and French Guyana (3 - 6 °N, 51 - 59 °W) revealed net fluxes of 9.5 (± 3.8 2σ) µg m-2 h-1 methyl chloride and 0.35 (± 0.15 2σ) µg m-2 h-1 chloroform emitted in the long dry season (October) 2005. An extrapolation of these numbers to all tropical forests helped to narrow down the range of the recently discovered and poorly quantified methyl chloride source from tropical ecosystems. The value for methyl chloride obtained (1.5 (± 0.6 2σ) Tg yr-1) affirms that the contribution of the tropical forest ecosystem is the major source in the global budget of methyl chloride. The extrapolated global net chloroform flux from tropical forests (56 (± 23 2σ) Gg yr-1) is of minor importance (5 - 10 %) compared to the global sources. A source of methyl bromide from this region could not be verified. The abiotic formation of methyl chloride and methyl bromide from dead plant material was tested in a laboratory study. The release from plant tissue representative of grassland, deciduous forest, agricultural areas and coastal salt marshes (hay, ash, tomato and saltwort) has been monitored. Incubations at different temperatures (25 - 50 °C) revealed significant emissions even at ambient temperature, and that the emissions increased exponentially with temperature. The strength of the emission was found to be additionally dependent on the availability of halide and the methoxyl group within the plant tissue. However, high water content in the plant material was found to inhibit methyl halide emissions. The abiotic nature of the reaction yielding methyl halides was confirmed by its high activation energy calculated via Arrhenius plots. Shipborne measurements of the atmospheric mixing ratios of methyl chloride, methyl bromide, methyl iodide, dibromomethane and bromoform have been conducted along a South Atlantic transect from the 27.01. - 05.02.2007 to characterize halocarbon emissions from a large-scale natural algae bloom encountered off the coast of Argentina. Mixing ratios of methyl chloride and methyl bromide were not significantly affected by the occurrence of the phytoplankton bloom. Emissions of methyl iodide, dibromomethane and bromoform showed pronounced mixing ratio variations, triggered by phytoplankton abundance. Methyl iodide was strongly correlated with dimethyl sulfide throughout the sampled region. A new technique combining satellite derived biomass marker (chlorophyll a) data with back trajectory analysis was successfully used to attribute variations in mixing ratios to air masses, which recently passed over areas of enhanced biological production.

Decay of imprinted surface waves in polymers

CONCLUSIONS The focus of this work was the investigation ofanomalies in Tg and dynamics at polymer surfaces. Thethermally induced decay of hot-embossed polymer gratings isstudied using laser-diffraction and atomic force microscopy(AFM). Monodisperse PMMA and PS are selected in the Mwranges of 4.2 to 65.0 kg/mol and 3.47 to 65.0 kg/mol,respectively. Two different modes of measurement were used:the one mode uses temperature ramps to obtain an estimate ofthe near-surface glass temperature, Tdec,0; the other modeinvestigates the dynamics at a constant temperature aboveTg. The temperature-ramp experiments reveal Tdec,0 valuesvery close to the Tg,bulk values, as determined bydifferential scanning calorimetry (DSC). The PMMA of65.0 kg/mol shows a decreased value of Tg, while the PS samples of 3.47 and 10.3 kg/mol (Mwplots are produced by shifting the decay curves, on the logarithmic time scale,with respect to a reference curve at Tref. From thisprocedure shift factors were extracted. An Arrhenius analysis of the shift factors reveals adecreasing non-Arrhenius (fragile) behavior with molecular weight for PMMA. PS is fragile for all Mw asexpected for linear polymers. Non-Arrhenius behavior allowsone to fit the shift factors to the William-Landel-Ferry(WLF) equation. The WLF parameters for the varying molecular weights ofPMMA and PS were extracted and compared to the values frombulk rheology measurements. Assuming cg1=16+/-2 at Tg, assuggested by Angell, the glass temperature was determinedfrom the dynamic decay experiments. Within the experimentalerrors, the values for Tg,surf(c1=16) and T_g,bulk(c1=16)tend to be smaller than Tdec,0 and Tg,bulk fromtemperature-ramp and DSC measurements, but confirm thecourse of the values with increasing Mw. The comparison of the fragilities (temperaturedependence of the polymer properties at Tg) near the surfaceand in the bulk shows a higher fragility for PS near thesurface, a lower one for PMMA with molecular weights of 4.2and 65.0 kg/mol. The different surface behavior of PS istraced back to a lower degree of cooperation and a largerfree volume fraction.

Cellulose based Lithium ion polymer electrolytes for Lithium batteries

The separator membrane in batteries and fuel cells is of crucial importance for the function of these devices. In lithium ion batteries the separator membrane as well as the polymer matrix of the electrodes consists of polymer electrolytes which are lithium ion conductors. To overcome the disadvantage of currently used polymer electrolytes which are highly swollen with liquids and thus mechanically and electrochemically unstable, the goal of this work is a new generation of solid polymer electrolytes with a rigid backbone and a soft side chain structure. Moreover the novel material should be based on cheap substrates and its synthesis should not be complicated aiming at low overall costs. The new materials are based on hydroxypropylcellulose and oligoethyleneoxide derivatives as starting materials. The grafting of the oligoethyleneoxide side chains onto the cellulose was carried out following two synthetic methods. One is based on a bromide derivative and another based on p-toluolsulfonyl as a leaving group. The side chain reagents were prepared form tri(ethylene glycol) monoethyl ether. In order to improve the mechanical properties the materials were crosslinked. Two different conceptions have been engaged based on either urethane chemistry or photosensitive dimethyl-maleinimide derivatives. PEO - graft - cellulose derivatives with a high degree of substitution between 2,9 and 3,0 were blended with lithium trifluoromethane-sulfonate, lithium bis(trifluorosulfone)imide and lithium tetrafluoroborate. The molar ratios were in the range from 0,02 to 0,2 [Li]/[O]. The products have been characterized with nuclear magnetic resonance (NMR), gel permeation chromatography (GPC) and laserlight scattering (LS) with respect to their degree of substitution and molecular weight. The effect of salt concentration on ionic conductivity, thermal behaviour and morphology has been investiga-ted with impedance spectroscopy, differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). The crosslinking reactions were controlled with dynamic mechanical analysis (DMS). The degree of substitution of our products is varying between 2,8 and 3,0 as determined by NMR. PEO - graft - cellulose derivatives are highly viscous liquids at room temperature with glass transition temperatures around 215 K. The glass transition temperature for the Lithium salt complexes of PEO - graft - cellulose deri-vatives increase with increasing salt content. The maximum conductivity at room temperature is about 10-4 and at 100°C around 10-3 Scm-1. The presence of lithium salt decreases the thermal stability of the complexes in comparison to pure PEO - graft - cellulose derivatives. Complexes heated over 140 – 150°C completely lose their ionic conductivity. The temperature dependence of the conductivity presented as Arrhenius-type plots for all samples is similar in shape and follows a VTF behaviour. This proofs that the ionic transport is closely related to the segmental motions of the polymer chains. Novel cellulose derivatives with grafted oligoethylen-oxide side chains with well-defined chemical structure and high side chain grafting density have been synthesized. Cellulose was chosen as stiff, rod like macromolecule for the backbone while oligoethylen-oxides are chosen as flexible side chains. A maximum grafting density of 3.0 have been obtained. The best conductivity reaches 10-3 Scm-1 at 100°C for a Li-triflate salt complex with a [Li]/[O] ratio of 0.8. The cross-linked complexes containing the lithium salts form elastomeric films with convenient mechanical stability. Our method of cellulose modification is based on relatively cheap and commercially available substrates and as such appears to be a promising alternative for industrial applications.