Effect of multiple sources of disturbance on rocky benthic assemblages in some localities of Salento, Apulia

The first part of my work consisted in samplings conduced in nine different localities of the salento peninsula and Apulia (Italy): Costa Merlata (BR), Punta Penne (BR), Santa Cesarea terme (LE), Santa Caterina (LE), Torre Inserraglio (LE), Torre Guaceto (BR), Porto Cesareo (LE), Otranto (LE), Isole Tremiti (FG). I collected data of species percentage covering from the infralittoral rocky zone, using squares of 50x50 cm. We considered 3 sites for location and 10 replicates for each site, which has been taken randomly. Then I took other data about the same places, collected in some years, and I combined them together, to do a spatial analysis. So I started from a data set of 1896 samples but I decided not to consider time as a factor because I have reason to think that in this period of time anthropogenic stressors and their effects (if present), didn’t change considerably. The response variable I’ve analysed is the covering percentage of an amount of 243 species (subsequently merged into 32 functional groups), including seaweeds, invertebrates, sediment and rock. 2 After the sampling, I have been spent a period of two months at the Hopkins Marine Station of Stanford University, in Monterey (California,USA), at Fiorenza Micheli's laboratory. I've been carried out statistical analysis on my data set, using the software PRIMER 6. My explorative analysis starts with a nMDS in PRIMER 6, considering the original data matrix without, for the moment, the effect of stressors. What comes out is a good separation between localities and it confirms the result of ANOSIM analysis conduced on the original data matrix. What is possible to ensure is that there is not a separation led by a geographic pattern, but there should be something else that leads the differences. Is clear the presence of at least three groups: one composed by Porto cesareo, Torre Guaceto and Isole tremiti (the only marine protected areas considered in this work); another one by Otranto, and the last one by the rest of little, impacted localities. Inside the localities that include MPA(Marine Protected Areas), is also possible to observe a sort of grouping between protected and controlled areas. What comes out from SIMPER analysis is that the most of the species involved in leading differences between populations are not rare species, like: Cystoseira spp., Mytilus sp. and ECR. Moreover I assigned discrete values (0,1,2) of each stressor to all the sites I considered, in relation to the intensity with which the anthropogenic factor affect the localities. 3 Then I tried to estabilish if there were some significant interactions between stressors: by using Spearman rank correlation and Spearman tables of significance, and taking into account 17 grades of freedom, the outcome shows some significant stressors interactions. Then I built a nMDS considering the stressors as response variable. The result was positive: localities are well separeted by stressors. Consequently I related the matrix with 'localities and species' with the 'localities and stressors' one. Stressors combination explains with a good significance level the variability inside my populations. I tried with all the possible data transformations (none, square root, fourth root, log (X+1), P/A), but the fourth root seemed to be the best one, with the highest level of significativity, meaning that also rare species can influence the result. The challenge will be to characterize better which kind of stressors (including also natural ones), act on the ecosystem; and give them a quantitative and more accurate values, trying to understand how they interact (in an additive or non-additive way).

Thermal structure and dynamical modeling of a Mediterranean tropical-like cyclone

In the present work, a detailed analysis of a Mediterranean TLC occurred in January 2014 has been conducted. The author is not aware of other studies regarding this particular event at the publication of this thesis. In order to outline the cyclone evolution, observational data, including weather-stations data, satellite data, radar data and photographic evidence, were collected at first. After having identified the cyclone path and its general features, the GLOBO, BOLAM and MOLOCH NWP models, developed at ISAC-CNR (Bologna), were used to simulate the phenomenon. Particular attention was paid on the Mediterranean phase as well as on the Atlantic phase, since the cyclone showed a well defined precursor up to 3 days before the minimum formation in the Alboran Sea. The Mediterranean phase has been studied using different combinations of GLOBO, BOLAM and MOLOCH models, so as to evaluate the best model chain to simulate this kind of phenomena. The BOLAM and MOLOCH models showed the best performance, by adjusting the path erroneously deviated in the National Centre for Environmental Prediction (NCEP) and ECMWF operational models. The analysis of the cyclone thermal phase shown the presence of a deep-warm core structure in many cases, thus confirming the tropical-like nature of the system. Furthermore, the results showed high sensitivity to initial conditions in the whole lifetime of the cyclone, while the Sea Surface Temperature (SST) modification leads only to small changes in the Adriatic phase. The Atlantic phase has been studied using GLOBO and BOLAM model and with the aid of the same methodology already developed. After tracing the precursor, in the form of a low-pressure system, from the American East Coast to Spain, the thermal phase analysis was conducted. The parameters obtained showed evidence of a deep-cold core asymmetric structure during the whole Atlantic phase, while the first contact with the Mediterranean Sea caused a sudden transition to a shallow-warm core structure. The examination of Potential Vorticity (PV) 3-dimensional structure revealed the presence of a PV streamer that individually formed over Greenland and eventually interacted with the low-pressure system over the Spanish coast, favouring the first phase of the cyclone baroclinic intensification. Finally, the development of an automated system that tracks and studies the thermal phase of Mediterranean cyclones has been encouraged. This could lead to the forecast of potential tropical transition, against with a minimum computational investment.

Stochastic modeling of bacterial protein domains distribution to predict horizontal gene transfer

In questo elaborato, abbiamo tentato di modellizzare i processi che regolano la presenza dei domini proteici. I domini proteici studiati in questa tesi sono stati ottenuti dai genomi batterici disponibili nei data base pubblici (principalmente dal National Centre for Biotechnology Information: NCBI) tramite una procedura di simulazione computazionale. Ci siamo concentrati su organismi batterici in quanto in essi la presenza di geni trasmessi orizzontalmente, ossia che parte del materiale genetico non provenga dai genitori, e assodato che sia presente in una maggiore percentuale rispetto agli organismi più evoluti. Il modello usato si basa sui processi stocastici di nascita e morte, con l'aggiunta di un parametro di migrazione, usato anche nella descrizione dell'abbondanza relativa delle specie in ambito delle biodiversità ecologiche. Le relazioni tra i parametri, calcolati come migliori stime di una distribuzione binomiale negativa rinormalizzata e adattata agli istogrammi sperimentali, ci induce ad ipotizzare che le famiglie batteriche caratterizzate da un basso valore numerico del parametro di immigrazione abbiano contrastato questo deficit con un elevato valore del tasso di nascita. Al contrario, ipotizziamo che le famiglie con un tasso di nascita relativamente basso si siano adattate, e in conseguenza, mostrano un elevato valore del parametro di migrazione. Inoltre riteniamo che il parametro di migrazione sia direttamente proporzionale alla quantità di trasferimento genico orizzontale effettuato dalla famiglia batterica.

Physical characterization and numerical modeling of a WEST-like tokamak divertor plasma

Il presente elaborato è incentrato sulla modellizzazione del plasma di bordo nei dispositivi per la produzione di energia da fusione nucleare noti come tokamak. La tecnologia che nel corso di tutta la seconda metà del XX secolo fino ad oggi è stata sviluppata a questo fine deve necessariamente scontrarsi con alcuni limiti. Nei tokamak il confinamento del plasma è di tipo magnetico e vincola le particelle a muoversi di moto elicoidale all'interno del vessel, tuttavia il confinamento non risulta perfetto e parte dell'energia si scarica sulle pareti della camera, rischiando pertanto di fondere i materiali. Alcune strategie possono essere messe in atto per limitare questo problema, per esempio agendo sulla geometria del tokamak, oppure sulla fisica, inducendo nel plasma una data concentrazione di impurezze che ionizzino irraggiando parte dell'energia di plasma. Proprio tale meccanismo di perdita è stato simulato in un modello monodimensionale di plasma monofluido di bordo. I risultati del codice numerico relativo al modello dimostrano che per concentrazioni di impurezze crescenti è possibile diminuire in modo significativo flusso di calore e temperatura al divertore. Per di più risulta possibile controllare la posizione del fronte di irraggiamento per mezzo di parametri di controllo del plasma quali la pressione. Si osserva inoltre l'insorgere del cosiddetto fenomeno di biforcazione alle basse temperature di divertore, fenomeno in cui il plasma si comporta in modo instabile a causa di fenomeni fisici tipici delle basse energie ("detachment") e a seguito del quale può improvvisamente spegnersi (disruzione). Infine lo stesso modello è stato migliorato inserendo l'ipotesi di plasma bifluido. Anche per gli ioni viene osservato il fenomeno di biforcazione. I risultati numerici evidenziano le dinamiche dello scambio energetico fra le specie gettando le basi di una progettazione efficiente della chimica del plasma finalizzata al raffreddamento del divertore.

Lifetime Modeling of SiC Power Modules in Automotive Traction Inverters

This thesis presents a model-based software implementation for the estimation of the damage of a power module inside and automotive traction inverter with few hardware test setup performed to support the simulation with real-life data.

Centrifuge Modeling of Sandy Slopes

Slope failure occurs in many areas throughout the world and it becomes an important problem when it interferes with human activity, in which disasters provoke loss of life and property damage. In this research we investigate the slope failure through the centrifuge modeling, where a reduced-scale model, N times smaller than the full-scale (prototype), is used whereas the acceleration is increased by N times (compared with the gravity acceleration) to preserve the stress and the strain behavior. The aims of this research “Centrifuge modeling of sandy slopes” are in extreme synthesis: 1) test the reliability of the centrifuge modeling as a tool to investigate the behavior of a sandy slope failure; 2) understand how the failure mechanism is affected by changing the slope angle and obtain useful information for the design. In order to achieve this scope we arranged the work as follows: Chapter one: centrifuge modeling of slope failure. In this chapter we provide a general view about the context in which we are working on. Basically we explain what is a slope failure, how it happens and which are the tools available to investigate this phenomenon. Afterwards we introduce the technology used to study this topic, that is the geotechnical centrifuge. Chapter two: testing apparatus. In the first section of this chapter we describe all the procedures and facilities used to perform a test in the centrifuge. Then we explain the characteristics of the soil (Nevada sand), like the dry unit weight, water content, relative density, and its strength parameters (c,φ), which have been calculated in laboratory through the triaxial test. Chapter three: centrifuge tests. In this part of the document are presented all the results from the tests done in centrifuge. When we talk about results we refer to the acceleration at failure for each model tested and its failure surface. In our case study we tested models with the same soil and geometric characteristics but different angles. The angles tested in this research were: 60°, 75° and 90°. Chapter four: slope stability analysis. We introduce the features and the concept of the software: ReSSA (2.0). This software allows us to calculate the theoretical failure surfaces of the prototypes. Then we show in this section the comparisons between the experimental failure surfaces of the prototype, traced in the laboratory, and the one calculated by the software. Chapter five: conclusion. The conclusion of the research presents the results obtained in relation to the two main aims, mentioned above.

Centrifuge modeling of earth-reinforced retaining walls

Object of this thesis has been centrifuge modelling of earth reinforced retaining walls with modular blocks facing in order to investigate on the influence of design parameters, such as length and vertical spacing of reinforcement, on the behaviour of the structure. In order to demonstrate, 11 models were tested, each one with different length of reinforcement or spacing. Each model was constructed and then placed in the centrifuge in order to artificially raise gravitational acceleration up to 35 g, reproducing the soil behaviour of a 5 metre high wall. Vertical and horizontal displacements were recorded by means of a special device which enabled tracking of deformations in the structure along its longitudinal cross section, essentially drawing its deformed shape. As expected, results confirmed reinforcement parameters to be the governing factor in the behaviour of earth reinforced structures since increase in length and spacing improved structural stability. However, the influence of the length was found out to be the leading parameter, reducing facial deformations up to five times, and the spacing playing an important role especially in unstable configurations. When failure occurred, failure surface was characterised by the same shape (circular) and depth, regardless of the reinforcement configuration. Furthermore, results confirmed the over-conservatism of codes, since models with reinforcement layers 0.4H long showed almost negligible deformations. Although the experiments performed were consistent and yielded replicable results, further numerical modelling may allow investigation on other issues, such as the influence of the reinforcement stiffness, facing stiffness and varying backfills.

Environment of radio sources in the vla-cosmos survey

Sebbene studiati a fondo, i processi che hanno portato alla formazione ed alla evoluzione delle galassie così come sono osservate nell'Universo attuale non sono ancora del tutto compresi. La visione attuale della storia di formazione delle strutture prevede che il collasso gravitazionale, a partire dalle fluttuazioni di densità primordiali, porti all'innesco della formazione stellare; quindi che un qualche processo intervenga e la interrompa. Diversi studi vedono il principale responsabile di questa brusca interruzione della formazione stellare nei fenomeni di attività nucleare al centro delle galassie (Active Galactic Nuclei, AGN), capaci di fornire l'energia necessaria a impedire il collasso gravitazionale del gas e la formazione di nuove stelle. Uno dei segni della presenza di un tale fenomeno all'interno di una galassia e l'emissione radio dovuta ai fenomeni di accrescimento di gas su buco nero. In questo lavoro di tesi si è studiato l'ambiente delle radio sorgenti nel campo della survey VLA-COSMOS. Partendo da un campione di 1806 radio sorgenti e 1482993 galassie che non presentassero emissione radio, con redshift fotometrici e fotometria provenienti dalla survey COSMOS e dalla sua parte radio (VLA-COSMOS), si è stimata la ricchezza dell'ambiente attorno a ciascuna radio sorgente, contando il numero di galassie senza emissione radio presenti all'interno di un cilindro di raggio di base 1 Mpc e di altezza proporzionale all'errore sul redshift fotometrico di ciascuna radio sorgente, centrato su di essa. Al fine di stimare la significatività dei risultati si è creato un campione di controllo costituito da 1806 galassie che non presentassero emissione radio e si è stimato l'ambiente attorno a ciascuna di esse con lo stesso metodo usato per le radio sorgenti. I risultati mostrano che gli ammassi di galassie aventi al proprio centro una radio sorgente sono significativamente più ricchi di quelli con al proprio centro una galassia senza emissione radio. Tale differenza in ricchezza permane indipendentemente da selezioni basate sul redshift, la massa stellare e il tasso di formazione stellare specifica delle galassie del campione e mostra che gli ammassi di galassie con al proprio centro una radio sorgente dovuta a fenomeni di AGN sono significativamente più ricchi di ammassi con al proprio centro una galassia senza emissione radio. Questo effetto e più marcato per AGN di tipo FR I rispetto ad oggetti di tipo FR II, indicando una correlazione fra potenza dell'AGN e formazione delle strutture. Tali risultati gettano nuova luce sui meccanismi di formazione ed evoluzione delle galassie che prevedono una stretta correlazione tra fenomeni di AGN, formazione stellare ed interruzione della stessa.

Finite element modeling of the cement-bone interface beneath the tibial tray of a total knee arthroplasty: Study of the stress shielding effect (modellazione agli elementi finiti dell'interfaccia cemento-osso sotto il piatto tibiale di protesi totale di ginocchio: Analisi dello stress shielding)

The goal of this thesis was the study of the cement-bone interface in the tibial component of a cemented total knee prosthesis. One of the things you can see in specimens after in vivo service is that resorption of bone occurs in the interdigitated region between bone and cement. A stress shielding effect was investigated as a cause to explain bone resorption. Stress shielding occurs when bone is loaded less than physiological and therefore it starts remodeling according to the new loading conditions. µCT images were used to obtain 3D models of the bone and cement structure and a Finite Element Analysis was used to simulate different kind of loads. Resorption was also simulated by performing erosion operations in the interdigitated bone region. Finally, 4 models were simulated: bone (trabecular), bone with cement, and two models of bone with cement after progressive erosions of the bone. Compression, tension and shear test were simulated for each model in displacement-control until 2% of strain. The results show how the principal strain and Von Mises stress decrease after adding the cement on the structure and after the erosion operations. These results show that a stress shielding effect does occur and rises after resorption starts.

Mechanical analysis and modeling of structural archetypes

This is a research B for the University of Bologna. The course is the civil engineering LAUREA MAGISTRALE at UNIBO. The main purpose of this research is to promote another way of explaining, analyzing and presenting some civil engineering aspects to the students worldwide by theory, modeling and photos. The basic idea is divided into three steps. The first one is to present and analyze the theoretical parts. So a detailed analysis of the theory combined with theorems, explanations, examples and exercises will cover this step. At the second, a model will make clear all these parts that were discussed in the theory by showing how the structures work or fail. The modeling is able to present the behavior of many elements, in scale which we use in the real structures. After these two steps an interesting exhibition of photos from the real world with comments will give the chance to the engineers to observe all these theoretical and modeling-laboratory staff in many different cases. For example many civil engineers in the world may know about the air pressure on the structures but many of them have never seen the extraordinary behavior of the bridge of Tacoma ‘dancing with the air’. At this point I would like to say that what I have done is not a book, but a research of how this ‘3 step’ presentation or explanation of some mechanical characteristics could be helpful. I know that my research is something different and new and in my opinion is very important because it helps students to go deeper in the science and also gives new ideas and inspirations. This way of teaching can be used at all lessons especially at the technical. Hope that one day all the books will adopt this kind of presentation.

Assimilation of data from conventional and non conventional networks through a LETKF scheme in the COSMO model

The present work studies a km-scale data assimilation scheme based on a LETKF developed for the COSMO model. The aim is to evaluate the impact of the assimilation of two different types of data: temperature, humidity, pressure and wind data from conventional networks (SYNOP, TEMP, AIREP reports) and 3d reflectivity from radar volume. A 3-hourly continuous assimilation cycle has been implemented over an Italian domain, based on a 20 member ensemble, with boundary conditions provided from ECMWF ENS. Three different experiments have been run for evaluating the performance of the assimilation on one week in October 2014 during which Genova flood and Parma flood took place: a control run of the data assimilation cycle with assimilation of data from conventional networks only, a second run in which the SPPT scheme is activated into the COSMO model, a third run in which also reflectivity volumes from meteorological radar are assimilated. Objective evaluation of the experiments has been carried out both on case studies and on the entire week: check of the analysis increments, computing the Desroziers statistics for SYNOP, TEMP, AIREP and RADAR, over the Italian domain, verification of the analyses against data not assimilated (temperature at the lowest model level objectively verified against SYNOP data), and objective verification of the deterministic forecasts initialised with the KENDA analyses for each of the three experiments.

Finite element modeling of flow/compression-induced deformation of alginate scaffolds for bone tissue engineering

Trauma or degenerative diseases such as osteonecrosis may determine bone loss whose recover is promised by a "tissue engineering“ approach. This strategy involves the use of stem cells, grown onboard of adequate biocompatible/bioreabsorbable hosting templates (usually defined as scaffolds) and cultured in specific dynamic environments afforded by differentiation-inducing actuators (usually defined as bioreactors) to produce implantable tissue constructs. The purpose of this thesis is to evaluate, by finite element modeling of flow/compression-induced deformation, alginate scaffolds intended for bone tissue engineering. This work was conducted at the Biomechanics Laboratory of the Institute of Biomedical and Neural Engineering of the Reykjavik University of Iceland. In this respect, Comsol Multiphysics 5.1 simulations were carried out to approximate the loads over alginate 3D matrices under perfusion, compression and perfusion+compression, when varyingalginate pore size and flow/compression regimen. The results of the simulations show that the shear forces in the matrix of the scaffold increase coherently with the increase in flow and load, and decrease with the increase of the pore size. Flow and load rates suggested for proper osteogenic cell differentiation are reported.