Characterization of innovative kerfless cutting of monocrystalline silicon wafers for photovoltaic applications

Nowadays renewable energies are a hot research topic, and the goal is to improve cell efficiency and reduce production costs, aiming to make the use of photovoltaics increasingly widespread and convenient. Monocrystalline silicon solar cells are leaders in the photovoltaic market. However, market-established cutting techniques produce a consistent amount of material waste when cutting ingots into wafers. The“Stress-induced LIft-Off Method” (SLIM) is emerging in recent years as an alternative, more sustainable separation technique, which reduces material loss and can lead to obtaining increasingly thinner wafers, further reducing the required amount of silicon. This thesis presents the micro-characterization of the separated wafers with the SLIM technique. The wafers were obtained with a two-step procedure. First, a layer of defects was induced in the silicon using ultra-short medium-infrared laser pulses. Then, the material was deposited on one of the sides and induced stress in the silicon, such as to further weaken it. In this way, only rapid cooling is required for detachment to occur. The obtained results indicate that the SLIM-cut technique halves the minority carriers’ lifetime. There is no amorphization, crystal disorder or high-pressure phases. However, changes in the Raman spectra suggest that tensile stress may have been produced on these surface layers by the separation process. The AFM topography highlights surface irregularities, which may be removed with a polishing step. The surface also shows laser-modified regions, which are evident in SEM images, but not in AFM topographies, suggesting a charging effect due to electron bombardment. Lastly, the electrical characterization by conductive AFM lacks any changes in the conductive behaviour of the material where the laser-modified areas should be located. In conclusion, these preliminary results are promising to carry out a systematic characterization of this technique of this innovative SLIM technique.

Piattaforma off-shore : progettazione delle procedure di movement e lifting relative al lower level deck section 1 e section 2

Progettazione delle procedure necessarie alla realizzazione di piattaforme off-shore, grandi e complesse strutture intelaiate di pilastri, diagonali, travi primarie e travi secondarie, progettate per insediarsi in ambiente marino ed idonee ad ospitare impianti per l'estrazione di idrocarburi. Durante la fase di progettazione si procede con l'ideare la struttura della piattaforma fino a definire le caratteristiche di ogni componente: tale fase ha come esito la redazione dei project drawings (disegni di progetto). La fase di realizzazione è quella che interessa propriamente il lavoro svolto: a seguito della progettazione infatti emergono nuove problematiche a livello applicativo e costruttivo che necessitano di essere studiate e risolte preventivamente alla costruzione fisica dell'opera. In particolar modo è necessario definire quali parti della struttura possono essere acquistate e quali invece devono essere realizzate su misura. Definite le modalità costruttive, viene effettuato lo studio riguardante la movimentazione dei vari piani della piattaforma, movement, e successivamente le problematiche relative al sollevamento degli stessi, lifting. Le due procedure necessitano di raffinate valutazioni euristiche ed analitiche per garantire che la struttura non collassi.

Diversity of microbial communities at shallow-hydrothermal vents off Dominica, Lesser Antilles

Hydrothermal vents are often compared to desert oases, because of the presence of highly diverse and abundant biotic communities inhabiting these extreme environments. Nevertheless, the microbial communities associated with shallow-hydrothermal systems have been poorly studied. Hydrothermal activity at Dominica Island is quite well known under the geological and geochemical aspects, but no previous information existed about the microbial communities associated to this area. This thesis is therefore targeting the microbiology of hydrothermal sediments combining geochemical and molecular biological investigations, focusing on differences between hydrothermal vents and background (i.e. control) areas, and between hydrothermal sites. It was also intended to assess relationship between geochemical parameters and microbial diversity at the two hydrothermally impacted sites. Two shallow-sea hydrothermal vents located south-west off Dominica Island (Lesser Antilles) have been investigated in this study: Champagne Hot Springs and Soufriere Bay offshore vent. During this study, sediments for geochemical and molecular analyses were collected every 2 cm from the two impacted areas and from two control sites not associated with hydrothermal activity; in situ temperatures measurements were also taken every 5 cm deep in the sediment for all the sites. A geochemical characterization of the sediment porewater was performed through the analysis of several elements’ concentrations (i.e. H2S, Cl-, Br-, SO42-, Fe2+, Na+, K+, B+, Si+). Microbial communities at the different sites were studied by Automated Intergenic Spacer Analysis (ARISA). Inspection of the operational taxonomic units (OTUs) distribution was performed, as well as statistical analyses for communities’ structure and composition differences, and for changes of β-diversity along with sediment geochemistry. Data suggested that mixing between hydrothermal fluids and seawater results in distinct different environmental gradients and potential ecological niches between the two investigated hydrothermal vents, reflecting a difference in microbial community structures between them.

Studio di fattibilità di una nuova tipologia di argano per il sollevamento di carichi nel settore off-shore

Studio di una nuova tipologia di argano per il sollevamento di carichi nel settore off-shore. In particolare, un argano funzionalmente identico ad uno in fase di realizzazione in azienda è stato modellato al CAD 3D e verificato strutturalmente utilizzando Ansys Workbench, software adatto per analisi F.E.M.. Ottenuti i risultati, ne è stato fatto un confronto con quelli relativi all'argano esistente (argano di ‟Moho‟); nello specifico sono stati comparati gli stress ottenuti nelle varie parti dei due argani (tamburo, spalla, flange, alette di rinforzo, albero) in seguito all‟applicazione di 4 casi di carico differenti (E‟, E‟‟, P‟, P‟‟).