A multi-objective genetic algorithm optimisation using variable speed pumps in water distribution systems

Due to its practical importance and inherent complexity, the optimisation of distribution networks for supplying drinking water has been the subject of extensive study for the past 30 years. The optimization is governed by sizing the pipes in the water distribution network (WDN) and / or optimises specific parts of the network such as pumps, tanks etc. or try to analyse and optimise the reliability of a WDN. In this thesis, the author has analysed two different WDNs (Anytown City and Cabrera city networks), trying to solve and optimise a multi-objective optimisation problem (MOOP). The main two objectives in both cases were the minimisation of Energy Cost (€) or Energy consumption (kWh), along with the total Number of pump switches (TNps) during a day. For this purpose, a decision support system generator for Multi-objective optimisation used. Its name is GANetXL and has been developed by the Center of Water System in the University of Exeter. GANetXL, works by calling the EPANET hydraulic solver, each time a hydraulic analysis has been fulfilled. The main algorithm used, was a second-generation algorithm for multi-objective optimisation called NSGA_II that gave us the Pareto fronts of each configuration. The first experiment that has been carried out was the network of Anytown city. It is a big network with a pump station of four fixed speed parallel pumps that are boosting the water dynamics. The main intervention was to change these pumps to new Variable speed driven pumps (VSDPs), by installing inverters capable to diverse their velocity during the day. Hence, it’s been achieved great Energy and cost savings along with minimisation in the number of pump switches. The results of the research are thoroughly illustrated in chapter 7, with comments and a variety of graphs and different configurations. The second experiment was about the network of Cabrera city. The smaller WDN had a unique FS pump in the system. The problem was the same as far as the optimisation process was concerned, thus, the minimisation of the energy consumption and in parallel the minimisation of TNps. The same optimisation tool has been used (GANetXL).The main scope was to carry out several and different experiments regarding a vast variety of configurations, using different pump (but this time keeping the FS mode), different tank levels, different pipe diameters and different emitters coefficient. All these different modes came up with a large number of results that were compared in the chapter 8. Concluding, it should be said that the optimisation of WDNs is a very interested field that has a vast space of options to deal with. This includes a large number of algorithms to choose from, different techniques and configurations to be made and different support system generators. The researcher has to be ready to “roam” between these choices, till a satisfactory result will convince him/her that has reached a good optimisation point.

Modelli di scambio termico in pozzo sulla base della caratterizzazione geotermica di un reservoir a bassa entalpia: studio di sensitività sulla efficienza dei sistemi di condizionamento a pompa di calore

Tra i temi di attualità, quello del risparmio energetico è tra i più dibattuti negli ultimi anni; tale tema è strettamente correlato al problema del riscaldamento globale, infatti, mentre sul prossimo esaurimento delle risorse energetiche tradizionali non vi sono ancora certezze assolute, per quanto riguarda l’azione nociva dei gas serra, la Comunità Scientifica Internazionale si ritrova d’accordo su una netta presa di posizione contro l’emissione di tali sostanze, provocata in larga parte dall’utilizzo dei combustibili fossili. In questo contesto, l’Unione Europea sta promuovendo la diffusione di tecnologie che non prevedano l’utilizzo di gas, petrolio o carbone, soprattutto per il settore dell’edilizia, ove una corretta progettazione e l’utilizzo di tecnologie non convenzionali può portare alla riduzione anche dell’80% dei consumi, con conseguente abbattimento delle emissioni. Tra questi interventi innovativi, il più comune e conosciuto è sicuramente quello del solare termico e fotovoltaico; ma ne esistono anche di altri, ancora non molto pubblicizzati in Italia, ma ampiamente conosciuti e utilizzati in altri paesi dell’Unione. Tra questi, vi è il sistema di riscaldamento analizzato in questa tesi: la pompa di calore geotermica. Tale sistema, come verrà spiegato nell’elaborato di laurea, ha indubbi vantaggi economici, energetici ed ambientali, a fronte di una non trascurabile spesa iniziale. Attualmente, nel Nord Italia, si incominciano a vedere impianti di questo tipo, sulla scia del successo riscontrato nei paesi confinanti (in particolare Austria e Svizzera). La progettazione si basa attualmente su modelli statici, sviluppati dall’Università Svizzera del Canton Ticino, per l’utilizzo della pompa di calore nel territorio alpino. Obiettivo della tesi, è la verifica di tali modelli, di cui si è venuto a conoscenza grazie alla collaborazione con l’Università SUPSI, sulle condizioni idrogeologiche della Pianura Padana, soffermandosi su alcuni parametri fondamentali della progettazione di una pompa di calore geotermica, quali la conduttività e la capacità termica volumetrica dei terreni incontrati, la presenza di falde, ed i parametri geometrici del pozzo, al fine di dare una valutazione tecnica ed economica dell’impianto. Tali analisi è stata infatti fino ad ora affrontata in maniera sommaria dai perforatori, che eseguono generalmente sempre lo stesso modello di pozzo geotermico, sulla base degli esempi consolidati di Svizzera e Germania. Alcune misure di temperatura in situ sono state rilevate in collaborazione con la società Geotermia SRL di Mantova, ditta specializzata nella perforazione di pozzi geotermici (tale esperienza è parte centrale dell’estratto “Laboratorio di Tesi Ls”), mentre la parte modellistica della tesi è stata sviluppata in collaborazione con lo studio di progettazione Studio Seta SRL di Faenza, il cui stabile è climatizzato in parte con una pompa di calore geotermica.

Development of a fluorescent-based single liposome assay for studying calcium transporter LMCA1

The morphological and functional unit of all the living organisms is the cell. The transmembrane proteins, localized in the plasma membrane of cells, play a key role in the survival of the cells themselves. These proteins perform a variety of different tasks, for example the control of the homeostasis. In order to control the homeostasis, these proteins have to regulate the concentration of chemical elements, like ions, inside and outside the cell. These regulations are fundamental for the survival of the cell and to understand them we need to understand how transmembrane proteins work. Two of the most important categories of transmembrane proteins are ion channels and transporter proteins. The ion channels have been depth studied at the single molecule level since late 1970s with the development of patch-clamp technique. It is not possible to apply this technique to study the transporter proteins so a new technique is under development in order to investigate the behavior of transporter proteins at the single molecule level. This thesis describes the development of a nanoscale single liposome assay for functional studies of transporter proteins based on quantitative fluorescence microscopy in a highly-parallel manner and in real time. The transporter of interest is the prokaryotic transporter Listeria Monocytogenes Ca2+-ATPase1 (LMCA1), a structural analogue of the eukaryotic calcium pumps SERCA and PMCA. This technique will allow the characterization of LMCA1 functionality at the single molecule level. Three systematically characterized fluorescent sensors were tested at the single liposome scale in order to investigate if their properties are suitable to study the function of the transporter of interest. Further studies will be needed in order to characterize the selected calcium sensor and pH sensor both implemented together in single liposomes and in presence of the reconstituted protein LMCA1.

Design and Implementation of Single phase 230V to Three Phase Inverter Based on the Embedded System STM-32 Applied to motor control

In the field of Power Electronics, several types of motor control systems have been developed using STM microcontroller and power boards. In both industrial power applications and domestic appliances, power electronic inverters are widely used. Inverters are used to control the torque, speed, and position of the rotor in AC motor drives. An inverter delivers constant-voltage and constant-frequency power in uninterruptible power sources. Because inverter power supplies have a high-power consumption and low transfer efficiency rate, a three-phase sine wave AC power supply was created using the embedded system STM32, which has low power consumption and efficient speed. It has the capacity of output frequency of 50 Hz and the RMS of line voltage. STM32 embedded based Inverter is a power supply that integrates, reduced, and optimized the power electronics application that require hardware system, software, and application solution, including power architecture, techniques, and tools, approaches capable of performance on devices and equipment. Power inverters are currently used and implemented in green energy power system with low energy system such as sensors or microcontroller to perform the operating function of motors and pumps. STM based power inverter is efficient, less cost and reliable. My thesis work was based on STM motor drives and control system which can be implemented in a gas analyser for operating the pumps and motors. It has been widely applied in various engineering sectors due to its ability to respond to adverse structural changes and improved structural reliability. The present research was designed to use STM Inverter board on low power MCU such as NUCLEO with some practical examples such as Blinking LED, and PWM. Then we have implemented a three phase Inverter model with Steval-IPM08B board, which converter single phase 230V AC input to three phase 380 V AC output, the output will be useful for operating the induction motor.