Characterization of mode I disbonding behaviour of carbon/epoxy composites bonded with two adhesion qualities

La mancanza di procedure standard per la verifica delle strutture in compositi, al contrario dei materiali metallici, porta all’esigenza di una continua ricerca nel settore, al fine di ottenere risultati significativi che culminino in una standardizzazione delle procedure. In tale contesto si colloca la ricerca svolta per la stesura del presente elaborato, condotta presso il laboratorio DASML del TU Delft, nei Paesi Bassi. Il materiale studiato è un prepreg (preimpregnated) costituito da fibre di carbonio (M30SC) e matrice epossidica (DT120) con la particolare configurazione [0°/90°/±45°/±45°/90°/0°]. L’adesivo utilizzato per l’incollaggio è di tipo epossidico (FM94K). Il materiale è stato assemblato in laboratorio in modo da ottenere i provini da testare, di tipo DCB, ENF e CCP. Due differenti qualità dello stesso materiale sono state ottenute, una buona ottenuta seguendo le istruzione del produttore, ed una povera ottenuta modificando il processo produttivo suggerito, che risulta in un incollaggio di qualità nettamente inferiore rispetto al primo tipo di materiale. Lo scopo era quello di studiare i comportamenti di entrambe le qualità sotto due diversi modi di carico, modo I o opening mode e modo II o shear mode, entrambi attraverso test quasi-statici e a fatica, così da ottenere risultati comparabili tra di essi che permettano in futuro di identificare se si dispone di un materiale di buona qualità prima di procedere con il progetto dell’intera struttura. L’approccio scelto per lo studio dello sviluppo della delaminazione è un adattamento della teoria della Meccanica della Frattura Lineare Elastica (LEFM)

Effects of Paramuricea clavata (Risso, 1826) (Anthozoa: Plexauridae) forests on settlement of benthic species: an experimental approach

Rationale: Coralligenous habitat is considered the second most important subtidal “hot spot” of species diversity in the Mediterranean Sea after the Posidonia oceanica meadows. It can be defined as a typical Mediterranean biogenic hard bottom, mainly produced by the accumulation of calcareous encrusting algae that, together with other builder organisms, form a multidimensional framework with a high micro-spatial variability. The development of this habitat depends on physical factors (i.e. light, hydrodynamism, nutrients, etc.), but also biologic interactions can play a relevant role in structuring the benthic assemblages. This great environmental heterogeneity allows several different assemblages to coexist in a reduced space. One of the most beautiful is that characterised by the Mediterranean gorgonian Paramuricea clavata (Risso, 1826) that can contribute to above 40% of total biomass of the community and brings significant structural complexity into the coralligenous habitat. In sites moderately exposed to waves and currents, P. clavata can form high-density populations (up to 60 colonies m-2) between 20 – 70 m in depth. Being a suspension feeder, where it forms dense populations, P. clavata plays a significant role in transferring energy from planktonic to benthic system. The effects of the branched colonies of P. clavata could be comparable to those of the forests on land. They can affect the micro scale hydrodynamism and light, promoting or inhibiting the growth of other species. Unfortunately, gorgonians are threatened by several anthropogenic disturbance factors (i.e. fishing, pollution, tourism) and by climatic anomalies, linked to the global changes, that are responsible of thermal stress, development of mucilage and enhanced pathogens activity, leading to mass mortality events in last decades. Till now, the possible effects of gorgonian forest loss are largely unknown. Our goal was to analyse the ecological role of these sea fan forests on the coralligenous benthic assemblages. Experimental setup and main results: The influence of P. clavata in the settlement and recruitment of epibenthic organisms was analysed by a field experiment carried out in two randomly selected places: Tavolara island and Portofino promontory. The experiment consisted in recreate the presence and absence of the gorgonian forest on recruitment panels, arranged in four plots per type (forested and non-forested), interspersed each other, and deployed at the same depth. On every forested panel 3 gorgonian colonies about 20 cm height were grafted with the use of Eppendorf tubes and epoxy resin bicomponent simulating a density of 190 sea fans per m-2. This density corresponds to a mean biomass of 825 g DW m-2,3 which is of the same order of magnitude of the natural high-density populations. After about 4 months, the panels were collected and analysed in laboratory in order to estimate the percent cover of all the species that have colonized the substrata. The gorgonian forest effects were tested by multivariate and univariate permutational analyses of the variance (PERMANOVA). Recruited assemblages largely differed between the two study sites, probably due to different environmental conditions including water quality and turbidity. On overall, the presence of P. clavata reduced the settlement and recruitment of several algae: the shadow caused by the gorgonian might reduce light availability and therefore their growth. This effect might be greater in places where the waters are on average more clear, since at Portofino it is less visible and could be masked by the high turbidity of the water. The same pattern was registered for forams, more abundant outside gorgonian forest, probably linked with algal distribution, shadowing effect or alimentary competition. The last one hypothesis could be valid also for serpulids polychaetes that growth mainly on non-forested panels. An opposite trend, was showed by a species of bryozoan and by an hydroid that is facilitated by the presence of P. clavata, probably because it attenuates irradiance level and hydrodynamism. Species diversity was significantly reduced by the presence of P. clavata forests at both sites. This seems in contrast with what we expected, but the result may be influenced by the large algal component on non-forested panels. The analysis confirmed the presence of differences in the species diversity among plots and between sites respectively due to natural high variability of the coralligenous system and to different local environment conditions. The reduction of species diversity due to the presence of gorgonians appeared related to a worst evenness rather than to less species richness. With our experiment it is demonstrated that the presence of P. clavata forests can significantly alter local coralligenous assemblages patterns, promoting or inhibiting the recruitment of some species, modifying trophic relationships and adding heterogeneity and complexity to the habitat. Moreover, P. clavata could have a stabilising effect on the coralligenous assemblages.

Experimental analysis of fiber reinforced cementitious matrix (FRCM) confined masonry columns

The increasing use of Fiber Reinforced methods for strengthening existing brick masonry walls and columns, especially for the rehabilitation of historical buildings, has generated considerable research interest in understanding the failure mechanism in such systems. This dissertation is aimed to provide a basic understanding of the behavior of solid brick masonry walls unwrapped and wrapped with Fiber Reinforced Cementitious Matrix Composites. This is a new type of composite material, commonly known as FRCM, featuring a cementitious inorganic matrix (binder) instead of the more common epoxy one. The influence of the FRCM-reinforcement on the load-carrying capacity and strain distribution during compression test will be investigated using a full-field optical technique known as Digital Image Correlation. Compression test were carried on 6 clay bricks columns and on 7 clay brick walls in three different configuration, casted using bricks scaled respect the first one with a ratio 1:2, in order to determinate the effects of FRCM reinforcement. The goal of the experimental program is to understand how the behavior of brick masonry will be improved by the FRCM-wrapping. The results indicate that there is an arching action zone represented in the form of a parabola with a varying shape according to the used configuration. The area under the parabolas is considered as ineffectively confined. The effectively confined area is assumed to occur within the region where the arching action had been fully developed.

Valutazione analitica delle aree di delaminazione in materiali compositi avanzati soggetti ad impatti a bassa velocità

In questo lavoro di tesi è stato elaborato un modello analitico al fine di ottenere una stima dell’ampiezza di delaminazione a seguito di impatti a bassa velocità in laminati in composito, in particolare carbon/epoxy. Nel capitolo 2 è descritto il comportamento meccanico di tali laminati (equazioni costitutive della singola lamina, dell’intero laminato e costanti ingegneristiche dell’intero laminato per qualsiasi sistema di riferimento). Nel capitolo 3 viene descritta la filosofia di progettazione damage tolerance per tali materiali sottoposti a low-velocity impact (LVI) e richiamato il concetto di structural health monitoring. In particolare vengono descritti i tipi di difetti per un laminato in composito, vengono classificati gli impatti trasversali e si rivolge particolare attenzione agli impatti a bassa velocità. Nel paragrafo 3.4 sono invece elencate diverse tecniche di ispezione, distruttive e non, con particolare attenzione alla loro applicazione ai laminati in composito. Nel capitolo 4 è riportato lo stato dell’arte per la stima e la predizione dei danni dovuti a LVI nei laminati: vengono mostrate alcune tecniche che permettono di stimare accuratamente l’inizio del danno, la profondità dell’indentazione, la rottura delle fibre di rinforzo e la forza massima di impatto. L’estensione della delaminazione invece, è difficile da stimare a causa dei numerosi fattori che influenzano la risposta agli impatti: spesso vengono utilizzati, per tale stima, modelli numerici piuttosto dispendiosi in termini di tempo e di calcolo computazionale. Nel capitolo 5 viene quindi mostrata una prima formula analitica per il calcolo della delaminazione, risultata però inaffidabile perché tiene conto di un numero decisamente ristretto di fattori che influenzano il comportamento agli LVI. Nel capitolo 6 è mostrato un secondo metodo analitico in grado di calcolare l’ampiezza di delaminazione mediante un continuo aggiornamento della deflessione del laminato. Dal confronto con numerose prove sperimentali, sembra che il modello fornisca risultati vicini al comportamento reale. Il modello è inoltre fortemente sensibile al valore della G_IIc relativa alla resina, alle dimensioni del laminato e alle condizioni di vincolo. É invece poco sensibile alle variazioni delle costanti ingegneristiche e alla sequenza delle lamine che costituiscono il laminato. La differenza tra i risultati sperimentali e i risultati del modello analitico è influenzata da molteplici fattori, tra cui il più significativo sembra essere il valore della rigidezza flessionale, assunto costante dal modello.

Sintesi e caratterizzazione di prepolimeri per resine epossidiche derivanti da fonti rinnovabili e naturali attraverso un processo a basso impatto ambientale

La sostituzione di materie prime provenienti da risorse fossili con biomasse rinnovabili, utilizzando un processo a basso impatto ambientale, è una delle più importanti sfide della "Green Chemistry". Allo stesso tempo, la sintesi di resine epossidiche fornisce la chiave per la realizzazione di materiali ad alto valore aggiunto. Tuttavia, ad oggi, il 90% della produzione di resine epossidiche è basato sull'uso di bisfenolo A, che ha effetti di xenoestrogeno, ed epicloridrina, tossica e cancerogena. Su queste basi, è stata individuata una strategia sintetica per la sintesi di prepolimeri innovativi per resine epossidiche, che utilizza come substrato di reazione diidrossibenzeni di origine naturale ed evita l'uso di epicloridrina e altri reagenti tossici o pericolosi. La suddetta strategia sintetica è basata sulla sequenza: allilazione dei diidrossibenzeni - epossidazione dei doppi legami ottenuti. In questa procedura non vengono utilizzati drastiche condizioni di reazione e il solvente è acqua, con una catalisi di trasferimento di fase o, in aggiunte di acetonitrile, in un sistema bifasico. La resa complessiva dei due “step” dipende dalla posizione dei due ossidrili nei diidrossibenzeni. Il reagente che porta la resa massima è l’idrochinone (1,4 diidrossibenzene), che, come riportato in letteratura, permette la formazione di resine epossidiche con proprietà simili alle resine di epicloridrina e bisfenolo A. The substitution of raw materials from fossil fuels with renewable biomass using a low environmental impact process is one of the greatest challenges of the "Green Chemistry". At the same time, the synthesis of epoxy resins provides the key to the realization of high added value materials. However, 90% of the production of epoxy resins is based on the use of bisphenol A, a xenoestrogen, and epichlorohydrin, that is toxic and carcinogenic. On these bases, a synthetic strategy for the synthesis of innovative prepolymers of epoxy resins, that uses dihydroxybenzenes of natural origin as reaction substrates and avoids the use of epichlorohydrin and other toxic or dangerous reagents has been identified. The above synthetic strategy is based on the sequence: allylation of dihydroxybenzenes - epoxidation of the double bonds obtained. In this procedure, drastic reaction conditions are dismissed and the solvent used is water with a phase transfer catalysis or, in addition, acetonitrile in a biphasic system. The overall yield of the two steps depends on the position of the two hydroxyls of the dihydroxybenzenes. The reagent that leads to the highest yield is hydroquinone (1,4 dihydroxybenzene), which, as reported in literature, allows the formation of epoxy resins with similar properties to the resins from bisphenol A and epichlorohydrin.

A new method for continuous quality control of nsm cfrp systems

In the last decade the near-surface mounted (NSM) strengthening technique using carbon fibre reinforced polymers (CFRP) has been increasingly used to improve the load carrying capacity of concrete members. Compared to externally bonded reinforcement (EBR), the NSM system presents considerable advantages. This technique consists in the insertion of carbon fibre reinforced polymer laminate strips into pre-cut slits opened in the concrete cover of the elements to be strengthened. CFRP reinforcement is bonded to concrete with an appropriate groove filler, typically epoxy adhesive or cement grout. Up to now, research efforts have been mainly focused on several structural aspects, such as: bond behaviour, flexural and/or shear strengthening effectiveness, and energy dissipation capacity of beam-column joints. In such research works, as well as in field applications, the most widespread adhesives that are used to bond reinforcements to concrete are epoxy resins. It is largely accepted that the performance of the whole application of NSM systems strongly depends on the mechanical properties of the epoxy resins, for which proper curing conditions must be assured. Therefore, the existence of non-destructive methods that allow monitoring the curing process of epoxy resins in the NSM CFRP system is desirable, in view of obtaining continuous information that can provide indication in regard to the effectiveness of curing and the expectable bond behaviour of CFRP/adhesive/concrete systems. The experimental research was developed at the Laboratory of the Structural Division of the Civil Engineering Department of the University of Minho in Guimar\~aes, Portugal (LEST). The main objective was to develop and propose a new method for continuous quality control of the curing of epoxy resins applied in NSM CFRP strengthening systems. This objective is pursued through the adaptation of an existing technique, termed EMM-ARM (Elasticity Modulus Monitoring through Ambient Response Method) that has been developed for monitoring the early stiffness evolution of cement-based materials. The experimental program was composed of two parts: (i) direct pull-out tests on concrete specimens strengthened with NSM CFRP laminate strips were conducted to assess the evolution of bond behaviour between CFRP and concrete since early ages; and, (ii) EMM-ARM tests were carried out for monitoring the progressive stiffness development of the structural adhesive used in CFRP applications. In order to verify the capability of the proposed method for evaluating the elastic modulus of the epoxy, static E-Modulus was determined through tension tests. The results of the two series of tests were then combined and compared to evaluate the possibility of implementation of a new method for the continuous monitoring and quality control of NSM CFRP applications.

Preparazione di una resina epossidica bio-based e studio delle relative proprietà

Epoxy resins are very diffused materials due to their high added value deriving from high mechanical proprieties and thermal resistance; for this reason they are widely used both as metallic coatings in aerospace and in food packaging. However, their preparation uses dangerous reagents like bisphenol A and epichlorohydrin respectively classified as suspected of causing damage to fertility and to be carcinogen. Therefore, to satisfy the ever-growing attention to environmental problems and human safeness, we are considering alternative “green” processes through the use of reagents obtained as by-products from other processes and mild experimental conditions, and also economically sustainable and attractive for industries. Following previous results, we carried out the reaction leading to the formation of diphenolic acid (DPA), its allylation and the following epoxidation of the double bonds, all in aqueous solvent. In a second step the obtained product were cross-linked at high temperature with and without the use of hardeners. Then, on the obtained resin, some tests were performed like release in aqueous solution, scratch test and DSC analysis.

Experimental characterization of carbon-fiber-reinforced polymer laminates

The goal of this thesis is to make static tensile test on four Carbon Fiber Reinforced Polymer laminates, in such a way as to obtain the ultimate tensile strength of these laminates; in particular, the laminates analyzed were produced by Hand Lay-up technology. Testing these laminates we have a reference point on which to compare other laminates and in particular CFRP laminate produced by RTM technology.

Dynamic mechanical-thermal, microstructural and mechanical analysis of ultra-light polymer-metal composites: influence of forming

A really particular and innovative metal-polymer sandwich material is Hybrix. Hybrix is a product developed and manufactured by Lamera AB, Gothenburg, Sweden. This innovative hybrid material is composed by two relatively thin metal layers if compared to the core thickness. The most used metals are aluminum and stainless steel and are separated by a core of nylon fibres oriented perpendicularly to the metal plates. The core is then completed by adhesive layers applied at the PA66-metal interface that once cured maintain the nylon fibres in position. This special material is very light and formable. Moreover Hybrix, depending on the specific metal which is used, can achieve a good corrosion resistance and it can be cut and punched easily. Hybrix architecture itself provides extremely good bending stiffness, damping properties, insulation capability, etc., which again, of course, change in magnitude depending in the metal alloy which is used, its thickness and core thickness. For these reasons nowadays it shows potential for all the applications which have the above mentioned characteristic as a requirement. Finally Hybrix can be processed with tools used in regular metal sheet industry and can be handled as solid metal sheets. In this master thesis project, pre-formed parts of Hybrix were studied and characterized. Previous work on Hybrix was focused on analyze its market potential and different adhesive to be used in the core. All the tests were carried out on flat unformed specimens. However, in order to have a complete description of this material also the effect of the forming process must be taken into account. Thus the main activities of the present master thesis are the following: Dynamic Mechanical-Thermal Analysis (DMTA) on unformed Hybrix samples of different thickness and on pre-strained Hybrix samples, pure epoxy adhesive samples analysis and finally moisture effects evaluation on Hybrix composite structure.

Preparation and characterization of grafted nonwoven membranes for bioseparations

Protein purification plays a crucial role in biotechnology and biomanufacturing, where downstream unit operations account for 40%-80% of the overall costs. To overcome this issue, companies strive to simplify the separation process by reducing the number of steps and replacing expensive separation devices. In this context, commercially available polybutylene terephthalate (PBT) melt-blown nonwoven membranes have been developed as a novel disposable membrane chromatography support. The PBT nonwoven membrane is able to capture products and reduce contaminants by ion exchange chromatography. The PBT nonwoven membrane was modified by grafting a poly(glycidyl methacrylate) (GMA) layer by either photo-induced graft polymerization or heat induced graft polymerization. The epoxy groups of GMA monomer were subsequently converted into cation and anion exchangers by reaction with either sulfonic acid groups or diethylamine (DEA), respectively. Several parameters of the procedure were studied, especially the effect of (i) % weight gain and (ii) ligand density on the static protein binding capacity. Bovine Serum Albumin (BSA) and human Immunoglobulin G (hIgG) were utilized as model proteins in the anion and cation exchange studies. The performance of ion exchange PBT nonwovens by HIG was evaluated under flow conditions. The anion- and cation- exchange HIG PBT nonwovens were evaluated for their ability to selectively adsorb and elute BSA or hIgG from a mixture of proteins. Cation exchange nonwovens were not able to reach a good protein separation, whereas anion exchange HIG nonwovens were able to absorb and elute BSA with very high value of purity and yield, in only one step of purification.