Centrifuge Modeling of Sandy Slopes

Slope failure occurs in many areas throughout the world and it becomes an important problem when it interferes with human activity, in which disasters provoke loss of life and property damage. In this research we investigate the slope failure through the centrifuge modeling, where a reduced-scale model, N times smaller than the full-scale (prototype), is used whereas the acceleration is increased by N times (compared with the gravity acceleration) to preserve the stress and the strain behavior. The aims of this research “Centrifuge modeling of sandy slopes” are in extreme synthesis: 1) test the reliability of the centrifuge modeling as a tool to investigate the behavior of a sandy slope failure; 2) understand how the failure mechanism is affected by changing the slope angle and obtain useful information for the design. In order to achieve this scope we arranged the work as follows: Chapter one: centrifuge modeling of slope failure. In this chapter we provide a general view about the context in which we are working on. Basically we explain what is a slope failure, how it happens and which are the tools available to investigate this phenomenon. Afterwards we introduce the technology used to study this topic, that is the geotechnical centrifuge. Chapter two: testing apparatus. In the first section of this chapter we describe all the procedures and facilities used to perform a test in the centrifuge. Then we explain the characteristics of the soil (Nevada sand), like the dry unit weight, water content, relative density, and its strength parameters (c,φ), which have been calculated in laboratory through the triaxial test. Chapter three: centrifuge tests. In this part of the document are presented all the results from the tests done in centrifuge. When we talk about results we refer to the acceleration at failure for each model tested and its failure surface. In our case study we tested models with the same soil and geometric characteristics but different angles. The angles tested in this research were: 60°, 75° and 90°. Chapter four: slope stability analysis. We introduce the features and the concept of the software: ReSSA (2.0). This software allows us to calculate the theoretical failure surfaces of the prototypes. Then we show in this section the comparisons between the experimental failure surfaces of the prototype, traced in the laboratory, and the one calculated by the software. Chapter five: conclusion. The conclusion of the research presents the results obtained in relation to the two main aims, mentioned above.

Diversity of microbial communities at shallow-hydrothermal vents off Dominica, Lesser Antilles

Hydrothermal vents are often compared to desert oases, because of the presence of highly diverse and abundant biotic communities inhabiting these extreme environments. Nevertheless, the microbial communities associated with shallow-hydrothermal systems have been poorly studied. Hydrothermal activity at Dominica Island is quite well known under the geological and geochemical aspects, but no previous information existed about the microbial communities associated to this area. This thesis is therefore targeting the microbiology of hydrothermal sediments combining geochemical and molecular biological investigations, focusing on differences between hydrothermal vents and background (i.e. control) areas, and between hydrothermal sites. It was also intended to assess relationship between geochemical parameters and microbial diversity at the two hydrothermally impacted sites. Two shallow-sea hydrothermal vents located south-west off Dominica Island (Lesser Antilles) have been investigated in this study: Champagne Hot Springs and Soufriere Bay offshore vent. During this study, sediments for geochemical and molecular analyses were collected every 2 cm from the two impacted areas and from two control sites not associated with hydrothermal activity; in situ temperatures measurements were also taken every 5 cm deep in the sediment for all the sites. A geochemical characterization of the sediment porewater was performed through the analysis of several elements’ concentrations (i.e. H2S, Cl-, Br-, SO42-, Fe2+, Na+, K+, B+, Si+). Microbial communities at the different sites were studied by Automated Intergenic Spacer Analysis (ARISA). Inspection of the operational taxonomic units (OTUs) distribution was performed, as well as statistical analyses for communities’ structure and composition differences, and for changes of β-diversity along with sediment geochemistry. Data suggested that mixing between hydrothermal fluids and seawater results in distinct different environmental gradients and potential ecological niches between the two investigated hydrothermal vents, reflecting a difference in microbial community structures between them.