Response of Microcystis aeruginosa PCC 7806 to different CO2 concentrations

Future climatic change scenarios predict rising of the atmospheric CO2 levels which could favor the proliferation of some harmful bloom-forming cyanobacteria as Microcystis aeruginosa. In the present study, the response of M. aeruginosa strain PCC 7806 to two different partial pressure of CO2 was tested. Sandrini et al. (2013) recently found that several, but not all, M. aeruginosa strains lack the SbtA or BicA HCO3- uptake system genes; the contribution of different Ci transporters to photosynthesis and the difference between low and high affinity activated Ci uptake state were investigated. M. aeruginosa PCC 7806 was cultured in four chemostats containing modified BG11 medium with 10 mM NaNO3 and no presence of NaCl, NaHCO3, Na2CO3 and additional buffers. A wide variety of analysis on samples collected from continuous cultures – such as A750, medium composition, cellular composition, cell counting, mini-PAM, measurements with the O2 optode, Aminco, 77K fluorescence emission spectra – was carried out. Data analysis results showed that the increased CO2 concentration has a big effect on M. aeruginosa PCC 7806. Experiments were performed using the Oxy-4 O2 optode apparatus in order to measure the photosynthetic O2 evolution of samples taken from both batch and chemostat cultures. At low bicarbonate concentration, an evident inhibition of Na+-dependent HCO3- transporter BicA by LiCl at 25 mM was observed. The consequent addition of 25 mM NaCl was able to counteract the Li+ effect at pH 8.0 but not at pH 10.0. In the latter case, only the addition of a higher amount of HCO3- led to photosynthetic O2 evolution suggesting the important role of the BicA transporter. However, further studies are needed to better explain the results obtained as high pH levels might have an influence on the transport systems, altering the mechanism of pH regulation and the functioning of Na+/H+ antiporter systems.

A new method for continuous quality control of nsm cfrp systems

In the last decade the near-surface mounted (NSM) strengthening technique using carbon fibre reinforced polymers (CFRP) has been increasingly used to improve the load carrying capacity of concrete members. Compared to externally bonded reinforcement (EBR), the NSM system presents considerable advantages. This technique consists in the insertion of carbon fibre reinforced polymer laminate strips into pre-cut slits opened in the concrete cover of the elements to be strengthened. CFRP reinforcement is bonded to concrete with an appropriate groove filler, typically epoxy adhesive or cement grout. Up to now, research efforts have been mainly focused on several structural aspects, such as: bond behaviour, flexural and/or shear strengthening effectiveness, and energy dissipation capacity of beam-column joints. In such research works, as well as in field applications, the most widespread adhesives that are used to bond reinforcements to concrete are epoxy resins. It is largely accepted that the performance of the whole application of NSM systems strongly depends on the mechanical properties of the epoxy resins, for which proper curing conditions must be assured. Therefore, the existence of non-destructive methods that allow monitoring the curing process of epoxy resins in the NSM CFRP system is desirable, in view of obtaining continuous information that can provide indication in regard to the effectiveness of curing and the expectable bond behaviour of CFRP/adhesive/concrete systems. The experimental research was developed at the Laboratory of the Structural Division of the Civil Engineering Department of the University of Minho in Guimar\~aes, Portugal (LEST). The main objective was to develop and propose a new method for continuous quality control of the curing of epoxy resins applied in NSM CFRP strengthening systems. This objective is pursued through the adaptation of an existing technique, termed EMM-ARM (Elasticity Modulus Monitoring through Ambient Response Method) that has been developed for monitoring the early stiffness evolution of cement-based materials. The experimental program was composed of two parts: (i) direct pull-out tests on concrete specimens strengthened with NSM CFRP laminate strips were conducted to assess the evolution of bond behaviour between CFRP and concrete since early ages; and, (ii) EMM-ARM tests were carried out for monitoring the progressive stiffness development of the structural adhesive used in CFRP applications. In order to verify the capability of the proposed method for evaluating the elastic modulus of the epoxy, static E-Modulus was determined through tension tests. The results of the two series of tests were then combined and compared to evaluate the possibility of implementation of a new method for the continuous monitoring and quality control of NSM CFRP applications.

Proposal of a Continuous Read-out Implementation in the ALICE-TOF detector

The main purpose of ultrarelativistic heavy-ion collisions is the investigation of the QGP. The ALICE experiment situated at the CERN has been specifically designed to study heavy-ion collisions for centre-of-mass energies up to 5.5 per nucleon pair. Extended particle identification capability is one of the main characteristics of the ALICE experiment. In the intermediate momentum region (up to 2.5 GeV/c for pi/K and 4 GeV/c for K/p), charged particles are identified in the ALICE experiment by the Time of Flight (TOF) detector. The ALICE-TOF system is a large-area detector based on the use of Multi-gap Resistive Plate Chamber (MRPC) built with high efficiency, fast response and intrinsic time resolution better than 40 ps. This thesis work, developed with the ALICE-TOF Bologna group, is part of the efforts carried out to adapt the read-out of the detector to the new requirements after the LHC Long Shutdown 2. Tests on the feasibility of a new read-out scheme for the TOF detector have been performed. In fact, the achievement of a continuous read-out also for the TOF detector would not be affordable if one considers the replacement of the TRM cards both for hardware and budget reasons. Actually, the read-out of the TOF is limited at 250 kHz i.e. it would be able to collect up to just a fourth of the maximum collision rate potentially achievable for pp interactions. In this Master’s degree thesis work, I discuss a different read-out system for the ALICE-TOF detector that allows to register all the hits at the interaction rate of 1 MHz foreseen for pp interactions after the 2020, by using the electronics currently available. Such solution would allow the ALICE-TOF detector to collect all the hits generated by pp collisions at 1 MHz interaction rate, which corresponds to an amount four times larger than that initially expected at such frequencies with the triggered read-out system operated at 250 kHz for LHC Run 3. The obtained results confirm that the proposed read-out scheme is a viable option for the ALICE TOF detector. The results also highlighted that it will be advantageous if the ALICE-TOF group also implement an online monitoring system of noisy channels to allow their deactivation in real time.