Environmental impact assessment of the School of Engineering and Architecture (Lazzaretto) - A pathway towards LEED certification

The current work has for object the improvement and the maintenance of the School of Engineering and Architecture in Via Terracini 28 (Bologna), with the prospective to maximize the operative efficiency reducing to the minimum the environmental impact and the costs. In order to realize this work the LEED certification has been used. LEED (Leadership in Energy and Environmental Design) is a certification system of the buildings. It was born in United States by the U.S. Green Building Council (USGBC)

Recycling of end of life concrete fines (0 - 4 mm) into silica and cement

The purpose of this work is to find a methodology in order to make possible the recycling of fines (0 - 4 mm) in the Construction and Demolition Waste (CDW) process. At the moment this fraction is a not desired by-product: it has high contaminant content, it has to be separated from the coarse fraction, because of its high water absorption which can affect the properties of the concrete. In fact, in some countries the use of fines recycled aggregates is highly restricted or even banned. This work is placed inside the European project C2CA (from Concrete to Cement and Clean Aggregates) and it has been held in the Faculty of Civil Engineering and Geosciences of the Technical University of Delft, in particular, in the laboratory of Resources And Recycling. This research proposes some procedures in order to close the loop of the entire recycling process. After the classification done by ADR (Advanced Dry Recovery) the two fractions "airknife" and "rotor" (that together constitute the fraction 0 - 4 mm) are inserted in a new machine that works at high temperatures. The temperatures analysed in this research are 600 °C and 750 °C, cause at that temperature it is supposed that the cement bounds become very weak. The final goal is "to clean" the coarse fraction (0,250 - 4 mm) from the cement still attached to the sand and try to concentrate the cement paste in the fraction 0 - 0,250 mm. This new set-up is able to dry the material in very few seconds, divide it into two fractions (the coarse one and the fine one) thanks to the air and increase the amount of fines (0 - 0,250 mm) promoting the attrition between the particles through a vibration device. The coarse fraction is then processed in a ball mill in order to improve the result and reach the final goal. Thanks to the high temperature it is possible to markedly reduce the milling time. The sand 0 - 2 mm, after being heated and milled is used to replace 100% of norm sand in mortar production. The results are very promising: the mortar made with recycled sand reaches an early strength, in fact the increment with respect to the mortar made with norm sand is 20% after three days and 7% after seven days. With this research it has been demonstrated that once the temperature is increased it is possible to obtain a clean coarse fraction (0,250 - 4 mm), free from cement paste that is concentrated in the fine fraction 0 - 0,250 mm. The milling time and the drying time can be largely reduced. The recycled sand shows better performance in terms of mechanical properties with respect to the natural one.

Design methods and geometric modelling of scaffolds for bone tissue engineering

Every year, thousand of surgical treatments are performed in order to fix up or completely substitute, where possible, organs or tissues affected by degenerative diseases. Patients with these kind of illnesses stay long times waiting for a donor that could replace, in a short time, the damaged organ or the tissue. The lack of biological alternates, related to conventional surgical treatments as autografts, allografts, e xenografts, led the researchers belonging to different areas to collaborate to find out innovative solutions. This research brought to a new discipline able to merge molecular biology, biomaterial, engineering, biomechanics and, recently, design and architecture knowledges. This discipline is named Tissue Engineering (TE) and it represents a step forward towards the substitutive or regenerative medicine. One of the major challenge of the TE is to design and develop, using a biomimetic approach, an artificial 3D anatomy scaffold, suitable for cells adhesion that are able to proliferate and differentiate themselves as consequence of the biological and biophysical stimulus offered by the specific tissue to be replaced. Nowadays, powerful instruments allow to perform analysis day by day more accurateand defined on patients that need more precise diagnosis and treatments.Starting from patient specific information provided by TC (Computed Tomography) microCT and MRI(Magnetic Resonance Imaging), an image-based approach can be performed in order to reconstruct the site to be replaced. With the aid of the recent Additive Manufacturing techniques that allow to print tridimensional objects with sub millimetric precision, it is now possible to practice an almost complete control of the parametrical characteristics of the scaffold: this is the way to achieve a correct cellular regeneration. In this work, we focalize the attention on a branch of TE known as Bone TE, whose the bone is main subject. Bone TE combines osteoconductive and morphological aspects of the scaffold, whose main properties are pore diameter, structure porosity and interconnectivity. The realization of the ideal values of these parameters represents the main goal of this work: here we'll a create simple and interactive biomimetic design process based on 3D CAD modeling and generative algorithmsthat provide a way to control the main properties and to create a structure morphologically similar to the cancellous bone. Two different typologies of scaffold will be compared: the first is based on Triply Periodic MinimalSurface (T.P.M.S.) whose basic crystalline geometries are nowadays used for Bone TE scaffolding; the second is based on using Voronoi's diagrams and they are more often used in the design of decorations and jewellery for their capacity to decompose and tasselate a volumetric space using an heterogeneous spatial distribution (often frequent in nature). In this work, we will show how to manipulate the main properties (pore diameter, structure porosity and interconnectivity) of the design TE oriented scaffolding using the implementation of generative algorithms: "bringing back the nature to the nature".

Computational design of a new type of sandwich cross-section for a defined solution of a tree-like column produced by wire-and-arc additive manufacturing

When it comes to designing a structure, architects and engineers want to join forces in order to create and build the most beautiful and efficient building. From finding new shapes and forms to optimizing the stability and the resistance, there is a constant link to be made between both professions. In architecture, there has always been a particular interest in creating new shapes and types of a structure inspired by many different fields, one of them being nature itself. In engineering, the selection of optimum has always dictated the way of thinking and designing structures. This mindset led through studies to the current best practices in construction. However, both disciplines were limited by the traditional manufacturing constraints at a certain point. Over the last decades, much progress was made from a technological point of view, allowing to go beyond today's manufacturing constraints. With the emergence of Wire-and-Arc Additive Manufacturing (WAAM) combined with Algorithmic-Aided Design (AAD), architects and engineers are offered new opportunities to merge architectural beauty and structural efficiency. Both technologies allow for exploring and building unusual and complex structural shapes in addition to a reduction of costs and environmental impacts. Through this study, the author wants to make use of previously mentioned technologies and assess their potential, first to design an aesthetically appreciated tree-like column with the idea of secondly proposing a new type of standardized and optimized sandwich cross-section to the construction industry. Parametric algorithms to model the dendriform column and the new sandwich cross-section are developed and presented in detail. A catalog draft of the latter and methods to establish it are then proposed and discussed. Finally, the buckling behavior of this latter is assessed considering standard steel and WAAM material properties.

Heave of large excavations in clay: modelling and analysis of two british case-histories

ABSTRACT Il presente lavoro vuole introdurre la problematica del rigonfiamento del terreno a seguito di grandi scavi in argilla. Il sollevamento del terreno dopo lo scavo può passare inosservato ma sono numerosi i casi in cui il rigonfiamento dura per molti anni e addirittura decenni, Shell Centre, London, Lion Yard, Cambridge, Bell Common, London, ecc. Questo rigonfiamento il più delle volte è impedito dalla presenza di fondazioni, si genera quindi una pressione distribuita che se non considerata in fase di progetto può portare alla fessurazione della fondazione stessa. L’anima del progetto è la modellazione e l’analisi del rigonfiamento di grandi scavi in argilla, confrontando poi i risultati con i dati reali disponibili in letteratura. L’idea del progetto nasce dalla difficoltà di ottenere stime e previsioni attendibili del rigonfiamento a seguito di grandi scavi in argilla sovraconsolidata. Inizialmente ho esaminato la teoria e i fattori che influenzano il grado e la velocità del rigonfiamento, quali la rigidezza, permeabilità, fessurazione, struttura del suolo, etc. In seguito ho affrontato lo studio del comportamento rigonfiante di argille sovraconsolidate a seguito di scarico tensionale (scavi), si è evidenziata l’importanza di differenziare il rigonfiamento primario e il rigonfiamento secondario dovuto al fenomeno del creep. Il tema centrale del progetto è l’analisi numerica tramite Flac di due grandi scavi in argilla, Lion Yard, Cambridge, e, Bell Common, London. Attraverso una dettagliata analisi parametrica sono riuscito a trovare i migliori parametri che modellano il comportamento reale nei due casi in esame, in questo modo è possibile arrivare a stime e previsioni attendibili del fenomeno rigonfiante del terreno a seguito di grandi scavi. Gli scavi modellati Lion Yard e Bell Common sono rispettivamente in Gault Clay e London Clay, grazie a famosi recenti articoli scientifici sono riuscito a evidenziare la principali propietà che diversificano i due terreni in esame, tali propietà sono estremamente differenti dalle normali caratteristiche considerate per la progettazione in presenza di terreno argilloso; sono così riuscito a implementare i migliori parametri per descrivere il comportamento dei due terreni nei diversi modelli. Ho inoltre studiato l’interazione terreno-struttura, la pressione esercitata dal rigonfiamento del terreno è strettamente funzione delle caratteristiche di connesione tra fondazione superficiale e muro di sostegno, tale pressione non deve essere ignorata in fase progettuale poichè può raggiungere importanti valori. Nello scavo di Lion Yard, considerando la presenza delle fondazioni profonde ho evidenziato il fatto che il rigonfiamento crea una forza distribuita di taglio tra i pali di fondazione ed il terreno, anche tale sollecitazione dovrebbe essere considerata ai fini della progettazione. La problematica non si ferma solo sull’interazione terreno-fondazioni, infatti durante gli scavi di importanti fondazioni londinesi lo scarico tensionale ha creato uno spostamento significativo positivo verso la superfice di tratti di tunnel della metropolita, questo fenomeno può creare seri problemi di sicurezza nella rete dei trasporti pubblici. Infine sono stati messi a confronto i risultati del programma Flac con quelli di metodi semplificati, ho trovato che utilizzando il metodo iterativo di O’Brien i risultati sono simili alla realtà e il tempo di calcolo è molto inferiore di quello richiesto utilizzando Flac, 2-3 giorni. In conclusione posso affermare che grazie ad una dettagliata analisi parametrica è stato possibile stimare il rigonfiamento del terreno, argilla sovraconsolidata, nei due casi analizzati.

Transportation theory and planning

The aim of this research is to analyze the transport system and its subcomponents in order to highlight which are the design tools for physical and/or organizational projects related to transport supply systems. A characteristic of the transport systems is that the change of their structures can recoil on several entities, groups of entities, which constitute the community. The construction of a new infrastructure can modify both the transport service characteristic for all the user of the entire network; for example, the construction of a transportation infrastructure can change not only the transport service characteristics for the users of the entire network in which it is part of, but also it produces economical, social, and environmental effects. Therefore, the interventions or the improvements choices must be performed using a rational decision making approach. This approach requires that these choices are taken through the quantitative evaluation of the different effects caused by the different intervention plans. This approach becomes even more necessary when the decisions are taken in behalf of the community. Then, in order to understand how to develop a planning process in Transportation I will firstly analyze the transport system and the mathematical models used to describe it: these models provide us significant indicators which can be used to evaluate the effects of possible interventions. In conclusion, I will move on the topics related to the transport planning, analyzing the planning process, and the variables that have to be considered to perform a feasibility analysis or to compare different alternatives. In conclusion I will perform a preliminary analysis of a new transit system which is planned to be developed in New York City.

Steel and macro-synthetic self-compacting fibre reinforced concrete, experimental study on the long-term deformations

Experimental study on the long-term deformations of the fibre reinforced concrete. Steel and macro-synthetic fibers were used to evaluate the shrinkage, creep, mid-span deflection, cracking and rupture analysis of three different types of samples. At the end the main topics of ACI guidelines were analyzed in order to perform an overview of design.

Seismic mitigation of existing masonry structures by means of added damping and stiffness

In this work seismic upgrading of existing masonry structures by means of hysteretic ADAS dampers is treated. ADAS are installed on external concrete walls, which are built parallel to the building, and then linked to the building's slab by means of steel rod connection system. In order to assess the effectiveness of the intervention, a parametric study considering variation of damper main features has been conducted. To this aim, the concepts of equivalent linear system (ELS) or equivalent viscous damping are deepen. Simplified equivalent linear model results are then checked respect results of the yielding structures. Two alternative displacement based methods for damper design are herein proposed. Both methods have been validated through non linear time history analyses with spectrum compatible accelerograms. Finally ADAS arrangement for the non conventional implementation is proposed.