The contribution of the Finite Volume Point Dilution Method to the determination of solute mass flux in an alluvial aquifer.

Groundwater represents one of the most important resources of the world and it is essential to prevent its pollution and to consider remediation intervention in case of contamination. According to the scientific community the characterization and the management of the contaminated sites have to be performed in terms of contaminant fluxes and considering their spatial and temporal evolution. One of the most suitable approach to determine the spatial distribution of pollutant and to quantify contaminant fluxes in groundwater is using control panels. The determination of contaminant mass flux, requires measurement of contaminant concentration in the moving phase (water) and velocity/flux of the groundwater. In this Master Thesis a new solute flux mass measurement approach, based on an integrated control panel type methodology combined with the Finite Volume Point Dilution Method (FVPDM), for the monitoring of transient groundwater fluxes, is proposed. Moreover a new adsorption passive sampler, which allow to capture the variation of solute concentration with time, is designed. The present work contributes to the development of this approach on three key points. First, the ability of the FVPDM to monitor transient groundwater fluxes was verified during a step drawdown test at the experimental site of Hermalle Sous Argentau (Belgium). The results showed that this method can be used, with optimal results, to follow transient groundwater fluxes. Moreover, it resulted that performing FVPDM, in several piezometers, during a pumping test allows to determine the different flow rates and flow regimes that can occurs in the various parts of an aquifer. The second field test aiming to determine the representativity of a control panel for measuring mass flus in groundwater underlined that wrong evaluations of Darcy fluxes and discharge surfaces can determine an incorrect estimation of mass fluxes and that this technique has to be used with precaution. Thus, a detailed geological and hydrogeological characterization must be conducted, before applying this technique. Finally, the third outcome of this work concerned laboratory experiments. The test conducted on several type of adsorption material (Oasis HLB cartridge, TDS-ORGANOSORB 10 and TDS-ORGANOSORB 10-AA), in order to determine the optimum medium to dimension the passive sampler, highlighted the necessity to find a material with a reversible adsorption tendency to completely satisfy the request of the new passive sampling technique.

User centered retrofit: The case of kadk campus, Copenhagen, (dk)

The following research thesis is about a retrofit project made in Denmark, Copenhagen, and carried out on one of the buildings belonging to the Royal Danish Academy. The key assumption and base of the entire research process is that, up to now, the standard procedure in retrofit cases like this provides as comparative method between de facto and design, the use of Energy Simulation software. These programs generally divide the space into different thermal zones, assigning to each of them different levels of employment, activities, set-point temperatures set for cooling and heating analysis and so on, but always providing average and constant values, usually taken in the middle point of the single thermal zone. Therefore, the project and its research path stems from the attempt to investigate the potentialities of this kind of designing for retrofit process, as previously anticipated not antithetical but complementary to that classic energy-based retrofit, thus passing from the building scale, and all its thermal zones, to the users' scale, related to humans and microclimates. The main software used in this process is Autodesk Simulation CFD. The idea behind the project is that in certain situations, for example, it will not be necessary to add throughout insulation layers (previously parameterized and optimized with Design Builder), and that even in Winter conditions, due maybe to the users' activities, the increased level of clothing (clo) and the heat produced by equipments, thermal comfort could be achieved also in areas characterized by considerably lower MRT. After the analysis of the State of Art and its simulations, the project has still been supported by the tool itself, the CFD Software, in an iterative process aimed at achieving visible improvements in terms of MRT, on spaces with different needs and characteristics, both in Winter and Summer regimes.

Study of the calibration method of pressure-velocity probes and its application in a field of progressive plane waves

This dissertation presents a calibration procedure for a pressure velocity probe. The dissertation is divided into four main chapters. The first chapter is divided into six main sections. In the firsts two, the wave equation in fluids and the velocity of sound in gases are calculated, the third section contains a general solution of the wave equation in the case of plane acoustic waves. Section four and five report the definition of the acoustic impedance and admittance, and the practical units the sound level is measured with, i.e. the decibel scale. Finally, the last section of the chapter is about the theory linked to the frequency analysis of a sound wave and includes the analysis of sound in bands and the discrete Fourier analysis, with the definition of some important functions. The second chapter describes different reference field calibration procedures that are used to calibrate the P-V probes, between them the progressive plane wave method, which is that has been used in this work. Finally, the last section of the chapter contains a description of the working principles of the two transducers that have been used, with a focus on the velocity one. The third chapter of the dissertation is devoted to the explanation of the calibration set up and the instruments used for the data acquisition and analysis. Since software routines were extremely important, this chapter includes a dedicated section on them and the proprietary routines most used are thoroughly explained. Finally, there is the description of the work that has been done, which is identified with three different phases, where the data acquired and the results obtained are presented. All the graphs and data reported were obtained through the Matlab® routine. As for the last chapter, it briefly presents all the work that has been done as well as an excursus on a new probe and on the way the procedure implemented in this dissertation could be applied in the case of a general field.

Prosperity Thinking in Action: a case study from Future Food Institute’s Paideia Campus

The need for sustainable economic growth and environmental stewardship emerged around the start of the twentieth century when society became aware that the traditional development model would lead to the collapse of the terrestrial ecosystem in the long run. Over the years, the international community's environmental efforts have demonstrated unequivocally that the planet's limits are real. And so, the new development approach has laid the groundwork for the future. According to this model, design also plays a key role in ensuring a better future. The design has undergone an ecological and sustainable evolution as a result of the global environmental crisis and the degradation of our ecosystem and biodiversity. In this contest, Prosperity Thinking is inserted, a still evolving methodology developed by the Future Food Institute starting from 2019. The main concepts on which it is based are described, as well as the method that identifies it, which is divided into the following stages: 1) Problem Framing 2) Ideation and Prototyping 3) Test & Analyze. The development of the prosperity thinking toolkit is described, beginning with the search for tools from the literature on sustainable design and ending with its validation with the help of design experts. The testing of some tools will be recounted during a workshop organized by FFI, in which 15 people ranging in age from 14 to 40 will participate, and then the final version of the toolkit will be presented which has been obtained by adding to it the tools proposed by the experts. Finally, a reflection on the future of Prosperity Thinking, a method in constant evolution that must continue to follow societal and environmental changes in order to respond to the ever-increasingly complex challenge of sustainability.