Measurement and simulation of conducted disturbances on DC power grids of a HVDC system with an active DC/DC converter

With the increasing of the distributed generation, DC microgrids have become more and more common in the electrical network. To connect devices in a microgrid, converter are necessary, but they are also source of disturbances due to their functioning. In this thesis, measurement and simulation of conducted emissions, within the frequency range 2-150kHz, of a DC/DC buck converter are studied.

Towards NIR emission: 2-(1H-tetrazol-1-yl)pyridine as versatile ligand for the synthesis of two new families of cationic and neutral Ir(III) complexes.

In the last decades, cyclometalated Ir(III) complexes have drawn a large interest for their unique properties: they are excellent triplet state emitters, thus the emission is phosphorescent in nature; typically high quantum yields and good stability make them good candidates for luminescent materials. Moreover, through an opportune choice of the ligands, it is possible to tune the emission along the whole visible spectra. Thanks to these interesting features, Ir(III) complexes have found different applications in several areas of applied science, from OLEDs to bioimaging. In particular, regarding the second application, a remarkable red-shift in the emission is required, in order to minimize the problem of the tissue penetration and the possible damages for the organisms. With the aim of synthesizing a new family of NIR emitting Ir(III) complexes, we envisaged the possibility to use for the first time 2-(1H-tetrazol-1-yl)pyridine as bidentate ligand able to provide the required red-shift of the emission of the final complexes. Exploiting the versatility of the ligand, I prepared two different families of heteroleptic Ir(III) complexes. In detail, in the first case the 2-(1H-tetrazol-1-yl)pyridine was used as bis-chelating N^N ligand, leading to cationic complexes, while in the second case it was used as cyclometalating C^N ligand, giving neutral complexes. The structures of the prepared molecules have been characterised by NMR spectroscopy and mass spectrometry. Moreover, the neutral complexes’ emissive properties have been measured: emission spectra have been recorded in solution at both room temperature and 77K, as well as in PMMA matrix. DFT calculation has then been performed and the obtained results have been compared to experimental ones.

WEC-Sim Application for the Assessment of Wave Energy Generation in the Tyrrhenian Sea and the North Sea Through the 2-Body Point Absorber (2BPA) and the Oscillating Surge Wave Energy Converter (OSWEC)

In recent years, developed countries have turned their attention to clean and renewable energy, such as wind energy and wave energy that can be converted to electrical power. Companies and academic groups worldwide are investigating several wave energy ideas today. Accordingly, this thesis studies the numerical simulation of the dynamic response of the wave energy converters (WECs) subjected to the ocean waves. This study considers a two-body point absorber (2BPA) and an oscillating surge wave energy converter (OSWEC). The first aim is to mesh the bodies of the earlier mentioned WECs to calculate their hydrostatic properties using axiMesh.m and Mesh.m functions provided by NEMOH. The second aim is to calculate the first-order hydrodynamic coefficients of the WECs using the NEMOH BEM solver and to study the ability of this method to eliminate irregular frequencies. The third is to generate a *.h5 file for 2BPA and OSWEC devices, in which all the hydrodynamic data are included. The BEMIO, a pre-and post-processing tool developed by WEC-Sim, is used in this study to create *.h5 files. The primary and final goal is to run the wave energy converter Simulator (WEC-Sim) to simulate the dynamic responses of WECs studied in this thesis and estimate their power performance at different sites located in the Mediterranean Sea and the North Sea. The hydrodynamic data obtained by the NEMOH BEM solver for the 2BPA and OSWEC devices studied in this thesis is imported to WEC-Sim using BEMIO. Lastly, the power matrices and annual energy production (AEP) of WECs are estimated for different sites located in the Sea of Sicily, Sea of Sardinia, Adriatic Sea, Tyrrhenian Sea, and the North Sea. To this end, the NEMOH and WEC-Sim are still the most practical tools to estimate the power generation of WECs numerically.

Design e simulazione di un convertitore DC-DC per applicazioni automotive implementato mediante tecnologia GaN

L’obiettivo dell’elaborato è quello di presentare una soluzione di collegamento ed interfacciamento tra il supercondensatore (SC) dell’HESS (sistema ibrido di accumulo dell’energia situato all’interno di un veicolo elettrico) e il DC-link (bus che fornisce la potenza necessaria all’inverter che pilota il motore elettrico) attraverso un convertitore DC-DC ad alta efficienza che utilizzi tecnologie di potenza al nitruro di gallio (GaN). Il convertitore presentato è un convertitore DC-DC bidirezionale in configurazione Half-Bridge, esso dovrà funzionare in modalità Boost, ogni qualvolta il motore richieda energia extra dal SC, in modalità Buck per ricaricare il SC durante la frenata rigenerativa. In seguito ad un’introduzione ai veicoli elettrici, alla loro architettura e al perché il SC è così fondamentale, verrà presentata una breve introduzione ai convertitori di potenza (Capitolo 1). Si passerà poi alla presentazione delle tecnologie GaN mostrando come esse rappresentino il futuro dell’elettronica di potenza grazie ai loro numerosi vantaggi (Capitolo 2). Nel capitolo 3 si entrerà nel vivo della progettazione, è qui che sarà progettata ed implementata la soluzione proposta. Verrà effettuata una prima simulazione del circuito, tenendo conto degli effetti parassiti dei soli componenti, attraverso l’ausilio del software LTSpice. Il Capitolo 4 prevede una breve introduzione alle tecniche di layout, utili nella costruzione del circuito stampato presentata all’interno del medesimo capitolo. Il PCB sarà modellato mediante un secondo software denominato KiCAD. Infine, nel Capitolo 5, si procederà con la simulazione elettromagnetica del circuito stampato, essa permetterà di individuare gli effetti parassiti dovuti alle non idealità del layout e di mostrare l’effettiva differenza di efficienza tra un caso semi-ideale e un caso semi-reale.

Modeling and Design of Phase Shifted Full Bridge Isolated DC-DC ZVS Converter with Peak Current Mode Control

Nowadays, there is a boom in the use of electrification. Electric vehicles are gaining interest worldwide due to various factors, including climate and environmental awareness. In this thesis, a step-down isolated power supply for electric tractors is investigated, specifically the phase-shifted full-bridge (PSFB) DC-DC with synchronous rectification and zero-voltage switching (ZVS). This converter was selected for its high-power capacity with high efficiency. A 3500 W PSFB converter with peak current control (PCCM) is designed and modeled in MATLAB. The input voltage range is from 550 V to 820 V and the output voltage range is limited to 9 V to 16 V with a maximum output current of 250 A. All components were commercially designed and selected, including magnetics for the high-frequency transformer and inductors, taking into account loss calculations. Zero voltage switching for the lagging leg is achieved at 13% to 100% load. The proven efficiency of the converter is around 90