Shelf Life Assessment of Fresh Poultry Meat Packaged in Novel Bionanocomposite of Chitosan Incorporated with ZnO nanoparticles synthesized using food industry by-products

Nel settore alimentare viene utilizzata un’elevata quantità di materie plastiche per conservare i prodotti e facilitarne la distribuzione. L’utilizzo di questi polimeri ha un costo ambientale piuttosto elevato, per questo trovare surrogati ecosostenibili diventa sempre più importante. In questa tesi abbiamo testato l’efficacia del confezionamento di un prodotto altamente deperibile, quale carne di pollo, con un biofilm a base di chitosano. Il chitosano è polisaccaride largamente presente in natura, dotato di caratteristiche chimico-fisiche che permettono l’ottenimento di un film con proprietà meccaniche e di barriera simili ai polimeri tradizionali, oltre a possedere attività antibatterica. Abbiamo realizzato film contenenti chitosano e altri biocomposti, quali montmorillonite, nanoparticelle di ossido di zinco e olio essenziale di rosmarino, per un totale di 6 film con diversa composizione. Tramite analisi microbiologiche e chimico-fisiche abbiamo confrontato l’efficacia dei diversi film prodotti rispetto ad un controllo (carne conservata in un contenitore asettico). Le analisi sono state svolte in doppio, a 0, 3, 7, 10, 15 giorni di conservazione ad una temperatura di 4°C. In diversi film abbiamo ottenuto una riduzione significativa rispetto al controllo (p<0,05) della conta totale dei microrganismi mesofili aerobici (TMAM) e delle Enterobacteriaceae. La rilevazione del pH e dell’acidità titolabile ha fornito risultati in linea a quelli microbiologici. I campioni nel biofilm hanno spesso subito una variazione significativa (p<0,05) dell’umidità rispetto al controllo, a causa dell’elevata permeabilità al vapore acqueo. L’analisi dei TBARS non ha spesso riportato differenze significative rispetto al controllo (p>0,05), e quando presenti, è perché il campione era più ossidato del controllo (p<0,05). Invece, è stato ottenuto un miglioramento significativo (p<0,05) dello Hue angle tra i film e il controllo. I risultati ottenuti forniscono le basi per studi aggiuntivi.

Experimental evaluation of the z-resolution in different clinical Digital Breast Tomosynthesis systems using commercial phantoms

Digital Breast Tomosynthesis (DBT) is an advanced mammography technique based on the reconstruction of a pseudo-volumetric image. To date, image quality represents the most deficient section of DBT quality control protocols. In fact, related tests are not yet characterized by either action levels or typical values. This thesis work focuses on the evaluation of one aspect of image quality: the z-resolution. The latter is studied in terms of Artifact Spread Function (ASF), a function that describes the signal spread of a detail along the reconstructed focal planes. To quantify the ASF numerically, its Full Width at Half Maximum (FWHM) is calculated and used as a representative index of z-resolution. Experimental measurements were acquired in 24 DBT systems, of 7 different models, currently in use in 20 hospital facilities in Italy. The analysis, performed on the clinical reconstructed images, of 5 different commercial phantoms, lead to the identification of characteristic FWHM values for each type of DBT system. The ASF clearly showed a dependence on the size of the detail, providing higher FWHM values for larger objects. The z-resolution was found to be positively influenced by the acquisition angle: Fujifilm sistematically showed wider ASF profiles in ST mode (15°) than in HR mode (40°). However, no clear relationship was found between angular range and ASF, among different DBT systems, due to the influence of the peculiarities of each reconstruction algorithm. The experimental approach shown in this thesis work can be proposed as a z-resolution quality control test procedure. Contextually, the values found could be used as a starting point for identifying typical values to be included in the test, in a DBT protocol. Clearly, a statistically significant number of images is needed to do this. The equipment involved in this work is located in hospitals and is not available for research purposes, so only a limited amount of data was acquired and processed.

Characterization of a prototype for cone beam breast computed tomography

The project aims to experiment the Cone Beam Breast Computed Tomography technique using a standard digital mammography system. The work is focused on the definition of a protocol of quality measurements for the pre-clinical evaluation of the machine. The paper is developed in two parts. The first is specifically concerned with the methods used to define the image quality and dosimetry aspects specific for digital mammography devices. A complete characterization of the system has been performed according to the applicable IEC standards to assure the performances of the equipment and define the quality levels. Due to the lack of a quality control protocol dedicated to CBBCT mammography scanner, a new equivalent test procedure has been proposed. The second part of the paper is focused on the evaluation, through quantitative and visual analyzes, of the CBCT exam feasibility in the hardware and software conditions currently proposed by IMS Giotto. The prototype was in fact developed differing from the technical choices of competing companies and developed for a different intended use. The main difference with respect to the existing breast CT scanners is the possibility of performing on the same system the CBBCT scanning but also all the mammographic techniques. In this thesis, we aim to assess whether, in the current setup, considering a dosimetric range very close to that used in the clinic, the tests produce results that can be considered acceptable or at least indicative of the feasibility of the entire project from a commercial point of view. For this purpose, the final reconstruction images, obtained by two previously developed software, are analyzed.