Recycling of end of life concrete fines (0 - 4 mm) into silica and cement

The purpose of this work is to find a methodology in order to make possible the recycling of fines (0 - 4 mm) in the Construction and Demolition Waste (CDW) process. At the moment this fraction is a not desired by-product: it has high contaminant content, it has to be separated from the coarse fraction, because of its high water absorption which can affect the properties of the concrete. In fact, in some countries the use of fines recycled aggregates is highly restricted or even banned. This work is placed inside the European project C2CA (from Concrete to Cement and Clean Aggregates) and it has been held in the Faculty of Civil Engineering and Geosciences of the Technical University of Delft, in particular, in the laboratory of Resources And Recycling. This research proposes some procedures in order to close the loop of the entire recycling process. After the classification done by ADR (Advanced Dry Recovery) the two fractions "airknife" and "rotor" (that together constitute the fraction 0 - 4 mm) are inserted in a new machine that works at high temperatures. The temperatures analysed in this research are 600 °C and 750 °C, cause at that temperature it is supposed that the cement bounds become very weak. The final goal is "to clean" the coarse fraction (0,250 - 4 mm) from the cement still attached to the sand and try to concentrate the cement paste in the fraction 0 - 0,250 mm. This new set-up is able to dry the material in very few seconds, divide it into two fractions (the coarse one and the fine one) thanks to the air and increase the amount of fines (0 - 0,250 mm) promoting the attrition between the particles through a vibration device. The coarse fraction is then processed in a ball mill in order to improve the result and reach the final goal. Thanks to the high temperature it is possible to markedly reduce the milling time. The sand 0 - 2 mm, after being heated and milled is used to replace 100% of norm sand in mortar production. The results are very promising: the mortar made with recycled sand reaches an early strength, in fact the increment with respect to the mortar made with norm sand is 20% after three days and 7% after seven days. With this research it has been demonstrated that once the temperature is increased it is possible to obtain a clean coarse fraction (0,250 - 4 mm), free from cement paste that is concentrated in the fine fraction 0 - 0,250 mm. The milling time and the drying time can be largely reduced. The recycled sand shows better performance in terms of mechanical properties with respect to the natural one.

Lewis acid catalysed direct glycosylation of N-acetyl-D-glucosamine

Incorporation of the relevant monosaccharide N-Acetyl-D-glucosamine (GlcNAc) into synthetic oligosaccharides by chemical glycosylation is still a very challenging object of studies, since direct reactions are low yielding. This issue is generally ascribed to its low solubility in common solvents and to the formation of a poorly reactive oxazoline intermediate, which is typically bypassed by introducing extra synthetic steps to avoid the presence of the NHAc moiety during glycosylation. Recently, a new direct Lewis acids-catalysed GlcNAc-ylation protocol has been disclosed, with acylated donors appearing to hold potential for high yielding glycosylation reactions. This master project focused indeed on a novel synthesis of promising 1-acyl GlcNAc donors, in order to test them in direct Lewis acid catalysed glycosylation without the need of N-protecting groups. Screening of various Lewis acids and reaction conditions with these acylated donors has been carried out, in presence of reactive primary alcohols as well as more challenging carbohydrate acceptor alcohols. These experiments demonstrated that the fine tuning of the leaving group combined with a suitable metal triflate could lead to a successful reaction outcome in the direct glycosylation. Successful methodology of this kind would provide rapid access to naturally occurring N-glycan motifs, such as the highly relevant human milk oligosaccharides (HMOs).

Design of an innovative electric vehicle simulator for Charging Systems' End-of-Line Testing

The trend related to the turnover of internal combustion engine vehicles with EVs goes by the name of electrification. The push electrification experienced in the last decade is linked to the still ongoing evolution in power electronics technology for charging systems. This is the reason why an evolution in testing strategies and testing equipment is crucial too. The project this dissertation is based on concerns the investigation of a new EV simulator design. that optimizes the structure of the testing equipment used by the company who commissioned this work. Project requirements can be summarized in the following two points: space occupation reduction and parallel charging implementation. Some components were completely redesigned, and others were substituted with equivalent ones that could perform the same tasks. In this way it was possible to reduce the space occupation of the simulator, as well as to increase the efficiency of the testing device. Moreover, the possibility of conjugating different charging simulations could be investigated by parallelly launching two testing procedures on a unique machine, properly predisposed for supporting the two charging protocols used. On the back of the results achieved in the body of this dissertation, a new design for the EV simulator was proposed. In this way, space reduction was obtained, and space occupation efficiency was improved with the proposed new design. The testing device thus resulted to be way more compact, enabling to gain in safety and productivity, along with a 25% cost reduction. Furthermore, parallel charging was implemented in the proposed new design since the conducted tests clearly showed the feasibility of parallel charging sessions. The results presented in this work can thus be implemented to build the first prototype of the new EV simulator.

Smart Data Analysis on Lamborghini Connected Vehicles

The thesis is the result of work conducted during a period of six months at the Strategy department of Automobili Lamborghini S.p.A. in Sant'Agata Bolognese (BO) and concerns the study and analysis of Big Data relating to Lamborghini's connected cars. The Big Data is a project of Connected Car Project House, that is an inter-departmental team which works toward the definition of the Lamborghini corporate connectivity strategy and its implementation in the product portfolio. The Data of the connected cars is one of the hottest topics right now in the automotive industry; in fact, all the largest automotive companies are investi,ng a lot in this direction, in order to derive the greatest advantages both from a purely economic point of view, because from these data you can understand a lot the behaviors and habits of each driver, and from a technological point of view because it will increasingly promote the development of 5G that will be an important enabler for the future of connectivity. The main purpose of the work by Lamborghini prospective is to analyze the data of the connected cars, in particular a data-set referred to connected Huracans that had been already placed on the market, and, starting from that point, derive valuable Key Performance Indicators (KPIs) on which the company could partly base the decisions to be made in the near future. The key result that we have obtained at the end of this period was the creation of a Dashboard, in which is possible to visualize many parameters and indicators both related to driving habits and the use of the vehicle itself, which has brought great insights on the huge potential and value that is present behind the study of these data. The final Demo of the project has received great interest, not only from the whole strategy department but also from all the other business areas of Lamborghini, making mostly a great awareness that this will be the road to follow in the coming years.

Design and specification of a modular automatic testing solution

Electric vehicles and electronic components inside the vehicle are becoming increasingly important. The software as well starts to have a significant impact on modern high-end cars therefore a careful validation process needs to be implemented with the aim of having a bug free product when it is released. The software complexity increases and thus also the testing phases is more demanding. Test can be troublesome and, in some cases, boring and easy. The intelligence can be moved in test definition and writing rather than on test execution. The aim of this document is to start the definition of an automatic modular testing system capable to execute test cycles on systems that interacts with the CAN networks and with DUT that can be touched with a robotic arm. The document defines a first version of the system, in particular the hardware interface part with the aim of taking logs and execute test in an automated fashion with the test engineer can have a higher focus on the test definition and analysis rather than execution.