Neural Network Based UAV Fault Tolerant Control with Aerodynamic Disturbance Estimation and Compensation

In this thesis, the problem of controlling a quadrotor UAV is considered. It is done by presenting an original control system, designed as a combination of Neural Networks and Disturbance Observer, using a composite learning approach for a system of the second order, which is a novel methodology in literature. After a brief introduction about the quadrotors, the concepts needed to understand the controller are presented, such as the main notions of advanced control, the basic structure and design of a Neural Network, the modeling of a quadrotor and its dynamics. The full simulator, developed on the MATLAB Simulink environment, used throughout the whole thesis, is also shown. For the guidance and control purposes, a Sliding Mode Controller, used as a reference, it is firstly introduced, and its theory and implementation on the simulator are illustrated. Finally the original controller is introduced, through its novel formulation, and implementation on the model. The effectiveness and robustness of the two controllers are then proven by extensive simulations in all different conditions of external disturbance and faults.

Apprendimento hebbiano in robotica: teoria e applicazione

Partendo dallo sviluppo della teoria dell'apprendimento Hebbiano, si delinea un percorso per la creazione di robot in grado di apprendere tramite architettura DAC e Value System.

Eye-trauma: Event driven control software for gesture recognition in medical simulation

Il progetto Eye-Trauma si colloca all'interno dello sviluppo di un simulatore chirurgico per traumi alla zona oculare, sviluppato in collaborazione con Simulation Group in Boston, Harvard Medical School e Massachusetts General Hospital. Il simulatore presenta un busto in silicone fornito di moduli intercambiabili della zona oculare, per simulare diversi tipi di trauma. L'utilizzatore è chiamato ad eseguire la procedura medica di saturazione tramite degli strumenti chirurgici su cui sono installati dei sensori di forza e di apertura. I dati collezionati vengono utilizzati all'interno del software per il riconoscimento dei gesti e il controllo real-time della performance. L'algoritmo di gesture recognition, da me sviluppato, si basa sul concetto di macchine a stati; la transizione tra gli stati avviene in base agli eventi rilevati dal simulatore.

Studio dell'influenza dell'Adaptive Cruise Control sul carico di lavoro e sulla condotta di guida degli utenti

Il presente elaborato intende valutare l’influenza che i sistemi di assistenza alla guida (ADAS) hanno sul comportamento dei conducenti, con particolare attenzione alla distrazione ed al workload (carico di lavoro fisico e mentale) che essi provocano. Lo studio si concentrerà in particolare sull’analisi del comportamento di guida dei conducenti a bordo di un veicolo dotato di Adaptive Cruise Control.

Analisi del tempo di reazione dei conducenti dei veicoli con metodologie innovative: l'influenza del sistema Adaptive Cruise Control

La presente tesi si pone l’obiettivo di studiare e comprendere l’influenza che i sistemi di assistenza alla guida (ADAS – Advanced Driver Assistance Systems), installati negli autoveicoli di nuova generazione, hanno sulla condotta di guida degli automobilisti, con particolare attenzione alla distrazione ed al workload che essi provocano. Punto centrale dell’analisi è il sistema Adaptive Cruise Control (ACC) che permette al guidatore del veicolo sia di mantenere una velocità di marcia costante sia di rilevare, tramite sensoristica, i veicoli che lo precedono, intervenendo sul sistema frenante e sulla centralina di controllo del motore, così da garantire il mantenimento della distanza di sicurezza selezionata. Lo studio, attraverso l’utilizzo di tecniche innovative, si sofferma, in particolare, sull’analisi del comportamento di guida dei conducenti a bordo di un veicolo dotato di Adaptive Cruise Control. Il fine della ricerca è quello di determinare se e quanto il sistema ACC influisca sul conducente in termini di carico di lavoro cognitivo e fisico e di livelli d’attenzione, concentrandosi sulla valutazione del tempo di reazione con sistema acceso o spento.

Modeling, simulation, and control of a formation of multirotor aircraft for cooperative transportation of suspended loads

The work presented in this thesis aims to contribute to innovation in the Urban Air Mobility and Delivery sector and represents a solid starting point for air logistics and its future scenarios. The dissertation focuses on modeling, simulation, and control of a formation of multirotor aircraft for cooperative load transportation, with particular attention to environmental sustainability. First, a simulation and test environment is developed to assess technologies for suspended load stabilization. Starting from the mathematical model of two identical multirotors, formation-flight-keeping and collision-avoidance algorithms are analyzed. This approach guarantees both the safety of the vehicles within the formation and that of the payload, which may be made of people in the very near future. Afterwards, a mathematical model for the suspended load is implemented, as well as an active controller for its stabilization. The key focus of this part is represented by both analysis and control of payload oscillatory motion, by thoroughly investigating load kinetic energy decay. At this point, several test cases were introduced, in order to understand which strategy is the most effective and safe in terms of future applications in the field of air logistics.

Simulation and Implementation of a PMSM Sensorless Control Algorithm for Submarine Applications

In this thesis, the study and the simulation of two advanced sensorless speed control techniques for a surface PMSM are presented. The aim is to implement a sensorless control algorithm for a submarine auxiliary propulsion system. This experimental activity is the result of a project collaboration with L3Harris Calzoni, a leader company in A&D systems for naval handling in military field. A Simulink model of the whole electric drive has been developed. Due to the satisfactory results of the simulations, the sensorless control system has been implemented in C code for STM32 environment. Finally, several tests on a real brushless machine have been carried out while the motor was connected to a mechanical load to simulate the real scenario of the final application. All the experimental results have been recorded through a graphical interface software developed at Calzoni.

Simulation of visible light communications in vehicular networks

The rapid development in the field of lighting and illumination allows low energy consumption and a rapid growth in the use, and development of solid-state sources. As the efficiency of these devices increases and their cost decreases there are predictions that they will become the dominant source for general illumination in the short term. The objective of this thesis is to study, through extensive simulations in realistic scenarios, the feasibility and exploitation of visible light communication (VLC) for vehicular ad hoc networks (VANETs) applications. A brief introduction will introduce the new scenario of smart cities in which visible light communication will become a fundamental enabling technology for the future communication systems. Specifically, this thesis focus on the acquisition of several, frequent, and small data packets from vehicles, exploited as sensors of the environment. The use of vehicles as sensors is a new paradigm to enable an efficient environment monitoring and an improved traffic management. In most cases, the sensed information must be collected at a remote control centre and one of the most challenging aspects is the uplink acquisition of data from vehicles. My thesis discusses the opportunity to take advantage of short range vehicle-to-vehicle (V2V) and vehicle-to-roadside (V2R) communications to offload the cellular networks. More specifically, it discusses the system design and assesses the obtainable cellular resource saving, by considering the impact of the percentage of vehicles equipped with short range communication devices, of the number of deployed road side units, and of the adopted routing protocol. When short range communications are concerned, WAVE/IEEE 802.11p is considered as standard for VANETs. Its use together with VLC will be considered in urban vehicular scenarios to let vehicles communicate without involving the cellular network. The study is conducted by simulation, considering both a simulation platform (SHINE, simulation platform for heterogeneous interworking networks) developed within the Wireless communication Laboratory (Wilab) of the University of Bologna and CNR, and network simulator (NS3). trying to realistically represent all the wireless network communication aspects. Specifically, simulation of vehicular system was performed and introduced in ns-3, creating a new module for the simulator. This module will help to study VLC applications in VANETs. Final observations would enhance and encourage potential research in the area and optimize performance of VLC systems applications in the future.

Real-time control of an Electrodynamic Shaker

Questa tesi è essenzialmente focalizzata sullo sviluppo di un sistema di controllo in tempo reale per uno Shaker Elettrodinamico usato per riprodurre profili di vibrazione ambientale registrati in contesti reali e di interesse per il recupero di energia. Grazie all'utilizzo di uno shaker elettrodinamico è quindi possibile riprodurre scenari di vibrazione reale in laboratorio e valutare più agevolmente le prestazioni dei trasduttori meccanici. Tuttavia, è richiesto un controllo dello Shaker non solo in termini di stabilità ma anche per garantire l'esatta riproduzione del segnale registrato nel contesto reale. In questa tesi, si è scelto di sviluppare un controllo adattivo nel dominio del tempo per garantire la corretta riproduzione del profilo di accelerazione desiderato. L'algoritmo è stato poi implementato sul sistema di prototipazione rapida dSPACE DS1104 basata su microprocessore PowerPC. La natura adattiva dell'algoritmo proposto permette di identificare cambiamenti nella risposta dinamica del sistema, e di regolare di conseguenza i parametri del controllore. Il controllo del sistema è stato ottenuto anteponendo al sistema un filtro adattivo la cui funzione di trasferimento viene continuamente adattata per rappresentare al meglio la funzione di trasferimento inversa del sistema da controllare. Esperimenti in laboratorio confermano l'efficacia del controllo nella riproduzione di segnali reali e in tipici test di sweep frequenziale.

Impact of irrigation in the Po valley (Italy) on meteorological parameters through numerical simulation

Recent studies found that soil-atmosphere coupling features, through soil moisture, have been crucial to simulate well heat waves amplitude, duration and intensity. Moreover, it was found that soil moisture depletion both in Winter and Spring anticipates strong heat waves during the Summer. Irrigation in geophysical studies can be intended as an anthropogenic forcing to the soil-moisture, besides changes in land proprieties. In this study, the irrigation was add to a LAM hydrostatic model (BOLAM) and coupled with the soil. The response of the model to irrigation perturbation is analyzed during a dry Summer season. To identify a dry Summer, with overall positive temperature anomalies, an extensive climatological characterization of 2015 was done. The method included a statistical validation on the reference period distribution used to calculate the anomalies. Drought conditions were observed during Summer 2015 and previous seasons, both on the analyzed region and the Alps. Moreover July was characterized as an extreme event for the referred distribution. The numerical simulation consisted on the summer season of 2015 and two run: a control run (CTR), with the soil coupling and a perturbed run (IPR). The perturbation consists on a mask of land use created from the Cropland FAO dataset, where an irrigation water flux of 3 mm/day was applied from 6 A.M. to 9 A.M. every day. The results show that differences between CTR and IPR has a strong daily cycle. The main modifications are on the air masses proprieties, not on to the dynamics. However, changes in the circulation at the boundaries of the Po Valley are observed, and a diagnostic spatial correlation of variable differences shows that soil moisture perturbation explains well the variation observed in the 2 meters height temperature and in the latent heat fluxes.On the other hand, does not explain the spatial shift up and downslope observed during different periods of the day. Given the results, irrigation process affects the atmospheric proprieties on a larger scale than the irrigation, therefore it is important in daily forecast, particularly during hot and dry periods.

A framework for cyber-physical system simulation

In these last years, systems engineering has became one of the major research domains. The complexity of systems has increased constantly and nowadays Cyber-Physical Systems (CPS) are a category of particular interest: these, are systems composed by a cyber part (computer-based algorithms) that monitor and control some physical processes. Their development and simulation are both complex due to the importance of the interaction between the cyber and the physical entities: there are a lot of models written in different languages that need to exchange information among each other. Normally people use an orchestrator that takes care of the simulation of the models and the exchange of informations. This orchestrator is developed manually and this is a tedious and long work. Our proposition is to achieve to generate the orchestrator automatically through the use of Co-Modeling, i.e. by modeling the coordination. Before achieving this ultimate goal, it is important to understand the mechanisms and de facto standards that could be used in a co-modeling framework. So, I studied the use of a technology employed for co-simulation in the industry: FMI. In order to better understand the FMI standard, I realized an automatic export, in the FMI format, of the models realized in an existing software for discrete modeling: TimeSquare. I also developed a simple physical model in the existing open source openmodelica tool. Later, I started to understand how works an orchestrator, developing a simple one: this will be useful in future to generate an orchestrator automatically.