Magnesium based nanoparticles for hydrogen storage

Questo lavoro riguarda la sintesi e caratterizzazione di nanoparticelle basate sul magnesio per l'immagazzinamento di idrogeno. Le nanoparticelle sono state cresciute mediante Inert Gas Condensation, una tecnica aerosol in cui il materiale viene sublimato e diretto verso i substrati tramite un flusso di gas inerte, e caratterizzate attraverso microscopia elettronica e diffrazione di raggi X. Queste operazioni sono state eseguite presso il Dipartimento di Fisica e Astronomia dell'Università di Bologna. Sono stati sintetizzati due tipi di particelle: nel primo il magnesio viene deposto direttamente sul substrato, nel secondo esso incontra un flusso di ossigeno prima di depositarsi sulla superficie. In questo modo si formano delle particelle con struttura core-shell in cui la parte interna è formata da magnesio e quella esterna dal suo ossido. La presenza di una shell consistente dovrebbe permettere, secondo il modello di deformazioni elastiche, di diminuire il valore assoluto dell'entropia di formazione dell'idruro di magnesio, condizione necessaria affinché il desorbimento di idrogeno possa avvenire in maniera più agevole rispetto a quanto non accada col materiale bulk. Tutti i campioni sono stati ricoperti di palladio, il quale favorisce la dissociazione della molecola di idrogeno. La capacità di assorbimento dell'idrogeno da parte dei campioni è stata studiata mediante idrogenografia, una tecnica ottica recentemente sviluppata in cui la quantità di gas assorbita dal materiale è legata alla variazione di trasmittanza ottica dello stesso. Le misure sono state eseguite presso l'Università Tecnica di Delft. I risultati ottenuti evidenziano che le nanoparticelle di solo magnesio mostrano dei chiari plateau di pressione corrispondenti all'assorbimento di idrogeno, tramite cui sono stati stimati i valori di entalpia di formazione. Al contrario, i campioni con struttura core-shell, la cui crescita rappresenta di per sé un risultato interessante, non presentano tale comportamento.

Determination of local density of states in amorphous oxide semiconductors with Kelvin Probe Force Microscopy

Amorphous semiconductors are important materials as they can be deposited by physical deposition techniques on large areas and even on plastic substrates. Therefore, they are crucial for transistors in large active matrices for imaging and transparent wearable electronics. The most widely applied candidate for amorphous thin film transistors production is Indium Gallium Zinc Oxide (IGZO). It is attracting much interest because of its optical transparency, facile processing by sputtering deposition and notable improved charge carrier mobility with respect to hydrogenated amorphous silicon a-Si:H. Degradation of the device and long-term performance issues have been observed if IGZO thin film transistors are subjected to electrical stress, leading to a modification of IGZO channel properties and subthreshold slope. Therefore, it is of great interest to have a reliable and precise method to study the conduction band tail, and the density of states in amorphous semiconductors. The aim of this thesis is to develop a local technique using Kelvin Probe Force Microscopy to study the evolution of IGZO DOS properties. The work is divided into three main parts. First, solutions to the non-linear Poisson-Boltzmann equation of a metal-insulator-semiconductor junction describing the charge accumulation and its relation to DOS properties are elaborated. Second macroscopic techniques such as capacitance voltage (CV) measurements and photocurrent spectroscopy are applied to obtain a non-local estimate of band-tail DOS properties in thin film transistor samples. The third part of my my thesis is dedicated to the KPFM measurements. By fitting the data to the developed numerical model, important parameters describing the amorphous conduction band tail are obtained. The results are in excellent agreement with the macroscopic characterizations. KPFM result is comparable also with non-local optoelectronic characterizations, such as photocurrent spectroscopy.

Fabrication by magnetron sputtering and characterization of electrodes based on CuIn0.7Ga0.3Se2 (CIGS)

This thesis work aims to produce and test multilayer electrodes for their use as photocathode in a PEC device. The electrode developed is based on CIGS, a I-III-VI2 semiconductor material composed of copper (Cu), indium (In), Gallium (Ga) and selenium (Se). It has a bandgap in the range of 1.0-2.4 eV and an absorption coefficient of about 105cm−1, which makes it a promising photocathode for PEC water splitting. The idea of our multilayer electrode is to deposit a thin layer of CdS on top of CIGS to form a solid-state p–n junction and lead to more efficient charge separation. In addition another thin layer of AZO (Aluminum doped zinc oxide) is deposit on top of CdS since it would form a better alignment between the AZO/CdS/CIGS interfaces, which would help to drive the charge transport further and minimize charge recombination. Finally, a TiO2 layer on top of the electrodes is used as protective layer during the H2 evolution. FTO (Fluorine doped tin oxide) and Molybdenum are used as back-contact. We used the technique of RF magnetron sputtering to deposit the thin layers of material. The structural characterization performed by XDR measurement confirm a polycrystalline chalcopyrite structural with a preferential orientation along the (112) direction for the CIGS. From linear fit of the Tauc plot, we get an energy gap of about 1.16 eV. In addition, from a four points measurements, we get a resistivity of 0.26 Ωcm. We performed an electrochemical characterization in cell of our electrodes. The results show that our samples have a good stability but produce a photocurrent of the order of μA, three orders of magnitude smaller than our targets. The EIS analysis confirm a significant depletion of the species in front of the electrode causing a lower conversion of the species and less current flows.