Cure Induced Residual Stresses on Thick Composite Components Manufactured by Additive Process

This study investigates the effect of an additive process in manufacturing of thick composites. Airstone 780 E epoxy resin and 785H Hardener system is used in the analysis since it is widely used wind turbine blade, namely thick components. As a fiber, fabric by SAERTEX (812 g/m2) with a 0-90 degrees layup direction is used. Temperature overshoot is a major issue during the manufacturing of thick composites. A high temperature overshoot leads to an increase in residual stresses. These residual stresses are causing warping, delamination, dimensional instability, and undesired distortion of composite structures. A coupled thermo-mechanical model capable of predicting cure induced residual stresses have been built using the commercial FE software Abaqus®. The possibility of building thick composite components by means of adding a finite number of sub-laminates has been investigated. The results have been compared against components manufactured following a standard route. The influence of pre-curing of the sub-laminates has also been addressed and results compared with standard practice. As a result of the study, it is found that introducing additive process can prevent temperature overshoot to occur and benefits the residual stresses generation during the curing process. However, the process time required increases by 50%, therefore increasing the manufacturing costs. An optimized cure cycle is required to minimize process time and cure induced defects simultaneously.

Effect of multiple sources of disturbance on rocky benthic assemblages in some localities of Salento, Apulia

The first part of my work consisted in samplings conduced in nine different localities of the salento peninsula and Apulia (Italy): Costa Merlata (BR), Punta Penne (BR), Santa Cesarea terme (LE), Santa Caterina (LE), Torre Inserraglio (LE), Torre Guaceto (BR), Porto Cesareo (LE), Otranto (LE), Isole Tremiti (FG). I collected data of species percentage covering from the infralittoral rocky zone, using squares of 50x50 cm. We considered 3 sites for location and 10 replicates for each site, which has been taken randomly. Then I took other data about the same places, collected in some years, and I combined them together, to do a spatial analysis. So I started from a data set of 1896 samples but I decided not to consider time as a factor because I have reason to think that in this period of time anthropogenic stressors and their effects (if present), didn’t change considerably. The response variable I’ve analysed is the covering percentage of an amount of 243 species (subsequently merged into 32 functional groups), including seaweeds, invertebrates, sediment and rock. 2 After the sampling, I have been spent a period of two months at the Hopkins Marine Station of Stanford University, in Monterey (California,USA), at Fiorenza Micheli's laboratory. I've been carried out statistical analysis on my data set, using the software PRIMER 6. My explorative analysis starts with a nMDS in PRIMER 6, considering the original data matrix without, for the moment, the effect of stressors. What comes out is a good separation between localities and it confirms the result of ANOSIM analysis conduced on the original data matrix. What is possible to ensure is that there is not a separation led by a geographic pattern, but there should be something else that leads the differences. Is clear the presence of at least three groups: one composed by Porto cesareo, Torre Guaceto and Isole tremiti (the only marine protected areas considered in this work); another one by Otranto, and the last one by the rest of little, impacted localities. Inside the localities that include MPA(Marine Protected Areas), is also possible to observe a sort of grouping between protected and controlled areas. What comes out from SIMPER analysis is that the most of the species involved in leading differences between populations are not rare species, like: Cystoseira spp., Mytilus sp. and ECR. Moreover I assigned discrete values (0,1,2) of each stressor to all the sites I considered, in relation to the intensity with which the anthropogenic factor affect the localities. 3 Then I tried to estabilish if there were some significant interactions between stressors: by using Spearman rank correlation and Spearman tables of significance, and taking into account 17 grades of freedom, the outcome shows some significant stressors interactions. Then I built a nMDS considering the stressors as response variable. The result was positive: localities are well separeted by stressors. Consequently I related the matrix with 'localities and species' with the 'localities and stressors' one. Stressors combination explains with a good significance level the variability inside my populations. I tried with all the possible data transformations (none, square root, fourth root, log (X+1), P/A), but the fourth root seemed to be the best one, with the highest level of significativity, meaning that also rare species can influence the result. The challenge will be to characterize better which kind of stressors (including also natural ones), act on the ecosystem; and give them a quantitative and more accurate values, trying to understand how they interact (in an additive or non-additive way).

Sintesi di nuovi derivati tri-componente per target photodynamic therapy della neoplasia prostatica

Therapies for the treatment of prostate cancer show several limitations, especially when the cancer metastasizes or acquires resistance to treatment. In addition, most of the therapies currently used entails the occurrence of serious side effects. A different therapeutic approach, more selective and less invasive with respect either to radio or to chemotherapy, is represented by the photodynamic therapy (PDT). The PDT is a treatment that makes use of photosensitive drugs: these agents are pharmacologically inactive until they are irradiated with light at an appropriate wavelength and in the presence of oxygen. The drug, activated by light, forms singlet oxygen, a highly reactive chemical species directly responsible for DNA damage, thus of cell death. In this thesis we present two synthetic strategies for the preparation of two new tri-component derivatives for photodynamic therapy of advanced prostate cancer, namely DRPDT1 and DRPDT2. Both derivatives are formed by three basic elements covalently bounded to each other: a specific ligand with high affinity for the androgen receptor, a suitably chosen spacer molecule and a photoactivated molecule. In particular, DRPDT2 differs from DRPDT1 from the nature of the AR ligand. In fact, in the case of DRPDT2 we used a synthetically engineered androgen receptor ligand able to photo-react even in the absence of oxygen, by delivering NO radical. The presence of this additional pharmacophore, together with the porphyrin, may ensure an additive/synergistic effect to the photo-stimulated therapy, which than may act both in the presence of oxygen and in hypoxic conditions. This approach represents the first example of multimodal photodynamic therapy for prostate cancer.