Skin tissue engineering: medical problems and technological solutions.

In questo elaborato si affrontano problematiche cliniche legate ai traumi gravi della cute in cui è necessario intervenire chirurgicamente per ripristinare una situazione normale: si approfondisce lo studio della fisiologia del tessuto, la classificazione dei gradi delle ustioni della pelle, la guarigione delle ferite e la meccanica della cute. Il trapianto di tessuto autologo costituisce la soluzione più efficace e con minori complicazioni. Tuttavia il paziente potrebbe non presentare una superficie di cute disponibile sufficientemente estesa, per cui si ricorre ad altri metodi. In primo luogo, si effettuano degli allotrapianti di tessuto di donatore cadavere prelevati secondo le normative vigenti e conservati attraverso le varie tecniche, il cui sviluppo ha consentito una durata di conservazione maggiore; mentre la glicerolizzazione abbatte al 100% il rischio di trasmissione di patologie e lo sviluppo di microorganismi, la crioconservazione preserva la vitalità del tessuto. La chirurgia utilizzata per queste operazioni si avvale di tecnologie innovative come la Tecnologia a Pressione Negativa. Un'alternativa necessaria per sopperire all'ingente richiesta di tessuto di donatore sono i sostituti cutanei, che presentano un grande potenziale per il futuro. Per eliminare totalmente il rischio di rigetto sarebbe necessario personalizzare il costrutto utilizzando cellule autologhe, ma la ricerca è stata rallentata da minori investimenti da parte dell'industria biomedica, che si è maggiormente focalizzata sulla realizzazione di prodotti utilizzabili da un più ampio raggio di pazienti. Per queste ragioni, l'ingegneria tissutale della cute ha trovato più ampio campo di applicazione nel sistema dei test in vitro. A tale scopo sono stati creati dei protocolli certificati per testare la corrosività, la irritabilità e la vitalità del tessuto cutaneo, quali EpiDerm, EpiSkin e SkinEthic che si avvalgono dell'uso del metodo MMT e della spettrofotometria, che è diventata un supporto fondamentale per le scienze biologiche.

Analysis and partial solutions of security problems in automotive environments

Questo scritto mira a fare una panoramica dei problemi legati alla sicurezza della comunicazione tra componenti interne dei veicoli e delle soluzioni oggigiorno disponibili. Partendo con una descrizione generale del circuito interno dell’auto analizzeremo i suoi punti di accesso e discuteremo i danni prodotti dalla sua manomissione illecita. In seguito vedremo se ´è possibile prevenire tali attacchi dando un’occhiata alle soluzioni disponibili e soffermandoci in particolare sui moduli crittografici e le loro applicazioni. Infine presenteremo l’implementazione pratica di un protocollo di autenticazione tra ECUs e una dimostrazione matematica della sua sicurezza.

The quest for unnecessary symbolism across the media - analysis and possible solutions

Lo scopo della presente ricerca è sottolineare la tendenza alla ossessiva e spesso superflua ricerca del simbolismo nell’analisi di opere, specificatamente testi letterari e film, e proporre una possibile soluzione per porre fine o almeno diminuire gli effetti del fenomeno. A partire da una definizione esaustiva della parola simbolo, l’analisi verterà sull’evoluzione del concetto di simbolismo attraverso i media, e il cambiamento intrinseco causato da tale evoluzione. In seguito, analizzerò un semisconosciuto ma emblematico sondaggio, condotto nel 1973 da Bruce McAllister, all’epoca studente, che interrogò acutamente numerosi autori riguardo al loro rapporto con il simbolismo, ponendo l’accento su alcune delle risposte da lui ricevute, che gettano una luce rivelatrice sul symbol hunting e symbol planting. Dopodiché scenderò ancor più nel dettaglio, esemplificando con due storie brevi: Signs and Symbols (Segni e Simboli), di Vladimir Nabokov e Big Two-hearted River (Grande fiume a due cuori) di Hernest Hemingway. Dopodiché, analizzerò il falso simbolismo come luogo cinematografico, ponendo l’accento sugli aspetti di planting e hunting, e mi avvarrò dell’aiuto di due film significativi sul tema realizzati in tempi recenti, ovvero Inception (2010) e Memento (2000), di Christopher Nolan, che possono essere interpretati come una meta-critica dell’abuso di simboli, e rappresentano una pietra miliare nell’analisi di symbol planting e symbol hunting. In conclusione, proporrò la mia personale possibile soluzione, ovvero il prendere le opere d’arte in qualunque forma, specialmente di fiction, “così come sono”, separandole e scindendole dalle proprie aspettative. È necessario prendere in considerazione un ritorno alla letteralità, per poter avvicinarsi maggiormente alla vera anima di una storia, di un libro, di un film, altrimenti esiste la possibilità che tutto ciò che guardiamo o vediamo sia per sempre irrimediabilmente contaminato dalla nostra dimensione privata.

Bioremediation of PAHs - Limitations and soultions

Introduction 1.1 Occurrence of polycyclic aromatic hydrocarbons (PAH) in the environment Worldwide industrial and agricultural developments have released a large number of natural and synthetic hazardous compounds into the environment due to careless waste disposal, illegal waste dumping and accidental spills. As a result, there are numerous sites in the world that require cleanup of soils and groundwater. Polycyclic aromatic hydrocarbons (PAHs) are one of the major groups of these contaminants (Da Silva et al., 2003). PAHs constitute a diverse class of organic compounds consisting of two or more aromatic rings with various structural configurations (Prabhu and Phale, 2003). Being a derivative of benzene, PAHs are thermodynamically stable. In addition, these chemicals tend to adhere to particle surfaces, such as soils, because of their low water solubility and strong hydrophobicity, and this results in greater persistence under natural conditions. This persistence coupled with their potential carcinogenicity makes PAHs problematic environmental contaminants (Cerniglia, 1992; Sutherland, 1992). PAHs are widely found in high concentrations at many industrial sites, particularly those associated with petroleum, gas production and wood preserving industries (Wilson and Jones, 1993). 1.2 Remediation technologies Conventional techniques used for the remediation of soil polluted with organic contaminants include excavation of the contaminated soil and disposal to a landfill or capping - containment - of the contaminated areas of a site. These methods have some drawbacks. The first method simply moves the contamination elsewhere and may create significant risks in the excavation, handling and transport of hazardous material. Additionally, it is very difficult and increasingly expensive to find new landfill sites for the final disposal of the material. The cap and containment method is only an interim solution since the contamination remains on site, requiring monitoring and maintenance of the isolation barriers long into the future, with all the associated costs and potential liability. A better approach than these traditional methods is to completely destroy the pollutants, if possible, or transform them into harmless substances. Some technologies that have been used are high-temperature incineration and various types of chemical decomposition (for example, base-catalyzed dechlorination, UV oxidation). However, these methods have significant disadvantages, principally their technological complexity, high cost , and the lack of public acceptance. Bioremediation, on the contrast, is a promising option for the complete removal and destruction of contaminants. 1.3 Bioremediation of PAH contaminated soil & groundwater Bioremediation is the use of living organisms, primarily microorganisms, to degrade or detoxify hazardous wastes into harmless substances such as carbon dioxide, water and cell biomass Most PAHs are biodegradable unter natural conditions (Da Silva et al., 2003; Meysami and Baheri, 2003) and bioremediation for cleanup of PAH wastes has been extensively studied at both laboratory and commercial levels- It has been implemented at a number of contaminated sites, including the cleanup of the Exxon Valdez oil spill in Prince William Sound, Alaska in 1989, the Mega Borg spill off the Texas coast in 1990 and the Burgan Oil Field, Kuwait in 1994 (Purwaningsih, 2002). Different strategies for PAH bioremediation, such as in situ , ex situ or on site bioremediation were developed in recent years. In situ bioremediation is a technique that is applied to soil and groundwater at the site without removing the contaminated soil or groundwater, based on the provision of optimum conditions for microbiological contaminant breakdown.. Ex situ bioremediation of PAHs, on the other hand, is a technique applied to soil and groundwater which has been removed from the site via excavation (soil) or pumping (water). Hazardous contaminants are converted in controlled bioreactors into harmless compounds in an efficient manner. 1.4 Bioavailability of PAH in the subsurface Frequently, PAH contamination in the environment is occurs as contaminants that are sorbed onto soilparticles rather than in phase (NAPL, non aqueous phase liquids). It is known that the biodegradation rate of most PAHs sorbed onto soil is far lower than rates measured in solution cultures of microorganisms with pure solid pollutants (Alexander and Scow, 1989; Hamaker, 1972). It is generally believed that only that fraction of PAHs dissolved in the solution can be metabolized by microorganisms in soil. The amount of contaminant that can be readily taken up and degraded by microorganisms is defined as bioavailability (Bosma et al., 1997; Maier, 2000). Two phenomena have been suggested to cause the low bioavailability of PAHs in soil (Danielsson, 2000). The first one is strong adsorption of the contaminants to the soil constituents which then leads to very slow release rates of contaminants to the aqueous phase. Sorption is often well correlated with soil organic matter content (Means, 1980) and significantly reduces biodegradation (Manilal and Alexander, 1991). The second phenomenon is slow mass transfer of pollutants, such as pore diffusion in the soil aggregates or diffusion in the organic matter in the soil. The complex set of these physical, chemical and biological processes is schematically illustrated in Figure 1. As shown in Figure 1, biodegradation processes are taking place in the soil solution while diffusion processes occur in the narrow pores in and between soil aggregates (Danielsson, 2000). Seemingly contradictory studies can be found in the literature that indicate the rate and final extent of metabolism may be either lower or higher for sorbed PAHs by soil than those for pure PAHs (Van Loosdrecht et al., 1990). These contrasting results demonstrate that the bioavailability of organic contaminants sorbed onto soil is far from being well understood. Besides bioavailability, there are several other factors influencing the rate and extent of biodegradation of PAHs in soil including microbial population characteristics, physical and chemical properties of PAHs and environmental factors (temperature, moisture, pH, degree of contamination). Figure 1: Schematic diagram showing possible rate-limiting processes during bioremediation of hydrophobic organic contaminants in a contaminated soil-water system (not to scale) (Danielsson, 2000). 1.5 Increasing the bioavailability of PAH in soil Attempts to improve the biodegradation of PAHs in soil by increasing their bioavailability include the use of surfactants , solvents or solubility enhancers.. However, introduction of synthetic surfactant may result in the addition of one more pollutant. (Wang and Brusseau, 1993).A study conducted by Mulder et al. showed that the introduction of hydropropyl-ß-cyclodextrin (HPCD), a well-known PAH solubility enhancer, significantly increased the solubilization of PAHs although it did not improve the biodegradation rate of PAHs (Mulder et al., 1998), indicating that further research is required in order to develop a feasible and efficient remediation method. Enhancing the extent of PAHs mass transfer from the soil phase to the liquid might prove an efficient and environmentally low-risk alternative way of addressing the problem of slow PAH biodegradation in soil.

Ultracold Bose-Fermi mixtures with pairing: quantum phase transition, mechanical stability, and trap confinement

Ultracold dilute gases occupy an important role in modern physics and they are employed to verify fundamental quantum theories in most branches of theoretical physics. The scope of this thesis work is the study of Bose-Fermi (BF) mixtures at zero temperature with a tunable pairing between bosons and fermions. The mixtures are treated with diagrammatic quantum many-body methods based on the so-called T-matrix formalism. Starting from the Fermi-polaron limit, I will explore various values of relative concentrations up to mixtures with a majority of bosons, a case barely considered in previous works. An unexpected quantum phase transition is found to occur in a certain range of BF coupling for mixture with a slight majority of bosons. The mechanical stability of mixtures has been analysed, when the boson-fermion interaction is changed from weak to strong values, in the light of experimental results recently obtained for a double-degenerate Bose-Fermi mixture of 23 Na - 40 K. A possible improvement in the description of the boson-boson repulsion based on Popov's theory is proposed. Finally, the effects of a harmonic trapping potential are described, with a comparison with the experimental data for the condensate fraction recently obtained for a trapped 23 Na - 40 K mixture.

Study and characterization of low molecular weight polymer solutions for application in lubricating oils

The aim of this thesis is to evaluate the possibility of using short linear polymer chains as additives in lubricating oil applications. Through previous works, it has been seen that they are particularly resistant to mechanical degradation, which is the main reason why lubricating oils need to be changed after a while. This is the main reason why they could be proposed as alternatives in the market. The results of this work have been split into two major phases: the first concentrated on characterizing a target product obtained through thermal degradation, starting from the original long chain parent polymer, and the second focused on the technological advancement of heat exchangers. Through the studies carried out, we’ve characterized our innovative polymers and the solutions made with them and base oil at different concentrations. The most promising result is that these short random coiled polymeric chains obey to a more general universal function which express the value of specific viscosity as function of a dimensionless quantity c/c*. For the design of the unit operation, several alternatives were proposed and these all shared the same final goal: cooling the polymer without the presence of oxygen to avoid oxidation and formation of unwanted substances. We’ve analyzed the main difficulties related to the presence of these highly viscous substances and, more importantly, how to deal with this situation (e.g. by considering radial static mixer or even more complex conformations).

Prediction and measurement of forced response of a composite blade undergoing nonlinear vibration

The main objective of this project is to experimentally demonstrate geometrical nonlinear phenomena due to large displacements during resonant vibration of composite materials and to explain the problem associated with fatigue prediction at resonant conditions. Three different composite blades to be tested were designed and manufactured, being their difference in the composite layup (i.e. unidirectional, cross-ply, and angle-ply layups). Manual envelope bagging technique is explained as applied to the actual manufacturing of the components; problems encountered and their solutions are detailed. Forced response tests of the first flexural, first torsional, and second flexural modes were performed by means of a uniquely contactless excitation system which induced vibration by using a pulsed airflow. Vibration intensity was acquired by means of Polytec LDV system. The first flexural mode is found to be completely linear irrespective of the vibration amplitude. The first torsional mode exhibits a general nonlinear softening behaviour which is interestingly coupled with a hardening behaviour for the unidirectional layup. The second flexural mode has a hardening nonlinear behaviour for either the unidirectional and angle-ply blade, whereas it is slightly softening for the cross-ply layup. By using the same equipment as that used for forced response analyses, free decay tests were performed at different airflow intensities. Discrete Fourier Trasform over the entire decay and Sliding DFT were computed so as to visualise the presence of nonlinear superharmonics in the decay signal and when they were damped out from the vibration over the decay time. Linear modes exhibit an exponential decay, while nonlinearities are associated with a dry-friction damping phenomenon which tends to increase with increasing amplitude. Damping ratio is derived from logarithmic decrement for the exponential branch of the decay.

Boundary condition identification of a bridge pier using experimental data and FEM modal updating

Over the past twenty years, new technologies have required an increasing use of mathematical models in order to understand better the structural behavior: finite element method is the one mostly used. However, the reliability of this method applied to different situations has to be tried each time. Since it is not possible to completely model the reality, different hypothesis must be done: these are the main problems of FE modeling. The following work deals with this problem and tries to figure out a way to identify some of the unknown main parameters of a structure. This main research focuses on a particular path of study and development, but the same concepts can be applied to other objects of research. The main purpose of this work is the identification of unknown boundary conditions of a bridge pier using the data acquired experimentally with field tests and a FEM modal updating process. This work doesn’t want to be new, neither innovative. A lot of work has been done during the past years on this main problem and many solutions have been shown and published. This thesis just want to rework some of the main aspects of the structural optimization process, using a real structure as fitting model.

Stress Concentration Factor and Fatigue Life Evaluation in offshore tubular KT-Joints

In the last few decades, offshore field has grown fast especially after the notable development of technologies, explorations of oil and gas in deep water and the high concern of offshore companies in renewable energy mainly Wind Energy. Fatigue damage was noticed as one of the main problems causing failure of offshore structures. The purpose of this research is to focus on the evaluation of Stress Concentration Factor and its influence on Fatigue Life for 2 tubular KT-Joints in offshore Jacket structure using different calculation methods. The work is done by using analytical calculations, mainly Efthymiou’s formulations, and numerical solutions, FEM analysis, using ABAQUS software. As for the analytical formulations, the calculations were done according to the geometrical parameters of each method using excel sheets. As for the numerical model, 2 different types of tubular KT-Joints are present where for each model 5 shell element type, 3 solid element type and 3 solid-with-weld element type models were built on ABAQUS. Meshing was assigned according to International Institute of Welding (IIW) recommendations, 5 types of mesh element, to evaluate the Hot-spot stresses. 23 different types of unitary loading conditions were assigned, 9 axial, 7 in-plane bending moment and 7 out-plane bending moment loads. The extraction of Hot-spot stresses and the evaluation of the Stress Concentration Factor were done using PYTHON scripting and MATLAB. Then, the fatigue damage evaluation for a critical KT tubular joint based on Simplified Fatigue Damage Rule and Local Approaches (Strain Damage Parameter and Stress Damage Parameter) methods were calculated according to the maximum Stress Concentration Factor conducted from DNV and FEA methods. In conclusion, this research helped us to compare different results of Stress Concentration Factor and Fatigue Life using different methods and provided us with a general overview about what to study next in the future.

Planning Processes for Transport Solutions An Application To the City of Bologna

Mathematical models and the involved methods applied to real contexts are essential tools for designing and evaluating solutions concerning physical elements and/or organizational components of transportation systems. To deal with this, the systems engineering approach is used, which considers the relationships among the transportation system elements and their performances. This approach allows quantifying the effects of transportation projects by taking into account the intrinsic complexity of the transportation system and then assessing the effects of solutions to solve – or mitigate – transportation problems. This thesis focuses on the application of the transport system engineering approach to a real city – Bologna, in northern Italy – in order to: 1. simulate the current transportation system conditions (status quo); 2. compare and assess the results obtained by two different approaches for simulating the link traffic flows on the road transportation network and their related impacts (externalities) 3. identify potential solutions to solve critical aspects, particularly in terms of traffic flow congestion and related environmental impacts (findings)