Performance comparison of C-V2X and WAVE protocols for vehicular to infrastructure communications: simulation of the highway use case

The objective of this thesis is the analysis and the study of the various access techniques for vehicular communications, in particular of the C-V2X and WAVE protocols. The simulator used to study the performance of the two protocols is called LTEV2Vsim and was developed by the CNI IEIIT for the study of V2V (Vehicle-to-Vehicle) communications. The changes I made allowed me to study the I2V (Infrastructure-to-Vehicle) scenario in highway areas and, with the results obtained, I made a comparison between the two protocols in the case of high vehicular density and low vehicular density, putting in relation to the PRR (packet reception ratio) and the cell size (RAW, awareness range). The final comparison allows to fully understand the possible performances of the two protocols and highlights the need for a protocol that allows to reach the minimum necessary requirements.

Simulation of visible light communications in vehicular networks

The rapid development in the field of lighting and illumination allows low energy consumption and a rapid growth in the use, and development of solid-state sources. As the efficiency of these devices increases and their cost decreases there are predictions that they will become the dominant source for general illumination in the short term. The objective of this thesis is to study, through extensive simulations in realistic scenarios, the feasibility and exploitation of visible light communication (VLC) for vehicular ad hoc networks (VANETs) applications. A brief introduction will introduce the new scenario of smart cities in which visible light communication will become a fundamental enabling technology for the future communication systems. Specifically, this thesis focus on the acquisition of several, frequent, and small data packets from vehicles, exploited as sensors of the environment. The use of vehicles as sensors is a new paradigm to enable an efficient environment monitoring and an improved traffic management. In most cases, the sensed information must be collected at a remote control centre and one of the most challenging aspects is the uplink acquisition of data from vehicles. My thesis discusses the opportunity to take advantage of short range vehicle-to-vehicle (V2V) and vehicle-to-roadside (V2R) communications to offload the cellular networks. More specifically, it discusses the system design and assesses the obtainable cellular resource saving, by considering the impact of the percentage of vehicles equipped with short range communication devices, of the number of deployed road side units, and of the adopted routing protocol. When short range communications are concerned, WAVE/IEEE 802.11p is considered as standard for VANETs. Its use together with VLC will be considered in urban vehicular scenarios to let vehicles communicate without involving the cellular network. The study is conducted by simulation, considering both a simulation platform (SHINE, simulation platform for heterogeneous interworking networks) developed within the Wireless communication Laboratory (Wilab) of the University of Bologna and CNR, and network simulator (NS3). trying to realistically represent all the wireless network communication aspects. Specifically, simulation of vehicular system was performed and introduced in ns-3, creating a new module for the simulator. This module will help to study VLC applications in VANETs. Final observations would enhance and encourage potential research in the area and optimize performance of VLC systems applications in the future.

Analysis on the implementation of V2X communications for PTWs

Inter-vehicular communications have been gaining momentum throughout the last years and they now occupy a prominent position among the objectives of car manufacturers. Motorcycle manufacturers want to keep pace with the 4 wheels world in order to make Powered Two-wheelers (PTW) integral part of the future connected mobility. The requirements for implementing inter-vehicular communication systems for motorcycles are the subjects of discussion in this thesis. The first purpose of this thesis is to introduce the reader to the world of vehicle-to-everything (V2X) communications, focusing on the Cooperative Intelligent Transport Systems (C-ITS) and the two main current technologies: ITS-G5, which is based on IEEE 802.11p, and cellular vehicle-to-everything (C-V2X). The evolution of these technologies will be also treated. Afterwards, the core of this work is presented: the analysis of the system architecture, including hardware, security, HMI, and peculiar challenges, for implementing V2X systems in motorcycles.

Ottimizzazione stocastica di una microrete con tecnologia "vehicle-to-grid"

La presente tesi ha come obiettivo quello di sviluppare un modello per la gestione ottimizzata delle unità di generazione e di accumulo di una microrete elettrica. La tesi analizza, come caso studio di riferimento, una microrete contenente impianti di generazione da fonti rinnovabili, sistemi di accumulo a batteria (BES:Battery Energy System) e stazioni di ricarica per veicoli elettrici. In particolare le stazioni di ricarica sono a flusso bidirezionale, in grado di fornire servizi di tipo "grid-to-vehicle"(G2V) e "vehicle-to-grid" (V2G). Il modello consente di definire, come sistema di dispacciamento centrale, le potenze che le varie risorse distribuite devono erogare o assorbire nella rete nelle 24 ore successive. Il dispacciamento avviene mediante risoluzione di un problema di minimizzazione dei costi operativi e dell'energia prelevata dalla rete esterna. Il problema è stato formulato tramite l'approccio di programmazione stocastica lineare dove i parametri incerti del modello sono modellizzati tramite processi stocastici. L'implementazione del modello è stata effettuata tramite il software AIMMS, un programma di ottimizzazione che prevede al suo interno delle funzionalità specifiche per la programmazione stocastica

Performance of LTE-V2V for Cooperative Awareness

The large scale development of an Intelligent Transportation System is very close. The main component of such a smart environment is the network that provides connectivity for all vehicles. Public safety is the most demanding application because requires a fast, reliable and secure communication. Although IEEE 802.11p is presently the only full wireless standard for vehicular communications, recent advancements in 3GPP LTE provide support to direct communications and the ongoing activities are also addressing the vehicle to vehicle case. This thesis focuses on the resource allocation procedures and performance of LTE-V2V. To this aim, a MATLAB simulator has been implemented and results have been obtained adopting different mobility models for both in-coverage and out-of-coverage scenarios.

Traffic Signal Optimization of Urban Arterial Network by Vehicle-to-Infrastructure

Urbanization has occasionally been linked to negative consequences. Traffic light system in urban arterial networks plays an essential role to the operation of transport systems. The availability of new Intelligent Transportation System innovations paved the way for connecting vehicles and road infrastructure. GLOSA, or the Green Light Optimal Speed Advisory, is a recent integration of vehicle-to-everything (v2x) technology. This thesis emphasized GLOSA system's potential as a tool for addressing traffic signal optimization. GLOSA serves as an advisory to drivers, informing them of the speed they must maintain to reduce waiting time. The considered study area in this thesis is the Via Aurelio Saffi – Via Emilia Ponente corridor in the Metropolitan City of Bologna which has several signalized intersections. Several simulation runs were performed in SUMOPy software on each peak-hour period (morning and afternoon) using recent actual traffic count data. GLOSA devices were placed on a 300m GLOSA distance. Considering the morning peak-hour, GLOSA outperformed the actuated traffic signal control, which is the baseline scenario, in terms of average waiting time, average speed, average fuel consumption per vehicle and average CO2 emissions. A remarkable 97% reduction on both fuel consumption and CO2 emissions were obtained. The average speed of vehicles running through the simulation was increased as well by 7% and a time saved of 25%. Same results were obtained for the afternoon peak hour with a decrease of 98% on both fuel consumption and CO2 emissions, 20% decrease on average waiting time, and an increase of 2% in average speed. In addition to previously mentioned benefits of GLOSA, a 15% and 13% decrease in time loss were obtained during morning and afternoon peak-hour, respectively. Towards the goal of sustainability, GLOSA shows a promising result of significantly lowering fuel consumption and CO2 emissions per vehicle.

Development of an innovative non rule-based energy management strategy for a Hybrid Electric Vehicle, structured for predictive driving controls based on external information knowledge

Recently, the interest of the automotive market for hybrid vehicles has increased due to the more restrictive pollutants emissions legislation and to the necessity of decreasing the fossil fuel consumption, since such solution allows a consistent improvement of the vehicle global efficiency. The term hybridization regards the energy flow in the powertrain of a vehicle: a standard vehicle has, usually, only one energy source and one energy tank; instead, a hybrid vehicle has at least two energy sources. In most cases, the prime mover is an internal combustion engine (ICE) while the auxiliary energy source can be mechanical, electrical, pneumatic or hydraulic. It is expected from the control unit of a hybrid vehicle the use of the ICE in high efficiency working zones and to shut it down when it is more convenient, while using the EMG at partial loads and as a fast torque response during transients. However, the battery state of charge may represent a limitation for such a strategy. That’s the reason why, in most cases, energy management strategies are based on the State Of Charge, or SOC, control. Several studies have been conducted on this topic and many different approaches have been illustrated. The purpose of this dissertation is to develop an online (usable on-board) control strategy in which the operating modes are defined using an instantaneous optimization method that minimizes the equivalent fuel consumption of a hybrid electric vehicle. The equivalent fuel consumption is calculated by taking into account the total energy used by the hybrid powertrain during the propulsion phases. The first section presents the hybrid vehicles characteristics. The second chapter describes the global model, with a particular focus on the energy management strategies usable for the supervisory control of such a powertrain. The third chapter shows the performance of the implemented controller on a NEDC cycle compared with the one obtained with the original control strategy.

Optimal bidding strategies of an electric vehicle aggregator in an electricity market

In recent years Electric Vehicles (EVs) are getting more importance as future transport systems, due to the increase of the concerns relevant to the greenhouse gases emission and the use fossil fuel. The management of the charging and discharging process of EVs could provide new business model for participating in the electricity markets. Moreover, vehicle to grid systems have the potential of increasing utility system flexibility. This thesis develops some models for the optimal integration of the EVs in the electricity market. In particular, the thesis focuses on the optimal bidding strategy of an EV aggregator participating to both the day ahead market and the secondary reserve market. The aggregator profit is maximized taking into account the energy balance equation, as well as the technical constraints of energy settlement, power supply and state of charge of the EVs. The results obtained by using the GAMS (General Algebraic Modelling System) environment are presented and discussed.

Design of an innovative electric vehicle simulator for Charging Systems' End-of-Line Testing

The trend related to the turnover of internal combustion engine vehicles with EVs goes by the name of electrification. The push electrification experienced in the last decade is linked to the still ongoing evolution in power electronics technology for charging systems. This is the reason why an evolution in testing strategies and testing equipment is crucial too. The project this dissertation is based on concerns the investigation of a new EV simulator design. that optimizes the structure of the testing equipment used by the company who commissioned this work. Project requirements can be summarized in the following two points: space occupation reduction and parallel charging implementation. Some components were completely redesigned, and others were substituted with equivalent ones that could perform the same tasks. In this way it was possible to reduce the space occupation of the simulator, as well as to increase the efficiency of the testing device. Moreover, the possibility of conjugating different charging simulations could be investigated by parallelly launching two testing procedures on a unique machine, properly predisposed for supporting the two charging protocols used. On the back of the results achieved in the body of this dissertation, a new design for the EV simulator was proposed. In this way, space reduction was obtained, and space occupation efficiency was improved with the proposed new design. The testing device thus resulted to be way more compact, enabling to gain in safety and productivity, along with a 25% cost reduction. Furthermore, parallel charging was implemented in the proposed new design since the conducted tests clearly showed the feasibility of parallel charging sessions. The results presented in this work can thus be implemented to build the first prototype of the new EV simulator.

Development of a Predictive Control Function for a Plug-in Hybrid Electric Vehicle with Electrically-heated Catalyst

This master thesis work is focused on the development of a predictive EHC control function for a diesel plug-in hybrid electric vehicle equipped with a EURO 7 compliant exhaust aftertreatment system (EATS), with the purpose of showing the advantages provided by the implementation of a predictive control strategy with respect to a rule-based one. A preliminary step will be the definition of an accurate powertrain and EATS physical model, starting from already existing and validated applications. Then, a rule-based control strategy managing the torque split between the electric motor (EM) and the internal combustion engine (ICE) will be developed and calibrated, with the main target of limiting tailpipe NOx emission by taking into account EM and ICE operating conditions together with EATS conversion efficiency. The information available from vehicle connectivity will be used to reconstruct the future driving scenario, also referred to as electronic horizon (eHorizon), and in particular to predict ICE first start. Based on this knowledge, an EATS pre-heating phase can be planned to avoid low pollutant conversion efficiencies, thus preventing high NOx emission due to engine cold start. Consequently, the final NOx emission over the complete driving cycle will be strongly reduced, allowing to comply with the limits potentially set by the incoming EURO 7 regulation. Moreover, given the same NOx emission target, the gain achieved thanks to the implementation of an EHC predictive control function will allow to consider a simplified EATS layout, thus reducing the related manufacturing cost. The promising results achieved in terms of NOx emission reduction show the effectiveness of the application of a predictive control strategy focused on EATS thermal management and highlight the potential of a complete integration and parallel development of involved vehicle physical systems, control software and connectivity data management.

An Image Recognition Software for Identification of Vehicle Homologation Tags

In recent years, we have witnessed great changes in the industrial environment as a result of the innovations introduced by Industry 4.0, especially in the integration of Internet of Things, Automation and Robotics in the manufacturing field. The project presented in this thesis lies within this innovation context and describes the implementation of an Image Recognition application focused on the automotive field. The project aims at helping the supply chain operator to perform an effective and efficient check of the homologation tags present on vehicles. The user contribution consists in taking a picture of the tag and the application will automatically, exploiting Amazon Web Services, return the result of the control about the correctness of the tag, the correct positioning within the vehicle and the presence of faults or defects on the tag. To implement this application we ombined two IoT platforms widely used in industrial field: Amazon Web Services(AWS) and ThingWorx. AWS exploits Convolutional Neural Networks to perform Text Detection and Image Recognition, while PTC ThingWorx manages the user interface and the data manipulation.

Distributed collision-free traffic management via vertex cover for multi-vehicle systems

In this thesis, we state the collision avoidance problem as a vertex covering problem, then we consider a distributed framework in which a team of cooperating Unmanned Vehicles (UVs) aim to solve this optimization problem cooperatively to guarantee collision avoidance between group members. For this purpose, we implement a distributed control scheme based on a robust Set-Theoretic Model Predictive Control ( ST-MPC) strategy, where the problem involves vehicles with independent dynamics but with coupled constraints, to capture required cooperative behavior.