Design and Implementation of Single phase 230V to Three Phase Inverter Based on the Embedded System STM-32 Applied to motor control

In the field of Power Electronics, several types of motor control systems have been developed using STM microcontroller and power boards. In both industrial power applications and domestic appliances, power electronic inverters are widely used. Inverters are used to control the torque, speed, and position of the rotor in AC motor drives. An inverter delivers constant-voltage and constant-frequency power in uninterruptible power sources. Because inverter power supplies have a high-power consumption and low transfer efficiency rate, a three-phase sine wave AC power supply was created using the embedded system STM32, which has low power consumption and efficient speed. It has the capacity of output frequency of 50 Hz and the RMS of line voltage. STM32 embedded based Inverter is a power supply that integrates, reduced, and optimized the power electronics application that require hardware system, software, and application solution, including power architecture, techniques, and tools, approaches capable of performance on devices and equipment. Power inverters are currently used and implemented in green energy power system with low energy system such as sensors or microcontroller to perform the operating function of motors and pumps. STM based power inverter is efficient, less cost and reliable. My thesis work was based on STM motor drives and control system which can be implemented in a gas analyser for operating the pumps and motors. It has been widely applied in various engineering sectors due to its ability to respond to adverse structural changes and improved structural reliability. The present research was designed to use STM Inverter board on low power MCU such as NUCLEO with some practical examples such as Blinking LED, and PWM. Then we have implemented a three phase Inverter model with Steval-IPM08B board, which converter single phase 230V AC input to three phase 380 V AC output, the output will be useful for operating the induction motor.

Design and Characterization of an Active Three-Phase EMI Noise Separator for Three-Phase Power Electronics Systems

One of the major issues for power converters that are connected to the electric grid are the measurement of three phase Conduced Emissions (CE), which are regulated by international and regional standards. CE are composed of two components which are Common Mode (CM) noise and Differential Mode (DM) noise. To achieve compliance with these regulations the Equipment Under Test (EUT) includes filtering and other electromagnetic emission control strategies. The separation of differential mode and common mode noise in Electromagnetic Interference (EMI) analysis is a well-known procedure which is useful especially for the optimization of the EMI filter, to improve the CM or DM attenuation depending on which component of the conducted emissions is predominant, and for the analysis and the understanding of interference phenomena of switched mode power converters. However, separating both components is rarely done during measurements. Therefore, in this thesis an active device for the separation of the CM and DM EMI noise in three phase power electronic systems has been designed and experimentally analysed.

Genetic variability and differentiation in the Mediterranean endemic starry ray Raja asterias (Delaroche, 1809)

The present study deal with the population structure and connectivity of the Mediterranean endemic starry ray Raja asterias (Delaroche, 1809) in the Western and Eastern Mediterranean basin. A panel of eight microsatellite loci which cross-amplify in Rajidae (El Nagar, 2010) was used to assess population connectivity and structure. Those aims were investigated by analyzing the genetic variation of 9 population sample for a total of 185 individuals collected during past scientific surveys (MEDITS, GRUND), commercial trawling and also directly at fish markets. The purpose of this thesis is to estimate the genetic divergence occurring between the Mediterranean populations and, in particular, to assess the presence of any barrier (geographic, hydrogeological and biological) to gene flow for this species. Different statistical approaches were performed to reach this aim evaluating both the genetic diversity (nucleotide diversity, allelic richness, observed and expected heterozygosity and Hardy-Weinberg equilibrium test) and the population differentiation patterns (pairwise Fst estimated and population structure analysis). The results obtained from the analysis of the microsatellite dataset suggest a geographic and genetic separation between the starry ray populations of the Mediterranean basin into three or four distinct groups: Western and Eastern Mediterranean basins and Sicilian coast always clustering as an independent group and Algeria which could be or not considered another separate group. The data were discussed from both an evolutionary and a conservation point of view and in relation to previous results obtained by the analysis of mitochondrial marker. A comparison with other Mediterranean demersal skate species was performed in order to better contextualise our results. Finally, our results could offer useful information to protect vulnerable species as R. asterias and developing effective conservation plans in the Mediterranean.