Sviluppo di una strategia per l’individuazione di squilibri di titolo tra cilindri di un motore a combustione interna

L’oggetto di questa tesi è l’individuazione di un metodo in grado di rilevare uno squilibrio cilindrico rilevante in un motore a combustione interna ad accensione comandata, sovralimentato dinamicamente. Il progetto si basa sull’osservazione sperimentale di un forte incremento dei valori assunti da indici basati sulla differenza dei tempi dente della ruota fonica, al manifestarsi di un brusco squilibrio di titolo in uno dei quattro cilindri. Ciò ha permesso di rilevare eventuali sbilanciamenti di titolo mediante una diagnosi intrusiva in grado di esaltarli. Questa metodologia a differenza di quelle basate sul segnale proveniente dalla sonda lambda, non risente del problema del mixing dei pacchetti di gas combusti all’interno della turbina. Il lavoro di tesi è consistito nel concepire un indice di rilevamento capace di esaltare il fenomeno sopra descritto, nel creare in ambiente Matlab-Simulink un modello che simuli la strategia in questione e renda possibile la realizzazione di un prototipo, per mezzo del quale è stata validata la strategia a bordo del veicolo. This thesis proposes a methodology to detect a relevant cylinder imbalance by means of flywheel speed fluctuation analysis in a turbocharged internal combustion engine. The main idea behind this project is the evidence that every time a significant cylinder imbalance is present, it is noticed an important increase of index based on tooth time sampled via flywheel. For this reason, it is possible to develop an intrusive strategy, which higliaghts a possible cylinder imbalance presence, in order to detect it. This method, unlike others based on the signal coming from Lambda sensor, doesn’t suffer from the presence of exhaust gases mixing effect inside the turbine. The objective of this thesis is to conceive a detection index able to put in evidence the phenomena described above, and to design a model inside the Matlab-Simulink environment, able to simulate the strategy and to make possible tests on the vehicle by means of a prototype.

Analysis of aircraft load spectrum by means of flight simulator

Damage tolerance analysis is a quite new methodology based on prescribed inspections. The load spectra used to derive results of these analysis strongly influence the final defined inspections programs that for this reason must be as much as possible representative of load acting on the considered structural component and at the same time, obtained reducing both cost and time. The principal purpose of our work is in improving the actual condition developing a complete numerical Damage Tolerance analysis, able to prescribe inspection programs on typical aircraft critical components, respecting DT regulations, starting from much more specific load spectrum then those actually used today. In particular, these more specific load spectrum to design against fatigue have been obtained through an appositively derived flight simulator developed in a Matlab/Simulink environment. This dynamic model has been designed so that it can be used to simulate typical missions performing manually (joystick inputs) or completely automatic (reference trajectory need to be provided) flights. Once these flights have been simulated, model’s outputs are used to generate load spectrum that are then processed to get information (peaks, valleys) to perform statistical and/or comparison consideration with other load spectrum. However, also much more useful information (loads amplitude) have been extracted from these generated load spectrum to perform the previously mentioned predictions (Rainflow counting method is applied for this purpose). The entire developed methodology works in a complete automatic way, so that, once some specified input parameters have been introduced and different typical flights have been simulated both, manually or automatically, it is able to relate the effects of these simulated flights with the reduction of residual strength of the considered component.

Modeling and validation of the thermal behavior of buildings for the development of demand response methods

The representation of the thermal behaviour of the building is achieved through a relatively simple dynamic model that takes into account the effects due to the thermal mass of the building components. The model of a intra-floor apartment has been built in the Matlab-Simulink environment and considers the heat transmission through the external envelope, wall and windows, the internal thermal masses, (i.e. furniture, internal wall and floor slabs) and the sun gain due to opaque and see-through surfaces of the external envelope. The simulations results for the entire year have been compared and the model validated, with the one obtained with the dynamic building simulation software Energyplus.

Advanced 4DT flight guidance and control software system

The work presented in this thesis has been part of a Cranfield University research project. This thesis aims to design a flight control law for large cargo aircraft by using predictive control, which can assure flight motion along the flight path exactly and on time. In particular this work involves the modelling of a Boeing C-17 Globemaster III 6DOF model (used as study case), by using DATCOM and Matlab Simulink software. Then a predictive control algorithm has been developed. The majority of the work is done in a Matlab/Simulink environment. Finally the predictive control algorithm has been applied on the aircraft model and its performances, in tracking given trajectory optimized through a 4DT Research Software, have been evaluated.