Analysis of aircraft load spectrum by means of flight simulator

Damage tolerance analysis is a quite new methodology based on prescribed inspections. The load spectra used to derive results of these analysis strongly influence the final defined inspections programs that for this reason must be as much as possible representative of load acting on the considered structural component and at the same time, obtained reducing both cost and time. The principal purpose of our work is in improving the actual condition developing a complete numerical Damage Tolerance analysis, able to prescribe inspection programs on typical aircraft critical components, respecting DT regulations, starting from much more specific load spectrum then those actually used today. In particular, these more specific load spectrum to design against fatigue have been obtained through an appositively derived flight simulator developed in a Matlab/Simulink environment. This dynamic model has been designed so that it can be used to simulate typical missions performing manually (joystick inputs) or completely automatic (reference trajectory need to be provided) flights. Once these flights have been simulated, model’s outputs are used to generate load spectrum that are then processed to get information (peaks, valleys) to perform statistical and/or comparison consideration with other load spectrum. However, also much more useful information (loads amplitude) have been extracted from these generated load spectrum to perform the previously mentioned predictions (Rainflow counting method is applied for this purpose). The entire developed methodology works in a complete automatic way, so that, once some specified input parameters have been introduced and different typical flights have been simulated both, manually or automatically, it is able to relate the effects of these simulated flights with the reduction of residual strength of the considered component.

Design and implementation of the ESEO spacecraft simulator

The thesis work is developed under the European Student Earth Orbiter (ESEO) project supported by the European Space Agency (ESA) in order to help prepare a well-qualified space-engineering workforce for Europe's future. In the following chapters we are going to analyse how to simulate some ESEO subsystem. First of all, the Thermal Subsystem that evaluates the temperature evolution of on-board instruments. For this purpose, simulating also the orbital and attitude dynamics of the spacecraft, it is necessary in order to evaluate external environmental fluxes. The Power Subsystem will be the following step and it models the ability of a spacecraft to produce and store electrical energy. Finally, we will integrate in our software a block capable of simulating the communication link between the satellite and the Ground Station (GS). This last step is designed and validated during the thesis preparation.

Design, implementation and performance evaluation of an anonymous distributed simulator

La simulazione è definita come la rappresentazione del comportamento di un sistema o di un processo per mezzo del funzionamento di un altro o, alternativamente, dall'etimologia del verbo “simulare”, come la riproduzione di qualcosa di fittizio, irreale, come se in realtà, lo fosse. La simulazione ci permette di modellare la realtà ed esplorare soluzioni differenti e valutare sistemi che non possono essere realizzati per varie ragioni e, inoltre, effettuare differenti valutazioni, dinamiche per quanto concerne la variabilità delle condizioni. I modelli di simulazione possono raggiungere un grado di espressività estremamente elevato, difficilmente un solo calcolatore potrà soddisfare in tempi accettabili i risultati attesi. Una possibile soluzione, viste le tendenze tecnologiche dei nostri giorni, è incrementare la capacità computazionale tramite un’architettura distribuita (sfruttando, ad esempio, le possibilità offerte dal cloud computing). Questa tesi si concentrerà su questo ambito, correlandolo ad un altro argomento che sta guadagnando, giorno dopo giorno, sempre più rilevanza: l’anonimato online. I recenti fatti di cronaca hanno dimostrato quanto una rete pubblica, intrinsecamente insicura come l’attuale Internet, non sia adatta a mantenere il rispetto di confidenzialità, integrità ed, in alcuni, disponibilità degli asset da noi utilizzati: nell’ambito della distribuzione di risorse computazionali interagenti tra loro, non possiamo ignorare i concreti e molteplici rischi; in alcuni sensibili contesti di simulazione (e.g., simulazione militare, ricerca scientifica, etc.) non possiamo permetterci la diffusione non controllata dei nostri dati o, ancor peggio, la possibilità di subire un attacco alla disponibilità delle risorse coinvolte. Essere anonimi implica un aspetto estremamente rilevante: essere meno attaccabili, in quanto non identificabili.

Motion Cueing Algorithm Development in a 2DOF Driving Simulator: a Driving Behaviour-Centered Approach

I simulatori di guida sono strumenti altamente tecnologici che permettono di svolgere attività di ricerca in vari ambiti quali la psicologia, la medicina e l’ingegneria. Tuttavia, affinché i dati ottenuti mediante le simulazioni siano rapportabili alla loro controparte reale, la fedeltà delle componenti del simulatore di guida deve essere elevata. Questo lavoro tratta del miglioramento del sistema di restituzione del movimento nel simulatore a due gradi di libertà (2DOF) SIMU-LACET Driving Simulator, costruito e sviluppato presso il laboratorio LEPSIS dell’IFSTTAR (Istituto Francese delle Scienze e Tecnologie dei Trasporti, dello Sviluppo e delle Reti), in particolare nella sua sede di Parigi – Marne-la-Vallée. Si è deciso di andare a riprogettare la parte software del sistema di restituzione del movimento (motion cueing), operando su due elementi principali: lo scale factor (fattore di scala) applicato agli impulsi dinamici provenienti dal modello veicolare e i Motion Cueing Algorihms (MCA, algoritmi di restituzione del movimento), questo per entrambi i gradi di libertà. Si è quindi intervenuti sul modello esistente implementato in MATLAB-Simulink nello specifico blocco del motion cueing sul surge (traslazione longitudinale) e sul yaw (imbardata). Riguardo lo scale factor, è stata introdotta una metodologia per creare uno scale factor non lineare in forma esponenziale, tale da migliorare la restituzione degli impulsi meno ampi, pur rispettando i limiti fisici della piattaforma di movimento. Per quanto concerne il MCA, si sono vagliate diverse transfer function dell’algoritmo classico. La scelta finale dei MCA e la validazione del motion cueig in genere è stata effettuata mediante due esperimenti ed il giudizio dei soggetti che vi hanno partecipato. Inoltre, in virtù dei risultati del primo esperimento, si è investigata l’influenza che la strategia in merito al cambio delle marce avesse sulla percezione del movimento da parte del guidatore.

Design of an innovative electric vehicle simulator for Charging Systems' End-of-Line Testing

The trend related to the turnover of internal combustion engine vehicles with EVs goes by the name of electrification. The push electrification experienced in the last decade is linked to the still ongoing evolution in power electronics technology for charging systems. This is the reason why an evolution in testing strategies and testing equipment is crucial too. The project this dissertation is based on concerns the investigation of a new EV simulator design. that optimizes the structure of the testing equipment used by the company who commissioned this work. Project requirements can be summarized in the following two points: space occupation reduction and parallel charging implementation. Some components were completely redesigned, and others were substituted with equivalent ones that could perform the same tasks. In this way it was possible to reduce the space occupation of the simulator, as well as to increase the efficiency of the testing device. Moreover, the possibility of conjugating different charging simulations could be investigated by parallelly launching two testing procedures on a unique machine, properly predisposed for supporting the two charging protocols used. On the back of the results achieved in the body of this dissertation, a new design for the EV simulator was proposed. In this way, space reduction was obtained, and space occupation efficiency was improved with the proposed new design. The testing device thus resulted to be way more compact, enabling to gain in safety and productivity, along with a 25% cost reduction. Furthermore, parallel charging was implemented in the proposed new design since the conducted tests clearly showed the feasibility of parallel charging sessions. The results presented in this work can thus be implemented to build the first prototype of the new EV simulator.

Design and implementation of an optimal motion cueing algorithm for the Stuttgart Driving Simulator

Driving simulators emulate a real vehicle drive in a virtual environment. One of the most challenging problems in this field is to create a simulated drive as real as possible to deceive the driver's senses and cause the believing to be in a real vehicle. This thesis first provides an overview of the Stuttgart driving simulator with a description of the overall system, followed by a theoretical presentation of the commonly used motion cueing algorithms. The second and predominant part of the work presents the implementation of the classical and optimal washout algorithms in a Simulink environment. The project aims to create a new optimal washout algorithm and compare the obtained results with the results of the classical washout. The classical washout algorithm, already implemented in the Stuttgart driving simulator, is the most used in the motion control of the simulator. This classical algorithm is based on a sequence of filters in which each parameter has a clear physical meaning and a unique assignment to a single degree of freedom. However, the effects on human perception are not exploited, and each parameter must be tuned online by an engineer in the control room, depending on the driver's feeling. To overcome this problem and also consider the driver's sensations, the optimal washout motion cueing algorithm was implemented. This optimal control-base algorithm treats motion cueing as a tracking problem, forcing the accelerations perceived in the simulator to track the accelerations that would have been perceived in a real vehicle, by minimizing the perception error within the constraints of the motion platform. The last chapter presents a comparison between the two algorithms, based on the driver's feelings after the test drive. Firstly it was implemented an off-line test with a step signal as an input acceleration to verify the behaviour of the simulator. Secondly, the algorithms were executed in the simulator during a test drive on several tracks.

SmartForge: An event-driven architecture for simulator-based process optimization

In the metal industry, and more specifically in the forging one, scrap material is a crucial issue and reducing it would be an important goal to reach. Not only would this help the companies to be more environmentally friendly and more sustainable, but it also would reduce the use of energy and lower costs. At the same time, the techniques for Industry 4.0 and the advancements in Artificial Intelligence (AI), especially in the field of Deep Reinforcement Learning (DRL), may have an important role in helping to achieve this objective. This document presents the thesis work, a contribution to the SmartForge project, that was performed during a semester abroad at Karlstad University (Sweden). This project aims at solving the aforementioned problem with a business case of the company Bharat Forge Kilsta, located in Karlskoga (Sweden). The thesis work includes the design and later development of an event-driven architecture with microservices, to support the processing of data coming from sensors set up in the company's industrial plant, and eventually the implementation of an algorithm with DRL techniques to control the electrical power to use in it.

Analisi del comportamento a caldo dell'acciaio AISI - H11 per la stima della vita utile di matrici per estrusione

The effect of process parameters on the creep-fatigue behavior of a hot-work tool steel for aluminum extrusion die was investigated through a technological test in which the specimen geometry resembled the mandrel of a hollow extrusion die. Tests were performed on a Gleeble thermomechanical simulator by heating the specimen using joule’s effect and by applying cyclic loading up to 6.30 h or till specimen failure. Displacements during the tests at 380, 490, 540 and 580°C and under the average stresses of 400, 600 and 800 MPa were determined. In the first set of test a dwell time of 3 min was introduced during each of the tests to understand the creep behavior. The results showed that the test could indeed physically simulate the cyclic loading on the hollow die during extrusion and reveal all the mechanisms of creep-fatigue interaction. In the second set a pure fatigue laod were induced and in the third set a static creep load were induced in the specimens. Furher type of tests, finite element and microstructural analysis were presented.

Politiofeni regioregolari funzionalizzati per applicazioni fotovoltaiche

Studi preliminari condotti dal gruppo di ricerca presso il quale ho svolto il mio lavoro di tesi, avevano dimostrato che il poli[3-(6-bromoesil)tiofene] non regioregolare funzionalizzato con idrossifenilporfirina [TPPOH] può essere utilizzato con successo per la realizzazione di celle fotovoltaiche. Il presente lavoro di tesi di laurea magistrale è stato quindi incentrato sulla sintesi e caratterizzazione di un campione di poli[3-(6-bromoesil)tiofene] [PT6Br] ad elevata regioregolarità e sulla sua successiva funzionalizzazione con diverse percentuali di 5-(4-idrossifenil)-10,15,20-trifenilporfirina [TPPOH] per ottenere i copolimeri poli[3-(6-bromoesil)tiofene-co-(3-[5-(4-fenossi)-10,15,20-trifenilporfinil]esiltiofene)] [P(T6Br-co-T6TPP)], anch’essi con elevata percentuale di concatenamenti testa-coda, al fine di valutare se la regioregolarità del polimero sia in grado di migliorare l’efficienza fotovoltaica. Il campione che ha fornito i risultati migliori è stato poi ulteriormente testato eseguendo prove su celle trattate termicamente per tempi diversi, in modo tale da verificare come la durata del riscaldamento, che incide sull’organizzazione strutturale del materiale, influisca sulle prestazioni ottenibili dalla cella stessa. I prodotti polimerici sintetizzati sono stati caratterizzati mediante tecniche spettroscopiche (NMR, FT-IR, UV-Vis), ne sono determinate le proprietà termiche ed i pesi molecolari medi e la relativa distribuzione, mediante cromatografia a permeazione su gel (GPC). Le prestazioni delle celle fotovoltaiche realizzate utilizzando i copolimeri prodotti sono state misurate tramite un multimetro Keithley ed un Solar Simulator, che permette di riprodurre l’intero spettro della radiazione solare.

Lifecycle analysis for surgery instruments at a hospital

Gli strumenti chirurgici sono importanti “devices” utilizzati come supporto indi-spensabile nella cura di pazienti negli ospedali. Essi sono caratterizzati da un intero ciclo di vita che inizia convenzionalmente nello “Store”, dove gli strumenti sterilizzati sono prelevati per essere utilizzati all’interno delle sale operatorie, e termina nuovamente nello “Store”, dove gli strumenti vengono immagazzinati per essere riutilizzati in un nuovo ciclo. Può accadere che le singole fasi del ciclo subiscano ritardi rispetto ai tempi previ-sti, non assicurando, pertanto, nelle sale operatorie, il corretto numero degli stru-menti secondo i tempi programmati. Il progetto che vado ad illustrare ha come obiettivo l’ottimizzazione del ciclo degli strumenti chirurgici all’interno di un nuovo ospedale, applicando i principi della Lean philosophy ed in particolare i metodi: “Poke Yoke, 5S e tracciabilità”. Per raggiungere tale scopo, il progetto è stato articolato come segue. In un primo momento si è osservato l’intero ciclo di vita degli strumenti nei due principali ospedali di Copenhagen (Hervel e Gentofte hospital). Ciò ha permesso di rilevare gli steps del ciclo, nonché di riscontrare sul campo i principali problemi relativi al ciclo stesso quali: bassa flessiblità, decentramento dei differenti reparti di cleaning e di store rispetto alle operation theatres ed un problema nel solleva-mento degli strumenti pesanti. Raccolte le dovute informazioni, si è passati alla fase sperimentale, in cui sono stati mappati due cicli di vita differenti, utilizzando tre strumenti di analisi: • Idef0 che consente di avere una visione gerarchica del ciclo; • Value stream Mapping che permette di evidenziare i principali sprechi del ciclo; • Simulator Tecnomatix che favorisce un punto di vista dinamico dell’analisi. Il primo ciclo mappato è stato creato con il solo scopo di mettere in risalto gli steps del ciclo e alcuni problemi rincontrati all’interno degli ospedali visitati. Il secondo ciclo, invece, è stato creato in ottica Lean al fine di risolvere alcuni tra i principali problemi riscontrati nei due ospedali e ottimizzare il primo ciclo. Si ricordi, infatti, che nel secondo ciclo le principali innovazioni introdotte sono state: l’utilizzo del Barcode e Rfid Tag per identificare e tracciare la posizione degli items, l’uso di un “Automatic and Retrievial Store” per minimizzare i tempi di inserimento e prelievo degli items e infine l’utilizzo di tre tipologie di carrello, per consentire un flessibile servizio di cura. Inoltre sono state proposte delle solu-zioni “Poke-Yoke” per risolvere alcuni problemi manuali degli ospedali. Per evidenziare il vantaggio del secondo ciclo di strumenti, è stato preso in consi-derazione il parametro “Lead time”e le due simulazioni, precedentemente create, sono state confrontate. Tale confronto ha evidenziato una radicale riduzione dei tempi (nonché dei costi associati) della nuova soluzione rispetto alla prima. Alla presente segue la trattazione in lingua inglese degli argomenti oggetto di ri-cerca. Buona lettura.

Progettazione e sviluppo di un RVE (Reconfigurable Virtual Environment) per applicazioni nei settori dell’ingegneria industriale

Il presente elaborato descrive la realizzazione, presso il Laboratorio di Realtà Virtuale e Simulazione della Seconda Facoltà di Ingegneria, di un RVE (Reconfigurable Virtual Environment), per applicazioni nei settori dell’ingegneria industriale. La tesi ripercorre la fase di progettazione del sistema basato sull'integrazione di componenti COTS. E' definito, inoltre, un insieme di applicazioni target nei settori dell'ingegneria industriale di cui si valuta la compatibilità con il Virtual Environment. L'elaborato si conclude con la presentazione dei risultati e dei possibili sviluppi futuri.

Numerical simulation of interdigitated back contact hetero-junction solar cells

The goal of this thesis is the application of an opto-electronic numerical simulation to heterojunction silicon solar cells featuring an all back contact architecture (Interdigitated Back Contact Hetero-Junction IBC-HJ). The studied structure exhibits both metal contacts, emitter and base, at the back surface of the cell with the objective to reduce the optical losses due to the shadowing by front contact of conventional photovoltaic devices. Overall, IBC-HJ are promising low-cost alternatives to monocrystalline wafer-based solar cells featuring front and back contact schemes, in fact, for IBC-HJ the high concentration doping diffusions are replaced by low-temperature deposition processes of thin amorphous silicon layers. Furthermore, another advantage of IBC solar cells with reference to conventional architectures is the possibility to enable a low-cost assembling of photovoltaic modules, being all contacts on the same side. A preliminary extensive literature survey has been helpful to highlight the specific critical aspects of IBC-HJ solar cells as well as the state-of-the-art of their modeling, processing and performance of practical devices. In order to perform the analysis of IBC-HJ devices, a two-dimensional (2-D) numerical simulation flow has been set up. A commercial device simulator based on finite-difference method to solve numerically the whole set of equations governing the electrical transport in semiconductor materials (Sentuarus Device by Synopsys) has been adopted. The first activity carried out during this work has been the definition of a 2-D geometry corresponding to the simulation domain and the specification of the electrical and optical properties of materials. In order to calculate the main figures of merit of the investigated solar cells, the spatially resolved photon absorption rate map has been calculated by means of an optical simulator. Optical simulations have been performed by using two different methods depending upon the geometrical features of the front interface of the solar cell: the transfer matrix method (TMM) and the raytracing (RT). The first method allows to model light prop-agation by plane waves within one-dimensional spatial domains under the assumption of devices exhibiting stacks of parallel layers with planar interfaces. In addition, TMM is suitable for the simulation of thin multi-layer anti reflection coating layers for the reduction of the amount of reflected light at the front interface. Raytracing is required for three-dimensional optical simulations of upright pyramidal textured surfaces which are widely adopted to significantly reduce the reflection at the front surface. The optical generation profiles are interpolated onto the electrical grid adopted by the device simulator which solves the carriers transport equations coupled with Poisson and continuity equations in a self-consistent way. The main figures of merit are calculated by means of a postprocessing of the output data from device simulation. After the validation of the simulation methodology by means of comparison of the simulation result with literature data, the ultimate efficiency of the IBC-HJ architecture has been calculated. By accounting for all optical losses, IBC-HJ solar cells result in a theoretical maximum efficiency above 23.5% (without texturing at front interface) higher than that of both standard homojunction crystalline silicon (Homogeneous Emitter HE) and front contact heterojuction (Heterojunction with Intrinsic Thin layer HIT) solar cells. However it is clear that the criticalities of this structure are mainly due to the defects density and to the poor carriers transport mobility in the amorphous silicon layers. Lastly, the influence of the most critical geometrical and physical parameters on the main figures of merit have been investigated by applying the numerical simulation tool set-up during the first part of the present thesis. Simulations have highlighted that carrier mobility and defects level in amorphous silicon may lead to a potentially significant reduction of the conversion efficiency.

Sintesi e proprieta di copolimeri tiofenici funzionalizzati per applicazioni fotovoltaiche

Il presente lavoro di tesi di laurea magistrale è stato incentrato sulla sintesi e caratterizzazione di due copolimeri regioregolari poli[3-esiltiofene-co-(3-[5-(4-fenossi)-10,15,20-trifenilporfinil]esiltiofene)] contenenti diversa percentuale di sostituente porfirinico, ottenuti per post-funzionalizzazione con 5-(4-idrossifenil)-10,15,20-trifenilporfirina di due copolimeri regioregolari poli[3-esiltiofene-co-(3-(6-bromoesil)tiofene)] contenenti diverse percentuali di sostituente esilico bromurato, appositamente sintetizzati. E’ stato inoltre preparato il copolimero non regioregolare poli[3-dodeciltiofene-co-(3-[5-(4-fenossi)-10,15,20-trifenilporfinil]esiltiofene)] partendo da un comonomero con una catena alchilica laterale più lunga, il 3-dodeciltiofene, per evitare l’eventuale insolubilità del copolimero finale e per avere un ulteriore termine di paragone derivante dall’utilizzo di catene alchiliche di diversa lunghezza. I prodotti polimerici sintetizzati sono stati caratterizzati mediante tecniche spettroscopiche (NMR, FT-IR, UV-Vis), ne sono state determinate le proprietà termiche tramite analisi DSC e TGA ed i pesi molecolari medi con la relativa distribuzione, mediante cromatografia a permeazione su gel (GPC). Tali derivati sono stati successivamente testati attraverso prove di preparazione e caratterizzazione di dispositivi fotovoltaici, Le prestazioni delle celle fotovoltaiche realizzate utilizzando i copolimeri prodotti sono state misurate tramite un multimetro Keithley ed un Solar Simulator, che permette di riprodurre l’intero spettro della radiazione solare.

Sea level measurement using single GNSS antenna SNR signals

This thesis presents a possible method to calculate sea level variation using geodetic-quality Global Navigate Satellite System (GNSS) receivers. Three antennas are used: two small antennas and a choke ring one, analyzing only Global Positioning System signals. The main goal of the thesis is to test a modified configuration for antenna set up. In particular, measurements obtained tilting one antenna to face the horizon are compared to measurements obtained from antennas looking upward. The location of the experiment is a coastal environment nearby the Onsala Space Observatory in Sweden. Sea level variations are obtained using periodogram analysis of the SNR signal and compared to synthetic gauge generated from two independent tide gauges. The choke ring antenna provides poor result, with an RMS around 6 cm and a correlation coefficients of 0.89. The smaller antennas provide correlation coefficients around 0.93. The antenna pointing upward present an RMS of 4.3 cm and the one pointing the horizon an RMS of 6.7 cm. Notable variation in the statistical parameters is found when modifying the length of the interval analyzed. In particular, doubts are risen on the reliability of certain scattered data. No relation is found between the accuracy of the method and weather conditions. Possible methods to enhance the available data are investigated, and correlation coefficient above 0.97 can be obtained with small antennas when sacrificing data points. Hence, the results provide evidence of the suitability of SNR signal analysis for sea level variation in coastal environment even in the case of adverse weather conditions. In particular, tilted configurations provides comparable result with upward looking geodetic antennas. A SNR signal simulator is also tested to investigate its performance and usability. Various configuration are analyzed in combination with the periodogram procedure used to calculate the height of reflectors. Consistency between the data calculated and those received is found, and the overall accuracy of the height calculation program is found to be around 5 mm for input height below 5 m. The procedure is thus found to be suitable to analyze the data provided by the GNSS antennas at Onsala.

Simulation of visible light communications in vehicular networks

The rapid development in the field of lighting and illumination allows low energy consumption and a rapid growth in the use, and development of solid-state sources. As the efficiency of these devices increases and their cost decreases there are predictions that they will become the dominant source for general illumination in the short term. The objective of this thesis is to study, through extensive simulations in realistic scenarios, the feasibility and exploitation of visible light communication (VLC) for vehicular ad hoc networks (VANETs) applications. A brief introduction will introduce the new scenario of smart cities in which visible light communication will become a fundamental enabling technology for the future communication systems. Specifically, this thesis focus on the acquisition of several, frequent, and small data packets from vehicles, exploited as sensors of the environment. The use of vehicles as sensors is a new paradigm to enable an efficient environment monitoring and an improved traffic management. In most cases, the sensed information must be collected at a remote control centre and one of the most challenging aspects is the uplink acquisition of data from vehicles. My thesis discusses the opportunity to take advantage of short range vehicle-to-vehicle (V2V) and vehicle-to-roadside (V2R) communications to offload the cellular networks. More specifically, it discusses the system design and assesses the obtainable cellular resource saving, by considering the impact of the percentage of vehicles equipped with short range communication devices, of the number of deployed road side units, and of the adopted routing protocol. When short range communications are concerned, WAVE/IEEE 802.11p is considered as standard for VANETs. Its use together with VLC will be considered in urban vehicular scenarios to let vehicles communicate without involving the cellular network. The study is conducted by simulation, considering both a simulation platform (SHINE, simulation platform for heterogeneous interworking networks) developed within the Wireless communication Laboratory (Wilab) of the University of Bologna and CNR, and network simulator (NS3). trying to realistically represent all the wireless network communication aspects. Specifically, simulation of vehicular system was performed and introduced in ns-3, creating a new module for the simulator. This module will help to study VLC applications in VANETs. Final observations would enhance and encourage potential research in the area and optimize performance of VLC systems applications in the future.