Experimental Study on Friction between Saline Ice and Steel

Understanding the interaction of sea ice with offshore structures is of primary importance for the development of technology in cold climate regions. The rheological properties of sea ice (strength, creep, viscosity) as well as the roughness of the contact surface are the main factors influencing the type of interaction with a structure. A device was developed and designed and small scale laboratory experiments were carried out to study sea ice frictional interaction with steel material by means of a uniaxial compression rig. Sea-ice was artificially grown between a stainless steel piston (of circular cross section) and a hollow cylinder of the same material, coaxial to the former and of the same surface roughness. Three different values for the roughness were tested: 1.2, 10 and 30 μm Ry (maximum asperities height), chosen as representative values for typical surface conditions, from smooth to normally corroded steel. Creep tests (0.2, 0.3, 0.4 and 0.6 kN) were conducted at T = -10 ºC. By pushing the piston head towards the cylinder base, three different types of relative movement were observed: 1) the piston slid through the ice, 2) the piston slid through the ice and the ice slid on the surface of the outer cylinder, 3) the ice slid only on the cylinder surface. A cyclic stick-slip motion of the piston was detected with a representative frequency of 0.1 Hz. The ratio of the mean rate of axial displacement to the frequency of the stick-slip oscillations was found to be comparable to the roughness length (Sm). The roughness is the most influential parameter affecting the amplitude of the oscillations, while the load has a relevant influence on the their frequency. Guidelines for further investigations were recommended. Marco Nanetti - seloselo@virgilio.it

"Offshore tower or platform foundations: numerical analysis of a laterally loaded single pile or pile group in soft clay and analysis of actions on a jacket structure"

Laterally loaded piles are a typical situation for a large number of cases in which deep foundations are used. Dissertation herein reported, is a focus upon the numerical simulation of laterally loaded piles. In the first chapter the best model settings are largely discussed, so a clear idea about the effects of interface adoption, model dimension, refinement cluster and mesh coarseness is reached. At a second stage, there are three distinct parametric analyses, in which the model response sensibility is studied for variation of interface reduction factor, Eps50 and tensile cut-off. In addition, the adoption of an advanced soil model is analysed (NGI-ADP). This was done in order to use the complex behaviour (different undrained shear strengths are involved) that governs the resisting process of clay under short time static loads. Once set a definitive model, a series of analyses has been carried out with the objective of defining the resistance-deflection (P-y) curves for Plaxis3D (2013) data. Major results of a large number of comparisons made with curves from API (America Petroleum Institute) recommendation are that the empirical curves have almost the same ultimate resistance but a bigger initial stiffness. In the second part of the thesis a simplified structural preliminary design of a jacket structure has been carried out to evaluate the environmental forces that act on it and on its piles foundation. Finally, pile lateral response is studied using the empirical curves.

Polar Codes for error correction: Analysis and Decoding Algorithms

I Polar Codes sono la prima classe di codici a correzione d’errore di cui è stato dimostrato il raggiungimento della capacità per ogni canale simmetrico, discreto e senza memoria, grazie ad un nuovo metodo introdotto recentemente, chiamato ”Channel Polarization”. In questa tesi verranno descritti in dettaglio i principali algoritmi di codifica e decodifica. In particolare verranno confrontate le prestazioni dei simulatori sviluppati per il ”Successive Cancellation Decoder” e per il ”Successive Cancellation List Decoder” rispetto ai risultati riportati in letteratura. Al fine di migliorare la distanza minima e di conseguenza le prestazioni, utilizzeremo uno schema concatenato con il polar code come codice interno ed un CRC come codice esterno. Proporremo inoltre una nuova tecnica per analizzare la channel polarization nel caso di trasmissione su canale AWGN che risulta il modello statistico più appropriato per le comunicazioni satellitari e nelle applicazioni deep space. In aggiunta, investigheremo l’importanza di una accurata approssimazione delle funzioni di polarizzazione.