Development of Optimal Energy Management Strategies for a Hybrid Boat

The present work proposes different approaches to extend the mathematical methods of supervisory energy management used in terrestrial environments to the maritime sector, that diverges in constraints, variables and disturbances. The aim is to find the optimal real-time solution that includes the minimization of a defined track time, while maintaining the classical energetic approach. Starting from analyzing and modelling the powertrain and boat dynamics, the energy economy problem formulation is done, following the mathematical principles behind the optimal control theory. Then, an adaptation aimed in finding a winning strategy for the Monaco Energy Boat Challenge endurance trial is performed via ECMS and A-ECMS control strategies, which lead to a more accurate knowledge of energy sources and boat’s behaviour. The simulations show that the algorithm accomplishes fuel economy and time optimization targets, but the latter adds huge tuning and calculation complexity. In order to assess a practical implementation on real hardware, the knowledge of the previous approaches has been translated into a rule-based algorithm, that let it be run on an embedded CPU. Finally, the algorithm has been tuned and tested in a real-world race scenario, showing promising results.

Ecological modelling of the phytoplankton dynamics in the northern Gulf of Aqaba (Red Sea)

The Gulf of Aqaba represents a small scale, easy to access, regional analogue of larger oceanic oligotrophic systems. In this Gulf, the seasonal cycles of stratification and mixing drives the seasonal phytoplankton dynamics. In summer and fall, when nutrient concentrations are very low, Prochlorococcus and Synechococcus are more abundant in the surface water. This two populations are exposed to phosphate limitation. During winter mixing, when nutrient concentrations are high, Chlorophyceae and Cryptophyceae are dominant but scarce or absent during summer. In this study it was tried to develop a simulation model based on historical data to predict the phytoplankton dynamics in the northern Gulf of Aqaba. The purpose is to understand what forces operate, and how, to determine the phytoplankton dynamics in this Gulf. To make the models data sampled in two different sampling station (Fish Farm Station and Station A) were used. The data of chemical, biological and physical factors, are available from 14th January 2007 to 28th December 2009. The Fish Farm Station point was near a Fish Farm that was operational until 17th June 2008, complete closure date of the Fish Farm, about halfway through the total sampling time. The Station A sampling point is about 13 Km away from the Fish Farm Station. To build the model, the MATLAB software was used (version 7.6.0.324 R2008a), in particular a tool named Simulink. The Fish Farm Station models shows that the Fish Farm activity has altered the nutrient concentrations and as a consequence the normal phytoplankton dynamics. Despite the distance between the two sampling stations, there might be an influence from the Fish Farm activities also in the Station A ecosystem. The models about this sampling station shows that the Fish Farm impact appears to be much lower than the impact in the Fish Farm Station, because the phytoplankton dynamics appears to be driven mainly by the seasonal mixing cycle.

Sintesi e caratterizzazione di materiali polimerici water-soluble per applicazioni nel campo del fotovoltaico organico

The need to use renewable energy sources, due to the massive production of pollution for the energy production, has led to the development of new technologies for the use of solar energy. The purpose of this thesis project is to synthesize and characterize new thiophene-based polymeric materials processable in water, a green solvent, for the construction of organic solar cells, promising and versatile devices used for the production of electric energy. For this, a highly regioregular polymer was synthesized through GRIM polymerization (Grignard Metathesis Polymerization) on which a study was performed to identify the optimal reaction time.

Distributed non-cooperative robust economic predictive control for dynamically coupled linear systems.

In this thesis, a tube-based Distributed Economic Predictive Control (DEPC) scheme is presented for a group of dynamically coupled linear subsystems. These subsystems are components of a large scale system and control inputs are computed based on optimizing a local economic objective. Each subsystem is interacting with its neighbors by sending its future reference trajectory, at each sampling time. It solves a local optimization problem in parallel, based on the received future reference trajectories of the other subsystems. To ensure recursive feasibility and a performance bound, each subsystem is constrained to not deviate too much from its communicated reference trajectory. This difference between the plan trajectory and the communicated one is interpreted as a disturbance on the local level. Then, to ensure the satisfaction of both state and input constraints, they are tightened by considering explicitly the effect of these local disturbances. The proposed approach averages over all possible disturbances, handles tightened state and input constraints, while satisfies the compatibility constraints to guarantee that the actual trajectory lies within a certain bound in the neighborhood of the reference one. Each subsystem is optimizing a local arbitrary economic objective function in parallel while considering a local terminal constraint to guarantee recursive feasibility. In this framework, economic performance guarantees for a tube-based distributed predictive control (DPC) scheme are developed rigorously. It is presented that the closed-loop nominal subsystem has a robust average performance bound locally which is no worse than that of a local robust steady state. Since a robust algorithm is applying on the states of the real (with disturbances) subsystems, this bound can be interpreted as an average performance result for the real closed-loop system. To this end, we present our outcomes on local and global performance, illustrated by a numerical example.

Implementazione su fpga di un pre-distorsore digitale a banda larga per sistemi a microonde di backhaul

The development of next generation microwave technology for backhauling systems is driven by an increasing capacity demand. In order to provide higher data rates and throughputs over a point-to-point link, a cost-effective performance improvement is enabled by an enhanced energy-efficiency of the transmit power amplification stage, whereas a combination of spectrally efficient modulation formats and wider bandwidths is supported by amplifiers that fulfil strict constraints in terms of linearity. An optimal trade-off between these conflicting requirements can be achieved by resorting to flexible digital signal processing techniques at baseband. In such a scenario, the adaptive digital pre-distortion is a well-known linearization method, that comes up to be a potentially widely-used solution since it can be easily integrated into base stations. Its operation can effectively compensate for the inter-modulation distortion introduced by the power amplifier, keeping up with the frequency-dependent time-varying behaviour of the relative nonlinear characteristic. In particular, the impact of the memory effects become more relevant and their equalisation become more challenging as the input discrete signal feature a wider bandwidth and a faster envelope to pre-distort. This thesis project involves the research, design and simulation a pre-distorter implementation at RTL based on a novel polyphase architecture, which makes it capable of operating over very wideband signals at a sampling rate that complies with the actual available clock speed of current digital devices. The motivation behind this structure is to carry out a feasible pre-distortion for the multi-band spectrally efficient complex signals carrying multiple channels that are going to be transmitted in near future high capacity and reliability microwave backhaul links.

The contribution of the Finite Volume Point Dilution Method to the determination of solute mass flux in an alluvial aquifer.

Groundwater represents one of the most important resources of the world and it is essential to prevent its pollution and to consider remediation intervention in case of contamination. According to the scientific community the characterization and the management of the contaminated sites have to be performed in terms of contaminant fluxes and considering their spatial and temporal evolution. One of the most suitable approach to determine the spatial distribution of pollutant and to quantify contaminant fluxes in groundwater is using control panels. The determination of contaminant mass flux, requires measurement of contaminant concentration in the moving phase (water) and velocity/flux of the groundwater. In this Master Thesis a new solute flux mass measurement approach, based on an integrated control panel type methodology combined with the Finite Volume Point Dilution Method (FVPDM), for the monitoring of transient groundwater fluxes, is proposed. Moreover a new adsorption passive sampler, which allow to capture the variation of solute concentration with time, is designed. The present work contributes to the development of this approach on three key points. First, the ability of the FVPDM to monitor transient groundwater fluxes was verified during a step drawdown test at the experimental site of Hermalle Sous Argentau (Belgium). The results showed that this method can be used, with optimal results, to follow transient groundwater fluxes. Moreover, it resulted that performing FVPDM, in several piezometers, during a pumping test allows to determine the different flow rates and flow regimes that can occurs in the various parts of an aquifer. The second field test aiming to determine the representativity of a control panel for measuring mass flus in groundwater underlined that wrong evaluations of Darcy fluxes and discharge surfaces can determine an incorrect estimation of mass fluxes and that this technique has to be used with precaution. Thus, a detailed geological and hydrogeological characterization must be conducted, before applying this technique. Finally, the third outcome of this work concerned laboratory experiments. The test conducted on several type of adsorption material (Oasis HLB cartridge, TDS-ORGANOSORB 10 and TDS-ORGANOSORB 10-AA), in order to determine the optimum medium to dimension the passive sampler, highlighted the necessity to find a material with a reversible adsorption tendency to completely satisfy the request of the new passive sampling technique.

An optimal control tool for trajectory generation of autonomous drones

In the recent years, autonomous aerial vehicles gained large popularity in a variety of applications in the field of automation. To accomplish various and challenging tasks the capability of generating trajectories has assumed a key role. As higher performances are sought, traditional, flatness-based trajectory generation schemes present their limitations. In these approaches the highly nonlinear dynamics of the quadrotor is, indeed, neglected. Therefore, strategies based on optimal control principles turn out to be beneficial, since in the trajectory generation process they allow the control unit to best exploit the actual dynamics, and enable the drone to perform quite aggressive maneuvers. This dissertation is then concerned with the development of an optimal control technique to generate trajectories for autonomous drones. The algorithm adopted to this end is a second-order iterative method working directly in continuous-time, which, under proper initialization, guarantees quadratic convergence to a locally optimal trajectory. At each iteration a quadratic approximation of the cost functional is minimized and a decreasing direction is then obtained as a linear-affine control law, after solving a differential Riccati equation. The algorithm has been implemented and its effectiveness has been tested on the vectored-thrust dynamical model of a quadrotor in a realistic simulative setup.

Smart sampling approaches for Decision-Focused Learning

Many real-word decision- making problems are defined based on forecast parameters: for example, one may plan an urban route by relying on traffic predictions. In these cases, the conventional approach consists in training a predictor and then solving an optimization problem. This may be problematic since mistakes made by the predictor may trick the optimizer into taking dramatically wrong decisions. Recently, the field of Decision-Focused Learning overcomes this limitation by merging the two stages at training time, so that predictions are rewarded and penalized based on their outcome in the optimization problem. There are however still significant challenges toward a widespread adoption of the method, mostly related to the limitation in terms of generality and scalability. One possible solution for dealing with the second problem is introducing a caching-based approach, to speed up the training process. This project aims to investigate these techniques, in order to reduce even more, the solver calls. For each considered method, we designed a particular smart sampling approach, based on their characteristics. In the case of the SPO method, we ended up discovering that it is only necessary to initialize the cache with only several solutions; those needed to filter the elements that we still need to properly learn. For the Blackbox method, we designed a smart sampling approach, based on inferred solutions.